#include <common.h>
#include "mip405.h"
#include <asm/processor.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
#include <miiphy.h>
#include "../common/common_util.h"
+#include <stdio_dev.h>
#include <i2c.h>
#include <rtc.h>
-extern block_dev_desc_t * scsi_get_dev(int dev);
-extern block_dev_desc_t * ide_get_dev(int dev);
+
+DECLARE_GLOBAL_DATA_PTR;
#undef SDRAM_DEBUG
#define ENABLE_ECC /* for ecc boards */
#endif
-#define PLD_PART_REG PER_PLD_ADDR + 0
-#define PLD_VERS_REG PER_PLD_ADDR + 1
-#define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2
-#define PLD_IRQ_REG PER_PLD_ADDR + 3
-#define PLD_COM_MODE_REG PER_PLD_ADDR + 4
-#define PLD_EXT_CONF_REG PER_PLD_ADDR + 5
+#define PLD_PART_REG PER_PLD_ADDR + 0
+#define PLD_VERS_REG PER_PLD_ADDR + 1
+#define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2
+#define PLD_IRQ_REG PER_PLD_ADDR + 3
+#define PLD_COM_MODE_REG PER_PLD_ADDR + 4
+#define PLD_EXT_CONF_REG PER_PLD_ADDR + 5
#define MEGA_BYTE (1024*1024)
void SDRAM_err (const char *s)
{
#ifndef SDRAM_DEBUG
- DECLARE_GLOBAL_DATA_PTR;
-
(void) get_clocks ();
gd->baudrate = 9600;
serial_init ();
int init_sdram (void)
{
- DECLARE_GLOBAL_DATA_PTR;
-
unsigned long tmp, baseaddr;
unsigned short i;
unsigned char trp_clocks,
unsigned char bc;
unsigned long sdram_tim, sdram_bank;
- /*i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);*/
+ /*i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);*/
(void) get_clocks ();
gd->baudrate = 9600;
serial_init ();
/* set up the pld */
- mtdcr (ebccfga, pb7ap);
- mtdcr (ebccfgd, PLD_AP);
- mtdcr (ebccfga, pb7cr);
- mtdcr (ebccfgd, PLD_CR);
+ mtdcr (EBC0_CFGADDR, PB7AP);
+ mtdcr (EBC0_CFGDATA, PLD_AP);
+ mtdcr (EBC0_CFGADDR, PB7CR);
+ mtdcr (EBC0_CFGDATA, PLD_CR);
/* THIS IS OBSOLETE */
/* set up the board rev reg*/
- mtdcr (ebccfga, pb5ap);
- mtdcr (ebccfgd, BOARD_AP);
- mtdcr (ebccfga, pb5cr);
- mtdcr (ebccfgd, BOARD_CR);
+ mtdcr (EBC0_CFGADDR, PB5AP);
+ mtdcr (EBC0_CFGDATA, BOARD_AP);
+ mtdcr (EBC0_CFGADDR, PB5CR);
+ mtdcr (EBC0_CFGDATA, BOARD_CR);
#ifdef SDRAM_DEBUG
/* get all informations from PLD */
serial_puts ("\nPLD Part 0x");
SDRAM_err ("U-Boot configured for a MIP405 not for a MIP405T!!!\n");
#endif
/* set-up the chipselect machine */
- mtdcr (ebccfga, pb0cr); /* get cs0 config reg */
- tmp = mfdcr (ebccfgd);
+ mtdcr (EBC0_CFGADDR, PB0CR); /* get cs0 config reg */
+ tmp = mfdcr (EBC0_CFGDATA);
if ((tmp & 0x00002000) == 0) {
/* MPS Boot, set up the flash */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, FLASH_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, FLASH_CR);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, FLASH_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, FLASH_CR);
} else {
/* Flash boot, set up the MPS */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, MPS_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, MPS_CR);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, MPS_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, MPS_CR);
}
/* set up UART0 (CS2) and UART1 (CS3) */
- mtdcr (ebccfga, pb2ap);
- mtdcr (ebccfgd, UART0_AP);
- mtdcr (ebccfga, pb2cr);
- mtdcr (ebccfgd, UART0_CR);
- mtdcr (ebccfga, pb3ap);
- mtdcr (ebccfgd, UART1_AP);
- mtdcr (ebccfga, pb3cr);
- mtdcr (ebccfgd, UART1_CR);
+ mtdcr (EBC0_CFGADDR, PB2AP);
+ mtdcr (EBC0_CFGDATA, UART0_AP);
+ mtdcr (EBC0_CFGADDR, PB2CR);
+ mtdcr (EBC0_CFGDATA, UART0_CR);
+ mtdcr (EBC0_CFGADDR, PB3AP);
+ mtdcr (EBC0_CFGDATA, UART1_AP);
+ mtdcr (EBC0_CFGADDR, PB3CR);
+ mtdcr (EBC0_CFGDATA, UART1_CR);
bc = in8 (PLD_BOARD_CFG_REG);
#ifdef SDRAM_DEBUG
serial_puts ("\nstart SDRAM Setup\n");
serial_puts ("\n");
#endif
i = 0;
- baseaddr = CFG_SDRAM_BASE;
+ baseaddr = CONFIG_SYS_SDRAM_BASE;
while (sdram_table[i].sz != 0xff) {
if (sdram_table[i].boardtype == bc)
break;
/* trc_clocks is sum of trp_clocks + tras_clocks */
trc_clocks = trp_clocks + tras_clocks;
/* get SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- sdram_tim = mfdcr (memcfgd) & ~0x018FC01F;
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ sdram_tim = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
/* insert CASL value */
sdram_tim |= ((unsigned long) (cal_val)) << 23;
/* insert PTA value */
/* insert SZ value; */
tmp |= ((unsigned long) sdram_table[i].sz << 17);
/* get SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- sdram_bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ sdram_bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
sdram_bank |= (baseaddr | tmp | 0x01);
#ifdef SDRAM_DEBUG
#endif
/* write SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- mtdcr (memcfgd, sdram_tim);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGDATA, sdram_tim);
#ifdef SDRAM_DEBUG
serial_puts ("mb0cf: ");
#endif
/* write SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- mtdcr (memcfgd, sdram_bank);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGDATA, sdram_bank);
if (get_bus_freq (tmp) > 110000000) { /* > 110MHz */
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x07F00000;
} else {
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x05F00000;
}
/* write SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGDATA, tmp);
/* enable ECC if used */
#if defined(ENABLE_ECC) && !defined(CONFIG_BOOT_PCI)
if (sdram_table[i].ecc) {
#ifdef SDRAM_DEBUG
serial_puts ("disable ECC.. ");
#endif
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp &= 0xff0fffff; /* disable all banks */
- mtdcr (memcfga, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
/* set up SDRAM Controller with ECC enabled */
#ifdef SDRAM_DEBUG
serial_puts ("setup SDRAM Controller.. ");
#endif
- mtdcr (memcfgd, tmp);
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (600);
#ifdef SDRAM_DEBUG
serial_puts ("fill the memory..\n");
serial_puts ("enable ECC\n");
#endif
udelay (400);
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp |= 0x00800000; /* enable bank 0 */
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
} else
#endif
{
/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80C00000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80C00000;
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
}
serial_puts ("\n");
return (0);
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
init_sdram ();
| caused the interrupt.
|
+-------------------------------------------------------------------------*/
- mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr (uicer, 0x00000000); /* disable all ints */
- mtdcr (uiccr, 0x00000000); /* set all to be non-critical (for now) */
- mtdcr (uicpr, 0xFFFFFF80); /* set int polarities */
- mtdcr (uictr, 0x10000000); /* set int trigger levels */
- mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
- mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
+ mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr (UIC0ER, 0x00000000); /* disable all ints */
+ mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical (for now) */
+ mtdcr (UIC0PR, 0xFFFFFF80); /* set int polarities */
+ mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
+ mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
+ mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
return 0;
}
int checkboard (void)
{
- unsigned char s[50];
+ char s[50];
unsigned char bc, var;
int i;
backup_t *b = (backup_t *) s;
puts ("Board: ");
get_pcbrev_var(&bc,&var);
- i = getenv_r ("serial#", s, 32);
- if ((i == 0) || strncmp (s, BOARD_NAME,sizeof(BOARD_NAME))) {
+ i = getenv_r ("serial#", (char *)s, 32);
+ if ((i == 0) || strncmp ((char *)s, BOARD_NAME,sizeof(BOARD_NAME))) {
get_backup_values (b);
if (strncmp (b->signature, "MPL\0", 4) != 0) {
puts ("### No HW ID - assuming " BOARD_NAME);
/* ------------------------------------------------------------------------- */
static int test_dram (unsigned long ramsize);
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
unsigned long bank_reg[4], tmp, bank_size;
ds = 0;
/* since the DRAM controller is allready set up, calculate the size with the
bank registers */
- mtdcr (memcfga, mem_mb0cf);
- bank_reg[0] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb1cf);
- bank_reg[1] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb2cf);
- bank_reg[2] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb3cf);
- bank_reg[3] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
TotalSize = 0;
for (i = 0; i < 4; i++) {
if ((bank_reg[i] & 0x1) == 0x1) {
} else
ds = 1;
}
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (!tmp)
printf ("No ");
int misc_init_r (void)
{
- DECLARE_GLOBAL_DATA_PTR;
/* adjust flash start and size as well as the offset */
gd->bd->bi_flashstart=0-flash_info[0].size;
- gd->bd->bi_flashsize=flash_info[0].size-CFG_MONITOR_LEN;
+ gd->bd->bi_flashsize=flash_info[0].size-CONFIG_SYS_MONITOR_LEN;
gd->bd->bi_flashoffset=0;
/* check, if RTC is running */
rtc_get (&tm);
start=get_timer(0);
/* if MIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
- if (mfdcr(strap) & PSR_ROM_LOC)
- mtspr(ccr0, (mfspr(ccr0) & ~0x80));
+ if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
+ mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
return (0);
}
var, pcbrev + 'A', part & 0x7F, vers);
}
+
+#ifdef CONFIG_POST
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+ return 0; /* No hotkeys supported */
+}
+#endif
+
extern void mem_test_reloc(void);
extern int mk_date (char *, struct rtc_time *);
{
unsigned long stop;
struct rtc_time newtm;
- unsigned char *s;
+ char *s;
mem_test_reloc();
/* write correct LED configuration */
- if (miiphy_write (0x1, 0x14, 0x2402) != 0) {
+ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x14, 0x2402) != 0) {
printf ("Error writing to the PHY\n");
}
/* since LED/CFG2 is not connected on the -2,
* write to correct capability information */
- if (miiphy_write (0x1, 0x4, 0x01E1) != 0) {
+ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x4, 0x01E1) != 0) {
printf ("Error writing to the PHY\n");
}
print_mip405_rev ();
- show_stdio_dev ();
+ stdio_print_current_devices ();
check_env ();
/* check if RTC time is valid */
stop=get_timer(start);