+// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
* Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
* Copyright (C) 2009 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <init.h>
+#include <asm/global_data.h>
#include <linux/sizes.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/at91_matrix.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#include <lcd.h>
-#include <atmel_lcdc.h>
-#include <dataflash.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
+#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
- * Miscelaneous platform dependent initialisations
+ * Miscellaneous platform dependent initializations
*/
#ifdef CONFIG_CMD_NAND
&smc->cs[3].mode);
/* Configure RDY/BSY */
- gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
+ gpio_direction_input(CFG_SYS_NAND_READY_PIN);
/* Enable NandFlash */
- gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
-}
-#endif
-
-#ifdef CONFIG_MACB
-static void pm9263_macb_hw_init(void)
-{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
- /*
- * PB27 enables the 50MHz oscillator for Ethernet PHY
- * 1 - enable
- * 0 - disable
- */
- at91_set_pio_output(AT91_PIO_PORTB, 27, 1);
- at91_set_pio_value(AT91_PIO_PORTB, 27, 1); /* 1- enable, 0 - disable */
-
- /* Enable clock */
- writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
-
- /*
- * Disable pull-up on:
- * RXDV (PC25) => PHY normal mode (not Test mode)
- * ERX0 (PE25) => PHY ADDR0
- * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
-
- at91_set_pio_pullup(AT91_PIO_PORTC, 25, 0);
- at91_set_pio_pullup(AT91_PIO_PORTE, 25, 0);
- at91_set_pio_pullup(AT91_PIO_PORTE, 26, 0);
-
- /* Re-enable pull-up */
- at91_set_pio_pullup(AT91_PIO_PORTC, 25, 1);
- at91_set_pio_pullup(AT91_PIO_PORTE, 25, 1);
- at91_set_pio_pullup(AT91_PIO_PORTE, 26, 1);
-
- at91_macb_hw_init();
-}
-#endif
-
-#ifdef CONFIG_LCD
-vidinfo_t panel_info = {
- .vl_col = 240,
- .vl_row = 320,
- .vl_clk = 4965000,
- .vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
- ATMEL_LCDC_INVFRAME_INVERTED,
- .vl_bpix = 3,
- .vl_tft = 1,
- .vl_hsync_len = 5,
- .vl_left_margin = 1,
- .vl_right_margin = 33,
- .vl_vsync_len = 1,
- .vl_upper_margin = 1,
- .vl_lower_margin = 0,
- .mmio = ATMEL_BASE_LCDC,
-};
-
-void lcd_enable(void)
-{
- at91_set_pio_value(AT91_PIO_PORTA, 22, 1); /* power up */
-}
-
-void lcd_disable(void)
-{
- at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power down */
-}
-
-#ifdef CONFIG_LCD_IN_PSRAM
-
-#define PSRAM_CRE_PIN AT91_PIO_PORTB, 29
-#define PSRAM_CTRL_REG (PHYS_PSRAM + PHYS_PSRAM_SIZE - 2)
-
-/* Initialize the PSRAM memory */
-static int pm9263_lcd_hw_psram_init(void)
-{
- unsigned long csa;
- struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC1;
- struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
-
- /* Enable CS3 3.3v, no pull-ups */
- csa = readl(&matrix->csa[1]) | AT91_MATRIX_CSA_DBPUC |
- AT91_MATRIX_CSA_VDDIOMSEL_3_3V;
-
- writel(csa, &matrix->csa[1]);
-
- /* Configure SMC1 CS0 for PSRAM - 16-bit */
- writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
- AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0),
- &smc->cs[0].setup);
-
- writel(AT91_SMC_PULSE_NWE(7) | AT91_SMC_PULSE_NCS_WR(7) |
- AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(7),
- &smc->cs[0].pulse);
-
- writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8),
- &smc->cs[0].cycle);
-
- writel(AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_PMEN | AT91_SMC_MODE_PS_32,
- &smc->cs[0].mode);
-
- /* setup PB29 as output */
- at91_set_pio_output(PSRAM_CRE_PIN, 1);
-
- at91_set_pio_value(PSRAM_CRE_PIN, 0); /* set PSRAM_CRE_PIN to '0' */
-
- /* PSRAM: write BCR */
- readw(PSRAM_CTRL_REG);
- readw(PSRAM_CTRL_REG);
- writew(1, PSRAM_CTRL_REG); /* 0 - RCR,1 - BCR */
- writew(0x9d4f, PSRAM_CTRL_REG); /* write the BCR */
-
- /* write RCR of the PSRAM */
- readw(PSRAM_CTRL_REG);
- readw(PSRAM_CTRL_REG);
- writew(0, PSRAM_CTRL_REG); /* 0 - RCR,1 - BCR */
- /* set RCR; 0x10-async mode,0x90-page mode */
- writew(0x90, PSRAM_CTRL_REG);
-
- /*
- * test to see if the PSRAM is MT45W2M16A or MT45W2M16B
- * MT45W2M16B - CRE must be 0
- * MT45W2M16A - CRE must be 1
- */
- writew(0x1234, PHYS_PSRAM);
- writew(0x5678, PHYS_PSRAM + 2);
-
- /* test if the chip is MT45W2M16B */
- if ((readw(PHYS_PSRAM) != 0x1234) || (readw(PHYS_PSRAM+2) != 0x5678)) {
- /* try with CRE=1 (MT45W2M16A) */
- at91_set_pio_value(PSRAM_CRE_PIN, 1); /* set PSRAM_CRE_PIN to '1' */
-
- /* write RCR of the PSRAM */
- readw(PSRAM_CTRL_REG);
- readw(PSRAM_CTRL_REG);
- writew(0, PSRAM_CTRL_REG); /* 0 - RCR,1 - BCR */
- /* set RCR;0x10-async mode,0x90-page mode */
- writew(0x90, PSRAM_CTRL_REG);
-
-
- writew(0x1234, PHYS_PSRAM);
- writew(0x5678, PHYS_PSRAM+2);
- if ((readw(PHYS_PSRAM) != 0x1234)
- || (readw(PHYS_PSRAM + 2) != 0x5678))
- return 1;
-
- }
-
- /* Bus matrix */
- writel(AT91_MATRIX_PRA_M5(3), &matrix->pr[5].a);
- writel(CONFIG_PSRAM_SCFG, &matrix->scfg[5]);
-
- return 0;
+ gpio_direction_output(CFG_SYS_NAND_ENABLE_PIN, 1);
}
#endif
-static void pm9263_lcd_hw_init(void)
-{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
- at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDVSYNC */
- at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */
- at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */
- at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */
- at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */
- at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */
- at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */
- at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */
- at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */
- at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */
- at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */
- at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */
- at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */
- at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */
- at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */
- at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */
- at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */
- at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */
- at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */
- at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */
- at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */
- at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */
- at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */
-
- writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
-
- /* Power Control */
- at91_set_pio_output(AT91_PIO_PORTA, 22, 1);
- at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power down */
-
-#ifdef CONFIG_LCD_IN_PSRAM
- /* initialize te PSRAM */
- int stat = pm9263_lcd_hw_psram_init();
-
- gd->fb_base = (stat == 0) ? PHYS_PSRAM : ATMEL_BASE_SRAM0;
-#else
- gd->fb_base = ATMEL_BASE_SRAM0;
-#endif
-
-}
-
-#ifdef CONFIG_LCD_INFO
-#include <nand.h>
-#include <version.h>
-
-extern flash_info_t flash_info[];
-
-void lcd_show_board_info(void)
-{
- ulong dram_size, nand_size, flash_size, dataflash_size;
- int i;
- char temp[32];
-
- lcd_printf ("%s\n", U_BOOT_VERSION);
- lcd_printf ("(C) 2009 Ronetix GmbH\n");
- lcd_printf ("support@ronetix.at\n");
- lcd_printf ("%s CPU at %s MHz",
- CONFIG_SYS_AT91_CPU_NAME,
- strmhz(temp, get_cpu_clk_rate()));
-
- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
- dram_size += gd->bd->bi_dram[i].size;
-
- nand_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += nand_info[i].size;
-
- flash_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
- flash_size += flash_info[i].size;
-
- dataflash_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_DATAFLASH_BANKS; i++)
- dataflash_size += (unsigned int) dataflash_info[i].Device.pages_number *
- dataflash_info[i].Device.pages_size;
-
- lcd_printf ("%ld MB SDRAM, %ld MB NAND\n%ld MB NOR Flash\n"
- "4 MB PSRAM, %ld MB DataFlash\n",
- dram_size >> 20,
- nand_size >> 20,
- flash_size >> 20,
- dataflash_size >> 20);
-}
-#endif /* CONFIG_LCD_INFO */
-
-#endif /* CONFIG_LCD */
-
int board_early_init_f(void)
{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
- /* Enable clocks for all PIOs */
- writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
- (1 << ATMEL_ID_PIOCDE),
- &pmc->pcer);
-
- at91_seriald_hw_init();
-
return 0;
}
int board_init(void)
{
- /* arch number of AT91SAM9263EK-Board */
+ /* arch number of PM9263 Board */
gd->bd->bi_arch_number = MACH_TYPE_PM9263;
- /* adress of boot parameters */
+ /* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_CMD_NAND
pm9263_nand_hw_init();
#endif
-#ifdef CONFIG_HAS_DATAFLASH
- at91_spi0_hw_init(1 << 0);
-#endif
-#ifdef CONFIG_MACB
- pm9263_macb_hw_init();
-#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
-#ifdef CONFIG_LCD
- pm9263_lcd_hw_init();
-#endif
return 0;
}
int dram_init(void)
{
- /* dram_init must store complete ramsize in gd->ram_size */
+ /* dram_init must store complete RAM size in gd->ram_size */
gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
PHYS_SDRAM_SIZE);
return 0;
}
-void dram_init_banksize(void)
+int dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM;
gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-void reset_phy(void)
-{
-}
-#endif
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x01);
-#endif
- return rc;
+ return 0;
}
#ifdef CONFIG_DISPLAY_BOARDINFO