#include <spd_sdram.h>
#include <status_led.h>
#include <sha1.h>
+#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
*-------------------------------------------------------------------*/
mfsdr(sdr_pci0, reg);
mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00000100); /* Pin function: enable GPIO49-63 */
+ mtsdr(sdr_pfc0, 0x00000000); /* Pin function: enable GPIO49-63 */
mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
return 0;
/* Env protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
+ CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
&flash_info[1]);
pcs440ep_readinputs ();
}
}
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
long dram_size = 0;
return dram_size;
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
}
U_BOOT_CMD(
- led, 2, 1, do_led,
- "led [bitmask] - set the DIAG-LED\n",
+ led, 2, 1, do_led,
+ "led [bitmask] - set the DIAG-LED\n",
"[bitmask] 0x01 = DIAG 1 on\n"
" 0x02 = DIAG 2 on\n"
" 0x04 = DIAG 3 on\n"
}
U_BOOT_CMD(
- sha1, 4, 1, do_sha1,
- "sha1 - calculate the SHA1 Sum\n",
+ sha1, 4, 1, do_sha1,
+ "sha1 - calculate the SHA1 Sum\n",
"address len [addr] calculate the SHA1 sum [save at addr]\n"
" -p calculate the SHA1 sum from the U-Boot image in flash and print\n"
" -c check the U-Boot image in flash\n"
);
#endif
+#if defined (CONFIG_CMD_IDE)
+/* These addresses need to be shifted one place to the left
+ * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0)
+ * These values are shifted
+ */
+extern ulong *ide_bus_offset;
+void inline ide_outb(int dev, int port, unsigned char val)
+{
+ debug ("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
+ dev, port, val, (ATA_CURR_BASE(dev)+port));
+
+ out_be16((u16 *)(ATA_CURR_BASE(dev)+(port << 1)), val);
+}
+unsigned char inline ide_inb(int dev, int port)
+{
+ uchar val;
+ val = in_be16((u16 *)(ATA_CURR_BASE(dev)+(port << 1)));
+ debug ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
+ dev, port, (ATA_CURR_BASE(dev)+port), val);
+ return (val);
+}
+#endif
+
#ifdef CONFIG_IDE_PREINIT
int ide_preinit (void)
{
}
#endif
-#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+#if defined (CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET)
void ide_set_reset (int idereset)
{
debug ("ide_reset(%d)\n", idereset);
}
udelay (10000);
}
-#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */
+#endif /* defined (CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET) */