/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram (mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram (mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram (mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram (mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram (mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram (SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram (SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram (SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram (SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */
+ mtsdram (SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram (mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram (mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
+ mtsdram (SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram (SDRAM0_TR0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
/* RA=10 RD=3 */
- mtsdram (mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
- mtsdram (mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
- mtsdram (mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
+ mtsdram (SDRAM0_TR1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
+ mtsdram (SDRAM0_RTR, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
+ mtsdram (SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
udelay (400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram (mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram (SDRAM0_CFG0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
for (;;) {
- mfsdram (mem_mcsts, reg);
+ mfsdram (SDRAM0_MCSTS, reg);
if (reg & 0x80000000)
break;
}
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The metrobox is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIX0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
-/*************************************************************************
- * is_pci_host
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* The metrobox is always configured as host. */
- return(1);
-}
-#endif /* defined(CONFIG_PCI) */
-
/*************************************************************************
* board_get_enetaddr
*
* mgmt mac address.
*
************************************************************************/
-static int macaddr_idx = 0;
-void board_get_enetaddr (uchar * enet)
+void board_get_enetaddr(int macaddr_idx, uchar *enet)
{
int i;
unsigned short tmp;
tmp += 31;
memcpy(&enet[4], &tmp, 2);
- macaddr_idx++;
} else {
enet[0] = 0x02;
enet[1] = 0x00;