* (C) Copyright 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
MPP4_NF_IO6,
MPP5_NF_IO7,
MPP6_SYSRST_OUTn,
+#if defined(KM_PCIE_RESET_MPP7)
+ MPP7_GPO,
+#else
MPP7_PEX_RST_OUTn,
-#if defined(CONFIG_SOFT_I2C)
+#endif
+#if defined(CONFIG_SYS_I2C_SOFT)
MPP8_GPIO, /* SDA */
MPP9_GPIO, /* SCL */
#endif
/*
* Wait for startup OK from mgcoge3ne
*/
-int startup_allowed(void)
+static int startup_allowed(void)
{
unsigned char buf;
}
#endif
-int initialize_unit_leds(void)
+static int initialize_unit_leds(void)
{
/*
* Init the unit LEDs per default they all are
return 0;
}
-#if defined(CONFIG_BOOTCOUNT_LIMIT)
-void set_bootcount_addr(void)
+static void set_bootcount_addr(void)
{
uchar buf[32];
unsigned int bootcountaddr;
sprintf((char *)buf, "0x%x", bootcountaddr);
setenv("bootcountaddr", (char *)buf);
}
-#endif
int misc_init_r(void)
{
initialize_unit_leds();
set_km_env();
-#if defined(CONFIG_BOOTCOUNT_LIMIT)
set_bootcount_addr();
-#endif
return 0;
}
int board_early_init_f(void)
{
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
u32 tmp;
/* set the 2 bitbang i2c pins as output gpios */
kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1);
kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1);
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
/*
* Reinit the GPIO for I2C Bitbang driver so that the now
* available gpio framework is consistent. The calls to
return;
/* RGMII clk transition on data stable */
- if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®))
+ if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®))
printf("Error reading PHY spec ctrl reg\n");
- if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
- reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
+ if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
+ reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
printf("Error writing PHY spec ctrl reg\n");
/* leds setup */
- if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
- PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
+ if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
+ PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
printf("Error writing PHY LED reg\n");
/* reset the phy */
#if defined(CONFIG_KM_NUSA)
struct mv88e_sw_reg extsw_conf[] = {
/*
- * port 0, PIGGY4, autoneg
+ * port 0, PIGGY4, autoneg
* first the fix for the 1000Mbits Autoneg, this is from
* a Marvell errata, the regs are undocumented
*/
}
#endif
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
void set_sda(int state)
{
I2C_ACTIVE;