#include <spd_sdram.h>
#include <status_led.h>
#include <sha1.h>
+#include <asm/io.h>
+#include <net.h>
DECLARE_GLOBAL_DATA_PTR;
-extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
unsigned char sha1_checksum[SHA1_SUM_LEN];
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* GPIO's are alreay setup in cpu/ppc4xx/cpu_init.c
/*--------------------------------------------------------------------
* Setup other serial configuration
*-------------------------------------------------------------------*/
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00000100); /* Pin function: enable GPIO49-63 */
- mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
+ mtsdr(SDR0_PFC0, 0x00000000); /* Pin function: enable GPIO49-63 */
+ mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
return 0;
}
#define EEPROM_LEN 256
-void load_sernum_ethaddr (void)
+static void load_ethaddr(void)
{
+ int ok_ethaddr, ok_eth1addr;
int ret;
- char buf[EEPROM_LEN];
- char mac[32];
+ uchar buf[EEPROM_LEN];
char *use_eeprom;
u16 checksumcrc16 = 0;
+ /* If the env is sane, then nothing for us to do */
+ ok_ethaddr = eth_getenv_enetaddr("ethaddr", buf);
+ ok_eth1addr = eth_getenv_enetaddr("eth1addr", buf);
+ if (ok_ethaddr && ok_eth1addr)
+ return;
+
/* read the MACs from EEprom */
status_led_set (0, STATUS_LED_ON);
status_led_set (1, STATUS_LED_ON);
- ret = eeprom_read (CFG_I2C_EEPROM_ADDR, 0, (uchar *)buf, EEPROM_LEN);
+ ret = eeprom_read (CONFIG_SYS_I2C_EEPROM_ADDR, 0, buf, EEPROM_LEN);
if (ret == 0) {
- checksumcrc16 = cyg_crc16 ((uchar *)buf, EEPROM_LEN - 2);
+ checksumcrc16 = cyg_crc16 (buf, EEPROM_LEN - 2);
/* check, if the EEprom is programmed:
* - The Prefix(Byte 0,1,2) is equal to "ATR"
* - The checksum, stored in the last 2 Bytes, is correct
*/
- if ((strncmp (buf,"ATR",3) != 0) ||
+ if ((strncmp ((char *)buf,"ATR",3) != 0) ||
((checksumcrc16 >> 8) != buf[EEPROM_LEN - 2]) ||
((checksumcrc16 & 0xff) != buf[EEPROM_LEN - 1])) {
/* EEprom is not programmed */
printf("%s: EEPROM Checksum not OK\n", __FUNCTION__);
} else {
/* get the MACs */
- sprintf (mac, "%02x:%02x:%02x:%02x:%02x:%02x",
- buf[3],
- buf[4],
- buf[5],
- buf[6],
- buf[7],
- buf[8]);
- setenv ("ethaddr", (char *) mac);
- sprintf (mac, "%02x:%02x:%02x:%02x:%02x:%02x",
- buf[9],
- buf[10],
- buf[11],
- buf[12],
- buf[13],
- buf[14]);
- setenv ("eth1addr", (char *) mac);
+ if (!ok_ethaddr)
+ eth_setenv_enetaddr("ethaddr", &buf[3]);
+ if (!ok_eth1addr)
+ eth_setenv_enetaddr("eth1addr", &buf[9]);
return;
}
}
unsigned char org[20];
int i, len = CONFIG_SHA1_LEN;
- memcpy ((char *)CFG_LOAD_ADDR, (char *)CONFIG_SHA1_START, len);
- data = (unsigned char *)CFG_LOAD_ADDR;
+ memcpy ((char *)CONFIG_SYS_LOAD_ADDR, (char *)CONFIG_SHA1_START, len);
+ data = (unsigned char *)CONFIG_SYS_LOAD_ADDR;
ptroff = &data[len + SHA1_SUM_POS];
for (i = 0; i < SHA1_SUM_LEN; i++) {
uint pbcr;
int size_val = 0;
+ load_ethaddr();
+
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- -CFG_MONITOR_LEN,
+ -CONFIG_SYS_MONITOR_LEN,
0xffffffff,
&flash_info[1]);
/* Env protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
+ CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
&flash_info[1]);
pcs440ep_readinputs ();
}
}
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
long dram_size = 0;
return dram_size;
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
* may not be sufficient for a given board.
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
/*--------------------------------------------------------------------------+
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
/* Program the board's subsystem id/vendor id */
pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CFG_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
+ CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
/* Configure command register as bus master */
pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
/*************************************************************************
* pci_master_init
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
unsigned short temp_short;
temp_short | PCI_COMMAND_MASTER |
PCI_COMMAND_MEMORY);
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
/*************************************************************************
* is_pci_host
}
U_BOOT_CMD(
- led, 2, 1, do_led,
- "led [bitmask] - set the DIAG-LED\n",
+ led, 2, 1, do_led,
+ "set the DIAG-LED",
"[bitmask] 0x01 = DIAG 1 on\n"
" 0x02 = DIAG 2 on\n"
" 0x04 = DIAG 3 on\n"
" 0x08 = DIAG 4 on\n"
- " > 0x100 set the LED, who are on, to state blinking\n"
+ " > 0x100 set the LED, who are on, to state blinking"
);
#if defined(CONFIG_SHA1_CHECK_UB_IMG)
if (argc < 2) {
usage:
- printf ("Usage:\n%s\n", cmdtp->usage);
+ cmd_usage(cmdtp);
return 1;
}
}
U_BOOT_CMD(
- sha1, 4, 1, do_sha1,
- "sha1 - calculate the SHA1 Sum\n",
+ sha1, 4, 1, do_sha1,
+ "calculate the SHA1 Sum",
"address len [addr] calculate the SHA1 sum [save at addr]\n"
" -p calculate the SHA1 sum from the U-Boot image in flash and print\n"
- " -c check the U-Boot image in flash\n"
+ " -c check the U-Boot image in flash"
);
#endif
+#if defined (CONFIG_CMD_IDE)
+/* These addresses need to be shifted one place to the left
+ * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0)
+ * These values are shifted
+ */
+extern ulong *ide_bus_offset;
+void inline ide_outb(int dev, int port, unsigned char val)
+{
+ debug ("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
+ dev, port, val, (ATA_CURR_BASE(dev)+port));
+
+ out_be16((u16 *)(ATA_CURR_BASE(dev)+(port << 1)), val);
+}
+unsigned char inline ide_inb(int dev, int port)
+{
+ uchar val;
+ val = in_be16((u16 *)(ATA_CURR_BASE(dev)+(port << 1)));
+ debug ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
+ dev, port, (ATA_CURR_BASE(dev)+port), val);
+ return (val);
+}
+#endif
+
#ifdef CONFIG_IDE_PREINIT
int ide_preinit (void)
{
projects / platform / kernel / u-boot.git / blobdiff