+// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <clock_legacy.h>
+#include <init.h>
#include <mpc85xx.h>
#include <asm/io.h>
#include <ns16550.h>
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
-
-void sdram_init(void)
-{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
- u32 ddr_ratio;
- unsigned long ddr_freq_mhz;
-
- ddr_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO;
- ddr_ratio = ddr_ratio >> MPC85xx_PORPLLSR_DDR_RATIO_SHIFT;
- ddr_freq_mhz = (CONFIG_SYS_CLK_FREQ * ddr_ratio) / 1000000;
-
- /* mask off E bit */
- u32 svr = SVR_SOC_VER(mfspr(SPRN_SVR));
-
- __raw_writel(CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE, &ddr->sdram_cfg);
- __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
- __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init);
-
- if (ddr_freq_mhz < 700) {
- __raw_writel(CONFIG_SYS_DDR_TIMING_3_667, &ddr->timing_cfg_3);
- __raw_writel(CONFIG_SYS_DDR_TIMING_0_667, &ddr->timing_cfg_0);
- __raw_writel(CONFIG_SYS_DDR_TIMING_1_667, &ddr->timing_cfg_1);
- __raw_writel(CONFIG_SYS_DDR_TIMING_2_667, &ddr->timing_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_MODE_1_667, &ddr->sdram_mode);
- __raw_writel(CONFIG_SYS_DDR_MODE_2_667, &ddr->sdram_mode_2);
- __raw_writel(CONFIG_SYS_DDR_INTERVAL_667, &ddr->sdram_interval);
- __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_667, &ddr->sdram_clk_cntl);
- __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_667, &ddr->ddr_wrlvl_cntl);
- } else {
- __raw_writel(CONFIG_SYS_DDR_TIMING_3_800, &ddr->timing_cfg_3);
- __raw_writel(CONFIG_SYS_DDR_TIMING_0_800, &ddr->timing_cfg_0);
- __raw_writel(CONFIG_SYS_DDR_TIMING_1_800, &ddr->timing_cfg_1);
- __raw_writel(CONFIG_SYS_DDR_TIMING_2_800, &ddr->timing_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_MODE_1_800, &ddr->sdram_mode);
- __raw_writel(CONFIG_SYS_DDR_MODE_2_800, &ddr->sdram_mode_2);
- __raw_writel(CONFIG_SYS_DDR_INTERVAL_800, &ddr->sdram_interval);
- __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_800, &ddr->sdram_clk_cntl);
- __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_800, &ddr->ddr_wrlvl_cntl);
- }
-
- __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4);
- __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5);
- __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl);
-
- /* P1014 and it's derivatives support max 16bit DDR width */
- if (svr == SVR_P1014) {
- __raw_writel(ddr->sdram_cfg & ~SDRAM_CFG_DBW_MASK, &ddr->sdram_cfg);
- __raw_writel(ddr->sdram_cfg | SDRAM_CFG_16_BE, &ddr->sdram_cfg);
- /* For CS0_BNDS we divide the start and end address by 2, so we can just
- * shift the entire register to achieve the desired result and the mask
- * the value so we don't write reserved fields */
- __raw_writel((CONFIG_SYS_DDR_CS0_BNDS >> 1) & 0x0fff0fff, &ddr->cs0_bnds);
- }
-
- asm volatile("sync;isync");
- udelay(500);
-
- /* Let the controller go */
- out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
-
- set_next_law(CONFIG_SYS_NAND_DDR_LAW, LAW_SIZE_1G, LAW_TRGT_IF_DDR_1);
-}
-
void board_init_f(ulong bootflag)
{
u32 plat_ratio;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+ ccsr_gur_t *gur = (void *)CFG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
+ set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
+#endif
/* initialize selected port with appropriate baud rate */
plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
plat_ratio >>= 1;
- gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+ gd->bus_clk = get_board_sys_clk() * plat_ratio;
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- gd->bus_clk / 16 / CONFIG_BAUDRATE);
+ ns16550_init((struct ns16550 *)CONFIG_SYS_NS16550_COM1,
+ gd->bus_clk / 16 / CONFIG_BAUDRATE);
puts("\nNAND boot... ");
- /* Initialize the DDR3 */
- sdram_init();
-
/* copy code to RAM and jump to it - this should not return */
/* NOTE - code has to be copied out of NAND buffer before
* other blocks can be read.
void board_init_r(gd_t *gd, ulong dest_addr)
{
+ puts("\nSecond program loader running in sram...");
nand_boot();
}
void putc(char c)
{
if (c == '\n')
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+ ns16550_putc((struct ns16550 *)CONFIG_SYS_NS16550_COM1, '\r');
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+ ns16550_putc((struct ns16550 *)CONFIG_SYS_NS16550_COM1, c);
}
void puts(const char *str)
projects / platform / kernel / u-boot.git / blobdiff