#include <asm/io.h>
#include <asm/ppc4xx-uic.h>
#include <asm/processor.h>
+#include <asm/4xx_pci.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Assign interrupts to PCI devices.
*/
-void korat_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
#endif
/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#if defined(CONFIG_PCI_PNP)
- hose->fixup_irq = korat_pci_fixup_irq;
-#endif
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
* pci_target_init
*
* The bootstrap configuration provides default settings for the pci
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0x80000000-0xBFFFFFFF
- * ==> PCI address 0x80000000-0xBFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA,
- CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIX0_PMM1LA,
- CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA,
- CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+ /* First do 440EP(x) common setup */
+ __pci_target_init(hose);
/*
* Set up Configuration registers for on-board NEC uPD720101 USB
}
#endif
-/*
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- */
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Korat is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
-
#if defined(CONFIG_POST)
/*
* Returns 1 if keys pressed to start the power-on long-running tests
projects / platform / kernel / u-boot.git / blobdiff