+// SPDX-License-Identifier: GPL-2.0
/*
* (C) Copyright 2012-2016 Stephen Warren
- *
- * SPDX-License-Identifier: GPL-2.0
*/
#include <common.h>
-#include <inttypes.h>
#include <config.h>
#include <dm.h>
+#include <environment.h>
#include <efi_loader.h>
#include <fdt_support.h>
#include <fdt_simplefb.h>
#endif
/*
- * http://raspberryalphaomega.org.uk/2013/02/06/automatic-raspberry-pi-board-revision-detection-model-a-b1-and-b2/
- * http://www.raspberrypi.org/forums/viewtopic.php?f=63&t=32733
- * http://git.drogon.net/?p=wiringPi;a=blob;f=wiringPi/wiringPi.c;h=503151f61014418b9c42f4476a6086f75cd4e64b;hb=refs/heads/master#l922
- *
- * In http://lists.denx.de/pipermail/u-boot/2016-January/243752.html
- * ("[U-Boot] [PATCH] rpi: fix up Model B entries") Dom Cobley at the RPi
- * Foundation stated that the following source was accurate:
- * https://github.com/AndrewFromMelbourne/raspberry_pi_revision
+ * https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md
*/
struct rpi_model {
const char *name;
};
static const struct rpi_model rpi_models_new_scheme[] = {
+ [0x0] = {
+ "Model A",
+ DTB_DIR "bcm2835-rpi-a.dtb",
+ false,
+ },
+ [0x1] = {
+ "Model B",
+ DTB_DIR "bcm2835-rpi-b.dtb",
+ true,
+ },
+ [0x2] = {
+ "Model A+",
+ DTB_DIR "bcm2835-rpi-a-plus.dtb",
+ false,
+ },
+ [0x3] = {
+ "Model B+",
+ DTB_DIR "bcm2835-rpi-b-plus.dtb",
+ true,
+ },
[0x4] = {
"2 Model B",
DTB_DIR "bcm2836-rpi-2-b.dtb",
true,
},
+ [0x6] = {
+ "Compute Module",
+ DTB_DIR "bcm2835-rpi-cm.dtb",
+ false,
+ },
[0x8] = {
"3 Model B",
DTB_DIR "bcm2837-rpi-3-b.dtb",
DTB_DIR "bcm2835-rpi-zero.dtb",
false,
},
+ [0xA] = {
+ "Compute Module 3",
+ DTB_DIR "bcm2837-rpi-cm3.dtb",
+ false,
+ },
[0xC] = {
"Zero W",
DTB_DIR "bcm2835-rpi-zero-w.dtb",
false,
},
+ [0xD] = {
+ "3 Model B+",
+ DTB_DIR "bcm2837-rpi-3-b-plus.dtb",
+ true,
+ },
+ [0xE] = {
+ "3 Model A+",
+ DTB_DIR "bcm2837-rpi-3-a-plus.dtb",
+ false,
+ },
};
static const struct rpi_model rpi_models_old_scheme[] = {
return;
}
- snprintf(serial_string, sizeof(serial_string), "%016" PRIx64,
+ snprintf(serial_string, sizeof(serial_string), "%016llx",
msg->get_board_serial.body.resp.serial);
env_set("serial#", serial_string);
}
printf("RPI %s (0x%x)\n", model->name, revision);
}
-#ifndef CONFIG_PL01X_SERIAL
-static bool rpi_is_serial_active(void)
-{
- int serial_gpio = 15;
- struct udevice *dev;
-
- /*
- * The RPi3 disables the mini uart by default. The easiest way to find
- * out whether it is available is to check if the RX pin is muxed.
- */
-
- if (uclass_first_device(UCLASS_PINCTRL, &dev) || !dev)
- return true;
-
- if (pinctrl_get_gpio_mux(dev, 0, serial_gpio) != BCM2835_GPIO_ALT5)
- return false;
-
- return true;
-}
-
-/* Disable mini-UART I/O if it's not pinmuxed to our pins.
- * The firmware only enables it if explicitly done in config.txt: enable_uart=1
- */
-static void rpi_disable_inactive_uart(void)
-{
- struct udevice *dev;
- struct bcm283x_mu_serial_platdata *plat;
-
- if (uclass_get_device_by_driver(UCLASS_SERIAL,
- DM_GET_DRIVER(serial_bcm283x_mu),
- &dev) || !dev)
- return;
-
- if (!rpi_is_serial_active()) {
- plat = dev_get_platdata(dev);
- plat->disabled = true;
- }
-}
-#endif
-
int board_init(void)
{
#ifdef CONFIG_HW_WATCHDOG
hw_watchdog_init();
#endif
-#ifndef CONFIG_PL01X_SERIAL
- rpi_disable_inactive_uart();
-#endif
get_board_rev();