#include <common.h>
#include "mip405.h"
#include <asm/processor.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
#include <miiphy.h>
#include "../common/common_util.h"
+#include <stdio_dev.h>
#include <i2c.h>
-extern block_dev_desc_t * scsi_get_dev(int dev);
-extern block_dev_desc_t * ide_get_dev(int dev);
+#include <rtc.h>
-#undef SDRAM_DEBUG
+DECLARE_GLOBAL_DATA_PTR;
+#undef SDRAM_DEBUG
+#define ENABLE_ECC /* for ecc boards */
#define FALSE 0
#define TRUE 1
#endif
-#define PLD_PART_REG PER_PLD_ADDR + 0
-#define PLD_VERS_REG PER_PLD_ADDR + 1
-#define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2
-#define PLD_IRQ_REG PER_PLD_ADDR + 3
-#define PLD_COM_MODE_REG PER_PLD_ADDR + 4
-#define PLD_EXT_CONF_REG PER_PLD_ADDR + 5
+#define PLD_PART_REG PER_PLD_ADDR + 0
+#define PLD_VERS_REG PER_PLD_ADDR + 1
+#define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2
+#define PLD_IRQ_REG PER_PLD_ADDR + 3
+#define PLD_COM_MODE_REG PER_PLD_ADDR + 4
+#define PLD_EXT_CONF_REG PER_PLD_ADDR + 5
#define MEGA_BYTE (1024*1024)
unsigned char sz; /* log binary => Size = (4MByte<<sz) 5 = 128, 4 = 64, 3 = 32, 2 = 16, 1=8 */
unsigned char ecc; /* if true, ecc is enabled */
} sdram_t;
-
+#if defined(CONFIG_MIP405T)
+const sdram_t sdram_table[] = {
+ { 0x0F, /* MIP405T Rev A, 64MByte -1 Board */
+ 3, /* Case Latenty = 3 */
+ 3, /* trp 20ns / 7.5 ns datain[27] */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 4, /* tcpt 44 - 20ns = 24ns */
+ 2, /* Address Mode = 2 (12x9x4) */
+ 3, /* size value (32MByte) */
+ 0}, /* ECC disabled */
+ { 0xff, /* terminator */
+ 0xff,
+ 0xff,
+ 0xff,
+ 0xff,
+ 0xff,
+ 0xff,
+ 0xff }
+};
+#else
const sdram_t sdram_table[] = {
{ 0x0f, /* Rev A, 128MByte -1 Board */
3, /* Case Latenty = 3 */
3, /* trp 20ns / 7.5 ns datain[27] */
- 3, /* trcd 20ns /7.5 ns (datain[29]) */
- 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
4, /* tcpt 44 - 20ns = 24ns */
- 3, /* Address Mode = 3 */
+ 3, /* Address Mode = 3 */
5, /* size value */
1}, /* ECC enabled */
{ 0x07, /* Rev A, 64MByte -2 Board */
3, /* Case Latenty = 3 */
3, /* trp 20ns / 7.5 ns datain[27] */
- 3, /* trcd 20ns /7.5 ns (datain[29]) */
- 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
4, /* tcpt 44 - 20ns = 24ns */
- 2, /* Address Mode = 2 */
+ 2, /* Address Mode = 2 */
4, /* size value */
1}, /* ECC enabled */
+ { 0x03, /* Rev A, 128MByte -4 Board */
+ 3, /* Case Latenty = 3 */
+ 3, /* trp 20ns / 7.5 ns datain[27] */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 4, /* tcpt 44 - 20ns = 24ns */
+ 3, /* Address Mode = 3 */
+ 5, /* size value */
+ 1}, /* ECC enabled */
+ { 0x1f, /* Rev B, 128MByte -3 Board */
+ 3, /* Case Latenty = 3 */
+ 3, /* trp 20ns / 7.5 ns datain[27] */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 4, /* tcpt 44 - 20ns = 24ns */
+ 3, /* Address Mode = 3 */
+ 5, /* size value */
+ 1}, /* ECC enabled */
+ { 0x2f, /* Rev C, 128MByte -3 Board */
+ 3, /* Case Latenty = 3 */
+ 3, /* trp 20ns / 7.5 ns datain[27] */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 4, /* tcpt 44 - 20ns = 24ns */
+ 3, /* Address Mode = 3 */
+ 5, /* size value */
+ 1}, /* ECC enabled */
{ 0xff, /* terminator */
0xff,
0xff,
0xff,
0xff }
};
-
+#endif /*CONFIG_MIP405T */
void SDRAM_err (const char *s)
{
#ifndef SDRAM_DEBUG
- DECLARE_GLOBAL_DATA_PTR;
-
(void) get_clocks ();
gd->baudrate = 9600;
serial_init ();
int init_sdram (void)
{
- DECLARE_GLOBAL_DATA_PTR;
-
unsigned long tmp, baseaddr;
unsigned short i;
unsigned char trp_clocks,
tctp_clocks;
unsigned char cal_val;
unsigned char bc;
- unsigned long pbcr, sdram_tim, sdram_bank;
- unsigned long *p;
+ unsigned long sdram_tim, sdram_bank;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ /*i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);*/
(void) get_clocks ();
gd->baudrate = 9600;
serial_init ();
- serial_puts ("\nInitializing SDRAM, Please stand by");
- mtdcr (ebccfga, pb0cr); /* get cs0 config reg */
- pbcr = mfdcr (ebccfgd);
- if ((pbcr & 0x00002000) == 0) {
- /* MPS Boot, set up the flash */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, FLASH_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, FLASH_CR);
- } else {
- /* Flash boot, set up the MPS */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, MPS_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, MPS_CR);
- }
- /* set up UART0 (CS2) and UART1 (CS3) */
- mtdcr (ebccfga, pb2ap);
- mtdcr (ebccfgd, UART0_AP);
- mtdcr (ebccfga, pb2cr);
- mtdcr (ebccfgd, UART0_CR);
- mtdcr (ebccfga, pb3ap);
- mtdcr (ebccfgd, UART1_AP);
- mtdcr (ebccfga, pb3cr);
- mtdcr (ebccfgd, UART1_CR);
-
/* set up the pld */
- mtdcr (ebccfga, pb7ap);
- mtdcr (ebccfgd, PLD_AP);
- mtdcr (ebccfga, pb7cr);
- mtdcr (ebccfgd, PLD_CR);
- /* set up the board rev reg */
- mtdcr (ebccfga, pb5ap);
- mtdcr (ebccfgd, BOARD_AP);
- mtdcr (ebccfga, pb5cr);
- mtdcr (ebccfgd, BOARD_CR);
-
-
+ mtdcr (EBC0_CFGADDR, PB7AP);
+ mtdcr (EBC0_CFGDATA, PLD_AP);
+ mtdcr (EBC0_CFGADDR, PB7CR);
+ mtdcr (EBC0_CFGDATA, PLD_CR);
+ /* THIS IS OBSOLETE */
+ /* set up the board rev reg*/
+ mtdcr (EBC0_CFGADDR, PB5AP);
+ mtdcr (EBC0_CFGDATA, BOARD_AP);
+ mtdcr (EBC0_CFGADDR, PB5CR);
+ mtdcr (EBC0_CFGDATA, BOARD_CR);
#ifdef SDRAM_DEBUG
- out8 (PER_BOARD_ADDR, 0);
- bc = in8 (PER_BOARD_ADDR);
- serial_puts ("\nBoard Rev: ");
+ /* get all informations from PLD */
+ serial_puts ("\nPLD Part 0x");
+ bc = in8 (PLD_PART_REG);
write_hex (bc);
- serial_puts (" (PLD=");
+ serial_puts ("\nPLD Vers 0x");
+ bc = in8 (PLD_VERS_REG);
+ write_hex (bc);
+ serial_puts ("\nBoard Rev 0x");
bc = in8 (PLD_BOARD_CFG_REG);
write_hex (bc);
- serial_puts (")\n");
+ serial_puts ("\n");
#endif
- bc = get_board_revcfg ();
+ /* check board */
+ bc = in8 (PLD_PART_REG);
+#if defined(CONFIG_MIP405T)
+ if((bc & 0x80)==0)
+ SDRAM_err ("U-Boot configured for a MIP405T not for a MIP405!!!\n");
+#else
+ if((bc & 0x80)==0x80)
+ SDRAM_err ("U-Boot configured for a MIP405 not for a MIP405T!!!\n");
+#endif
+ /* set-up the chipselect machine */
+ mtdcr (EBC0_CFGADDR, PB0CR); /* get cs0 config reg */
+ tmp = mfdcr (EBC0_CFGDATA);
+ if ((tmp & 0x00002000) == 0) {
+ /* MPS Boot, set up the flash */
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, FLASH_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, FLASH_CR);
+ } else {
+ /* Flash boot, set up the MPS */
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, MPS_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, MPS_CR);
+ }
+ /* set up UART0 (CS2) and UART1 (CS3) */
+ mtdcr (EBC0_CFGADDR, PB2AP);
+ mtdcr (EBC0_CFGDATA, UART0_AP);
+ mtdcr (EBC0_CFGADDR, PB2CR);
+ mtdcr (EBC0_CFGDATA, UART0_CR);
+ mtdcr (EBC0_CFGADDR, PB3AP);
+ mtdcr (EBC0_CFGDATA, UART1_AP);
+ mtdcr (EBC0_CFGADDR, PB3CR);
+ mtdcr (EBC0_CFGDATA, UART1_CR);
+ bc = in8 (PLD_BOARD_CFG_REG);
#ifdef SDRAM_DEBUG
serial_puts ("\nstart SDRAM Setup\n");
serial_puts ("\nBoard Rev: ");
serial_puts ("\n");
#endif
i = 0;
- baseaddr = CFG_SDRAM_BASE;
+ baseaddr = CONFIG_SYS_SDRAM_BASE;
while (sdram_table[i].sz != 0xff) {
if (sdram_table[i].boardtype == bc)
break;
write_hex (i);
serial_puts (" \n");
#endif
+ /* since the ECC initialisation needs some time,
+ * we show that we're alive
+ */
+ if (sdram_table[i].ecc)
+ serial_puts ("\nInitializing SDRAM, Please stand by");
cal_val = sdram_table[i].cal - 1; /* Cas Latency */
trp_clocks = sdram_table[i].trp; /* 20ns / 7.5 ns datain[27] */
trcd_clocks = sdram_table[i].trcd; /* 20ns /7.5 ns (datain[29]) */
/* trc_clocks is sum of trp_clocks + tras_clocks */
trc_clocks = trp_clocks + tras_clocks;
/* get SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- sdram_tim = mfdcr (memcfgd) & ~0x018FC01F;
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
+ sdram_tim = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
/* insert CASL value */
sdram_tim |= ((unsigned long) (cal_val)) << 23;
/* insert PTA value */
/* insert SZ value; */
tmp |= ((unsigned long) sdram_table[i].sz << 17);
/* get SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- sdram_bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
+ sdram_bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
sdram_bank |= (baseaddr | tmp | 0x01);
#ifdef SDRAM_DEBUG
#endif
/* write SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- mtdcr (memcfgd, sdram_tim);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
+ mtdcr (SDRAM0_CFGDATA, sdram_tim);
#ifdef SDRAM_DEBUG
serial_puts ("mb0cf: ");
#endif
/* write SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- mtdcr (memcfgd, sdram_bank);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
+ mtdcr (SDRAM0_CFGDATA, sdram_bank);
if (get_bus_freq (tmp) > 110000000) { /* > 110MHz */
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x07F00000;
} else {
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x05F00000;
}
/* write SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
+ mtdcr (SDRAM0_CFGDATA, tmp);
/* enable ECC if used */
-#if 1
+#if defined(ENABLE_ECC) && !defined(CONFIG_BOOT_PCI)
if (sdram_table[i].ecc) {
/* disable checking for all banks */
+ unsigned long *p;
#ifdef SDRAM_DEBUG
serial_puts ("disable ECC.. ");
#endif
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp &= 0xff0fffff; /* disable all banks */
- mtdcr (memcfga, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
/* set up SDRAM Controller with ECC enabled */
#ifdef SDRAM_DEBUG
serial_puts ("setup SDRAM Controller.. ");
#endif
- mtdcr (memcfgd, tmp);
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (600);
#ifdef SDRAM_DEBUG
serial_puts ("fill the memory..\n");
*p++ = 0L;
if (!((unsigned long) p % 0x00800000)) /* every 8MByte */
serial_puts (".");
-
-
}
/* enable bank 0 */
serial_puts (".");
serial_puts ("enable ECC\n");
#endif
udelay (400);
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp |= 0x00800000; /* enable bank 0 */
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
} else
#endif
{
/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80C00000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80C00000;
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
}
serial_puts ("\n");
return (0);
}
-int board_pre_init (void)
+int board_early_init_f (void)
{
init_sdram ();
| caused the interrupt.
|
+-------------------------------------------------------------------------*/
- mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr (uicer, 0x00000000); /* disable all ints */
- mtdcr (uiccr, 0x00000000); /* set all to be non-critical (for now) */
- mtdcr (uicpr, 0xFFFFFF80); /* set int polarities */
- mtdcr (uictr, 0x10000000); /* set int trigger levels */
- mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
- mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
+ mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr (UIC0ER, 0x00000000); /* disable all ints */
+ mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical (for now) */
+ mtdcr (UIC0PR, 0xFFFFFF80); /* set int polarities */
+ mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
+ mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
+ mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
return 0;
}
}
-
void user_led0 (unsigned char on)
{
if (on)
/* ------------------------------------------------------------------------- */
+void get_pcbrev_var(unsigned char *pcbrev, unsigned char *var)
+{
+#if !defined(CONFIG_MIP405T)
+ unsigned char bc,rc,tmp;
+ int i;
+
+ bc = in8 (PLD_BOARD_CFG_REG);
+ tmp = ~bc;
+ tmp &= 0xf;
+ rc = 0;
+ for (i = 0; i < 4; i++) {
+ rc <<= 1;
+ rc += (tmp & 0x1);
+ tmp >>= 1;
+ }
+ rc++;
+ if(( (((bc>>4) & 0xf)==0x2) /* Rev C PCB or */
+ || (((bc>>4) & 0xf)==0x1)) /* Rev B PCB with */
+ && (rc==0x1)) /* Population Option 1 is a -3 */
+ rc=3;
+ *pcbrev=(bc >> 4) & 0xf;
+ *var=rc;
+#else
+ unsigned char bc;
+ bc = in8 (PLD_BOARD_CFG_REG);
+ *pcbrev=(bc >> 4) & 0xf;
+ *var=16-(bc & 0xf);
+#endif
+}
+
/*
* Check Board Identity:
*/
+/* serial String: "MIP405_1000" OR "MIP405T_1000" */
+#if !defined(CONFIG_MIP405T)
+#define BOARD_NAME "MIP405"
+#else
+#define BOARD_NAME "MIP405T"
+#endif
int checkboard (void)
{
- unsigned char s[50];
- unsigned char bc, var, rc;
+ char s[50];
+ unsigned char bc, var;
int i;
backup_t *b = (backup_t *) s;
puts ("Board: ");
-
- bc = get_board_revcfg ();
- var = ~bc;
- var &= 0xf;
- rc = 0;
- for (i = 0; i < 4; i++) {
- rc <<= 1;
- rc += (var & 0x1);
- var >>= 1;
- }
- rc++;
- i = getenv_r ("serial#", s, 32);
- if ((i == 0) || strncmp (s, "MIP405", 6)) {
+ get_pcbrev_var(&bc,&var);
+ i = getenv_r ("serial#", (char *)s, 32);
+ if ((i == 0) || strncmp ((char *)s, BOARD_NAME,sizeof(BOARD_NAME))) {
get_backup_values (b);
if (strncmp (b->signature, "MPL\0", 4) != 0) {
- puts ("### No HW ID - assuming MIP405");
- printf ("-%d Rev %c", rc, 'A' + ((bc >> 4) & 0xf));
+ puts ("### No HW ID - assuming " BOARD_NAME);
+ printf ("-%d Rev %c", var, 'A' + bc);
} else {
- b->serial_name[6] = 0;
- printf ("%s-%d Rev %c SN: %s", b->serial_name, rc,
- 'A' + ((bc >> 4) & 0xf), &b->serial_name[7]);
+ b->serial_name[sizeof(BOARD_NAME)-1] = 0;
+ printf ("%s-%d Rev %c SN: %s", b->serial_name, var,
+ 'A' + bc, &b->serial_name[sizeof(BOARD_NAME)]);
}
} else {
- s[6] = 0;
- printf ("%s-%d Rev %c SN: %s", s, rc, 'A' + ((bc >> 4) & 0xf),
- &s[7]);
+ s[sizeof(BOARD_NAME)-1] = 0;
+ printf ("%s-%d Rev %c SN: %s", s, var,'A' + bc,
+ &s[sizeof(BOARD_NAME)]);
}
bc = in8 (PLD_EXT_CONF_REG);
printf (" Boot Config: 0x%x\n", bc);
/* ------------------------------------------------------------------------- */
static int test_dram (unsigned long ramsize);
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
unsigned long bank_reg[4], tmp, bank_size;
ds = 0;
/* since the DRAM controller is allready set up, calculate the size with the
bank registers */
- mtdcr (memcfga, mem_mb0cf);
- bank_reg[0] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb1cf);
- bank_reg[1] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb2cf);
- bank_reg[2] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb3cf);
- bank_reg[3] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
+ bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
+ bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
+ bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
+ bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
TotalSize = 0;
for (i = 0; i < 4; i++) {
if ((bank_reg[i] & 0x1) == 0x1) {
} else
ds = 1;
}
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (!tmp)
printf ("No ");
/* ------------------------------------------------------------------------- */
-extern int mem_test (unsigned long start, unsigned long ramsize,
- int quiet);
static int test_dram (unsigned long ramsize)
{
return (1);
}
+/* used to check if the time in RTC is valid */
+static unsigned long start;
+static struct rtc_time tm;
+extern flash_info_t flash_info[]; /* info for FLASH chips */
+
int misc_init_r (void)
{
+ /* adjust flash start and size as well as the offset */
+ gd->bd->bi_flashstart=0-flash_info[0].size;
+ gd->bd->bi_flashsize=flash_info[0].size-CONFIG_SYS_MONITOR_LEN;
+ gd->bd->bi_flashoffset=0;
+
+ /* check, if RTC is running */
+ rtc_get (&tm);
+ start=get_timer(0);
+ /* if MIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
+ if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
+ mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
+
return (0);
}
void print_mip405_rev (void)
{
- unsigned char part, vers, cfg, rev;
-
- cfg = get_board_revcfg ();
- vers = cfg;
- vers &= 0xf;
- rev = (((vers & 0x1) ? 0x8 : 0) |
- ((vers & 0x2) ? 0x4 : 0) |
- ((vers & 0x4) ? 0x2 : 0) | ((vers & 0x8) ? 0x1 : 0));
+ unsigned char part, vers, pcbrev, var;
+ get_pcbrev_var(&pcbrev,&var);
part = in8 (PLD_PART_REG);
vers = in8 (PLD_VERS_REG);
- printf ("Rev: MIP405-%d Rev %c PLD%d Vers %d\n",
- (16 - rev), ((cfg >> 4) & 0xf) + 'A', part, vers);
+ printf ("Rev: " BOARD_NAME "-%d Rev %c PLD %d Vers %d\n",
+ var, pcbrev + 'A', part & 0x7F, vers);
}
+extern int mk_date (char *, struct rtc_time *);
+
int last_stage_init (void)
{
- if (miiphy_write (0x1, 0x14, 0x2402) != 0) {
+ unsigned long stop;
+ struct rtc_time newtm;
+ char *s;
+
+ /* write correct LED configuration */
+ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x14, 0x2402) != 0) {
+ printf ("Error writing to the PHY\n");
+ }
+ /* since LED/CFG2 is not connected on the -2,
+ * write to correct capability information */
+ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x4, 0x01E1) != 0) {
printf ("Error writing to the PHY\n");
}
print_mip405_rev ();
- show_stdio_dev ();
+ stdio_print_current_devices ();
check_env ();
+ /* check if RTC time is valid */
+ stop=get_timer(start);
+ while(stop<1200) { /* we wait 1.2 sec to check if the RTC is running */
+ udelay(1000);
+ stop=get_timer(start);
+ }
+ rtc_get (&newtm);
+ if(tm.tm_sec==newtm.tm_sec) {
+ s=getenv("defaultdate");
+ if(!s)
+ mk_date ("010112001970", &newtm);
+ else
+ if(mk_date (s, &newtm)!=0) {
+ printf("RTC: Bad date format in defaultdate\n");
+ return 0;
+ }
+ rtc_reset ();
+ rtc_set(&newtm);
+ }
return 0;
}
com_mode = in8 (PLD_COM_MODE_REG);
ext = in8 (PLD_EXT_CONF_REG);
- printf ("PLD Part %d version %d\n", part, vers);
+ printf ("PLD Part %d version %d\n", part & 0x7F, vers);
printf ("Board Revision %c\n", ((cfg >> 4) & 0xf) + 'A');
printf ("Population Options %d %d %d %d\n", (cfg) & 0x1,
(cfg >> 1) & 0x1, (cfg >> 2) & 0x1, (cfg >> 3) & 0x1);
printf ("User LED %s\n", (com_mode & 0x4) ? "on" : "off");
printf ("UART Clocks %d\n", (com_mode >> 4) & 0x3);
- printf ("Test ist %x\n", com_mode);
+#if !defined(CONFIG_MIP405T)
printf ("User Config Switch %d %d %d %d %d %d %d %d\n",
(ext) & 0x1, (ext >> 1) & 0x1, (ext >> 2) & 0x1,
(ext >> 3) & 0x1, (ext >> 4) & 0x1, (ext >> 5) & 0x1,
(ext >> 6) & 0x1, (ext >> 7) & 0x1);
printf ("SER1 uses handshakes %s\n",
(ext & 0x80) ? "DTR/DSR" : "RTS/CTS");
+#else
+ printf ("User Config Switch %d %d %d %d %d %d %d %d\n",
+ (ext) & 0x1, (ext >> 1) & 0x1, (ext >> 2) & 0x1,
+ (ext >> 3) & 0x1, (ext >> 4) & 0x1, (ext >> 5) & 0x1,
+ (ext >> 6) & 0x1,(ext >> 7) & 0x1);
+#endif
printf ("IDE Reset %s\n", (ext & 0x01) ? "asserted" : "not asserted");
printf ("IRQs:\n");
printf (" PIIX INTR: %s\n", (irq_reg & 0x80) ? "inactive" : "active");
+#if !defined(CONFIG_MIP405T)
printf (" UART0 IRQ: %s\n", (irq_reg & 0x40) ? "inactive" : "active");
printf (" UART1 IRQ: %s\n", (irq_reg & 0x20) ? "inactive" : "active");
+#endif
printf (" PIIX SMI: %s\n", (irq_reg & 0x10) ? "inactive" : "active");
printf (" PIIX INIT: %s\n", (irq_reg & 0x8) ? "inactive" : "active");
printf (" PIIX NMI: %s\n", (irq_reg & 0x4) ? "inactive" : "active");
}
-
-
projects / platform / kernel / u-boot.git / blobdiff