+// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2006 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
*
* (C) Copyright 2008 - 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <env.h>
+#include <fdt_support.h>
+#include <init.h>
#include <ioports.h>
+#include <log.h>
#include <mpc83xx.h>
#include <i2c.h>
#include <miiphy.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <pci.h>
-#include <libfdt.h>
+#include <linux/delay.h>
+#include <linux/libfdt.h>
#include <post.h>
#include "../common/common.h"
static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
-const qe_iop_conf_t qe_iop_conf_tab[] = {
- /* port pin dir open_drain assign */
-#if defined(CONFIG_MPC8360)
- /* MDIO */
- {0, 1, 3, 0, 2}, /* MDIO */
- {0, 2, 1, 0, 1}, /* MDC */
-
- /* UCC4 - UEC */
- {1, 14, 1, 0, 1}, /* TxD0 */
- {1, 15, 1, 0, 1}, /* TxD1 */
- {1, 20, 2, 0, 1}, /* RxD0 */
- {1, 21, 2, 0, 1}, /* RxD1 */
- {1, 18, 1, 0, 1}, /* TX_EN */
- {1, 26, 2, 0, 1}, /* RX_DV */
- {1, 27, 2, 0, 1}, /* RX_ER */
- {1, 24, 2, 0, 1}, /* COL */
- {1, 25, 2, 0, 1}, /* CRS */
- {2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */
- {2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */
-
- /* DUART - UART2 */
- {5, 0, 1, 0, 2}, /* UART2_SOUT */
- {5, 2, 1, 0, 1}, /* UART2_RTS */
- {5, 3, 2, 0, 2}, /* UART2_SIN */
- {5, 1, 2, 0, 3}, /* UART2_CTS */
-#elif !defined(CONFIG_MPC8309)
- /* Local Bus */
- {0, 16, 1, 0, 3}, /* LA00 */
- {0, 17, 1, 0, 3}, /* LA01 */
- {0, 18, 1, 0, 3}, /* LA02 */
- {0, 19, 1, 0, 3}, /* LA03 */
- {0, 20, 1, 0, 3}, /* LA04 */
- {0, 21, 1, 0, 3}, /* LA05 */
- {0, 22, 1, 0, 3}, /* LA06 */
- {0, 23, 1, 0, 3}, /* LA07 */
- {0, 24, 1, 0, 3}, /* LA08 */
- {0, 25, 1, 0, 3}, /* LA09 */
- {0, 26, 1, 0, 3}, /* LA10 */
- {0, 27, 1, 0, 3}, /* LA11 */
- {0, 28, 1, 0, 3}, /* LA12 */
- {0, 29, 1, 0, 3}, /* LA13 */
- {0, 30, 1, 0, 3}, /* LA14 */
- {0, 31, 1, 0, 3}, /* LA15 */
-
- /* MDIO */
- {3, 4, 3, 0, 2}, /* MDIO */
- {3, 5, 1, 0, 2}, /* MDC */
-
- /* UCC4 - UEC */
- {1, 18, 1, 0, 1}, /* TxD0 */
- {1, 19, 1, 0, 1}, /* TxD1 */
- {1, 22, 2, 0, 1}, /* RxD0 */
- {1, 23, 2, 0, 1}, /* RxD1 */
- {1, 26, 2, 0, 1}, /* RxER */
- {1, 28, 2, 0, 1}, /* Rx_DV */
- {1, 30, 1, 0, 1}, /* TxEN */
- {1, 31, 2, 0, 1}, /* CRS */
- {3, 10, 2, 0, 3}, /* TxCLK->CLK17 */
-#endif
-
- /* END of table */
- {0, 0, 0, 0, QE_IOP_TAB_END},
-};
-
-#if defined(CONFIG_SUVD3)
-const uint upma_table[] = {
- 0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */
- 0x0ffcdc00, 0xffffcc00, 0xffffcc01, 0xfffffc01, /* Words 4 to 7 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 8 to 11 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 12 to 15 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 16 to 19 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 20 to 23 */
- 0x9cfffc00, 0x00fffc80, 0x00fffc80, 0x00fffc00, /* Words 24 to 27 */
- 0xffffec04, 0xffffec01, 0xfffffc01, 0xfffffc01, /* Words 28 to 31 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 32 to 35 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 36 to 39 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 40 to 43 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 44 to 47 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 48 to 51 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 52 to 55 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 56 to 59 */
- 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01 /* Words 60 to 63 */
-};
-#endif
-
static int piggy_present(void)
{
struct km_bec_fpga __iomem *base =
return in_8(&base->bprth) & PIGGY_PRESENT;
}
-#if defined(CONFIG_KMVECT1)
-int ethernet_present(void)
-{
- /* ethernet port connected to simple switch without piggy */
- return 1;
-}
-#else
int ethernet_present(void)
{
return piggy_present();
}
-#endif
-
int board_early_init_r(void)
{
struct km_bec_fpga *base =
(struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
-#if defined(CONFIG_SUVD3)
- immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- fsl_lbc_t *lbc = &immap->im_lbc;
- u32 *mxmr = &lbc->mamr;
-#endif
-#if defined(CONFIG_MPC8360)
+#if defined(CONFIG_ARCH_MPC8360)
unsigned short svid;
/*
* Because of errata in the UCCs, we have to write to the reserved
/* enable Application Buffer */
setbits_8(&base->oprtl, OPRTL_XBUFENA);
-#if defined(CONFIG_SUVD3)
- /* configure UPMA for APP1 */
- upmconfig(UPMA, (uint *) upma_table,
- sizeof(upma_table) / sizeof(uint));
- out_be32(mxmr, CONFIG_SYS_MAMR);
-#endif
return 0;
}
int misc_init_r(void)
{
- ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
+ ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
+ CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
return 0;
}
-#if defined(CONFIG_KMVECT1)
-#include <mv88e6352.h>
-/* Marvell MV88E6122 switch configuration */
-static struct mv88e_sw_reg extsw_conf[] = {
- /* port 1, FRONT_MDI, autoneg */
- { PORT(1), PORT_PHY, NO_SPEED_FOR },
- { PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- { PHY(1), PHY_1000_CTRL, NO_ADV },
- { PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN },
- { PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
- FULL_DUPLEX },
- /* port 2, unused */
- { PORT(2), PORT_CTRL, PORT_DIS },
- { PHY(2), PHY_CTRL, PHY_PWR_DOWN },
- { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
- /* port 3, BP_MII (CPU), PHY mode, 100BASE */
- { PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- /* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */
- { PORT(4), PORT_STATUS, NO_PHY_DETECT },
- { PORT(4), PORT_PHY, SPEED_1000_FOR },
- { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- /* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */
- { PORT(5), PORT_STATUS, NO_PHY_DETECT },
- { PORT(5), PORT_PHY, SPEED_1000_FOR },
- { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- /*
- * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
- * acc . MV-S300889-00D.pdf , clause 4.5
- */
- { PORT(5), 0x1A, 0xADB1 },
- /* port 6, unused, this port has no phy */
- { PORT(6), PORT_CTRL, PORT_DIS },
- /*
- * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
- * acc . MV-S300889-00D.pdf , clause 4.5
- */
- { PORT(5), 0x1A, 0xADB1 },
-};
-#endif
-
int last_stage_init(void)
{
-#if defined(CONFIG_KMVECT1)
- struct km_bec_fpga __iomem *base =
- (struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE;
- u8 tmp_reg;
-
- /* Release mv88e6122 from reset */
- tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */
- out_8(&base->res1[0], tmp_reg); /* GP28 as output */
- tmp_reg = in_8(&base->gprt3) | 0x10; /* GP28 to high */
- out_8(&base->gprt3, tmp_reg);
-
- /* configure MV88E6122 switch */
- char *name = "UEC2";
-
- if (miiphy_set_current_dev(name))
- return 0;
-
- mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
- ARRAY_SIZE(extsw_conf));
-
- mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
-
- if (piggy_present()) {
- setenv("ethact", "UEC2");
- setenv("netdev", "eth1");
- puts("using PIGGY for network boot\n");
- } else {
- setenv("netdev", "eth0");
- puts("using frontport for network boot\n");
- }
-#endif
-
-#if defined(CONFIG_KMCOGE5NE)
+#if defined(CONFIG_TARGET_KMCOGE5NE)
struct bfticu_iomap *base =
(struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE;
u8 dip_switch = in_8((u8 *)&(base->mswitch)) & BFTICU_DIPSWITCH_MASK;
if (dip_switch != 0) {
/* start bootloader */
puts("DIP: Enabled\n");
- setenv("actual_bank", "0");
+ env_set("actual_bank", "0");
}
#endif
set_km_env();
msize = CONFIG_SYS_DDR_SIZE << 20;
disable_addr_trans();
- msize = get_ram_size(CONFIG_SYS_DDR_BASE, msize);
+ msize = get_ram_size(CONFIG_SYS_SDRAM_BASE, msize);
enable_addr_trans();
msize /= (1024 * 1024);
if (CONFIG_SYS_DDR_SIZE != msize) {
return msize;
}
-int initdram(void)
+int dram_init(void)
{
immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
u32 msize = 0;
return -ENXIO;
out_be32(&im->sysconf.ddrlaw[0].bar,
- CONFIG_SYS_DDR_BASE & LAWBAR_BAR);
+ CONFIG_SYS_SDRAM_BASE & LAWBAR_BAR);
msize = fixed_sdram();
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
int checkboard(void)
{
- puts("Board: Keymile " CONFIG_KM_BOARD_NAME);
+ puts("Board: Hitachi " CONFIG_SYS_CONFIG_NAME);
if (piggy_present())
puts(" with PIGGY.");
return 0;
}
-int ft_board_setup(void *blob, bd_t *bd)
+int ft_board_setup(void *blob, struct bd_info *bd)
{
ft_cpu_setup(blob, bd);