board/freescale: Remove P1025RDB board support

[platform/kernel/u-boot.git] / board / freescale / p1_p2_rdb_pc / p1_p2_rdb_pc.c

diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
index ba12bea..2005944 100644 (file)
--- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
@@ -53,7 +53,7 @@
 #define GPIO_2BIT_MASK         (0x3 << (32 - (GPIO_DDR_RST_PIN + 1) * 2))
 #endif
 
-#if defined(CONFIG_TARGET_P1025RDB) || defined(CONFIG_TARGET_P1021RDB)
+#if defined(CONFIG_TARGET_P1021RDB)
 #define PCA_IOPORT_I2C_ADDR            0x23
 #define PCA_IOPORT_OUTPUT_CMD          0x2
 #define PCA_IOPORT_CFG_CMD             0x6
@@ -70,43 +70,6 @@ const qe_iop_conf_t qe_iop_conf_tab[] = {
        {0,  15, 1, 0, 0}, /* GPIO11/A15  - WDI */
        {GPIO_GETH_SW_PORT, GPIO_GETH_SW_PIN, 1, 0, 0}, /* RST_GETH_SW_N */
        {GPIO_SLIC_PORT, GPIO_SLIC_PIN, 1, 0, 0},       /* RST_SLIC_N */
-
-#ifdef CONFIG_TARGET_P1025RDB
-       /* QE_MUX_MDC */
-       {1,  19, 1, 0, 1}, /* QE_MUX_MDC               */
-
-       /* QE_MUX_MDIO */
-       {1,  20, 3, 0, 1}, /* QE_MUX_MDIO              */
-
-       /* UCC_1_MII */
-       {0, 23, 2, 0, 2}, /* CLK12 */
-       {0, 24, 2, 0, 1}, /* CLK9 */
-       {0,  7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0      */
-       {0,  9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1      */
-       {0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2      */
-       {0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3      */
-       {0,  6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0      */
-       {0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1      */
-       {0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2      */
-       {0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3      */
-       {0,  5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B    */
-       {0, 13, 1, 0, 2}, /* ENET1_TX_ER               */
-       {0,  4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B    */
-       {0,  8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B    */
-       {0, 17, 2, 0, 2}, /* ENET1_CRS    */
-       {0, 16, 2, 0, 2}, /* ENET1_COL    */
-
-       /* UCC_5_RMII */
-       {1, 11, 2, 0, 1}, /* CLK13 */
-       {1, 7,  1, 0, 2}, /* ENET5_TXD0_SER5_TXD0      */
-       {1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1      */
-       {1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0      */
-       {1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1      */
-       {1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B    */
-       {1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B    */
-       {1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B    */
-#endif
-
        {0,  0, 0, 0, QE_IOP_TAB_END} /* END of table */
 };
 #endif
@@ -410,7 +373,7 @@ int board_eth_init(struct bd_info *bis)
 #endif
 
 #if defined(CONFIG_QE) && \
-       (defined(CONFIG_TARGET_P1025RDB) || defined(CONFIG_TARGET_P1021RDB))
+       (defined(CONFIG_TARGET_P1021RDB))
 static void fdt_board_fixup_qe_pins(void *blob)
 {
        unsigned int oldbus;
@@ -481,7 +444,7 @@ int ft_board_setup(void *blob, struct bd_info *bd)
 #ifdef CONFIG_QE
        do_fixup_by_compat(blob, "fsl,qe", "status", "okay",
                        sizeof("okay"), 0);
-#if defined(CONFIG_TARGET_P1025RDB) || defined(CONFIG_TARGET_P1021RDB)
+#if defined(CONFIG_TARGET_P1021RDB)
        fdt_board_fixup_qe_pins(blob);
 #endif
 #endif