#include <asm/errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/crm_regs.h>
+#include <asm/arch/clock.h>
#include <i2c.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <fsl_pmic.h>
#include <mc13892.h>
#include <usb/ehci-fsl.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+
+#define MX51EVK_LCD_3V3 IMX_GPIO_NR(4, 9)
+#define MX51EVK_LCD_5V IMX_GPIO_NR(4, 10)
+#define MX51EVK_LCD_BACKLIGHT IMX_GPIO_NR(3, 4)
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg esdhc_cfg[2] = {
- {MMC_SDHC1_BASE_ADDR, 1},
- {MMC_SDHC2_BASE_ADDR, 1},
+ {MMC_SDHC1_BASE_ADDR},
+ {MMC_SDHC2_BASE_ADDR},
};
#endif
return 0;
}
+u32 get_board_rev(void)
+{
+ u32 rev = get_cpu_rev();
+ if (!gpio_get_value(IMX_GPIO_NR(1, 22)))
+ rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET;
+ return rev;
+}
+
static void setup_iomux_uart(void)
{
unsigned int pad = PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE |
pmic_reg_write(p, REG_MODE_1, val);
mxc_request_iomux(MX51_PIN_EIM_A20, IOMUX_CONFIG_ALT1);
- gpio_direction_output(46, 0);
+ gpio_direction_output(IMX_GPIO_NR(2, 14), 0);
udelay(500);
- gpio_set_value(46, 1);
+ gpio_set_value(IMX_GPIO_NR(2, 14), 1);
}
#ifdef CONFIG_FSL_ESDHC
int ret;
mxc_request_iomux(MX51_PIN_GPIO1_0, IOMUX_CONFIG_ALT1);
- gpio_direction_input(0);
+ gpio_direction_input(IMX_GPIO_NR(1, 0));
mxc_request_iomux(MX51_PIN_GPIO1_6, IOMUX_CONFIG_ALT0);
- gpio_direction_input(6);
+ gpio_direction_input(IMX_GPIO_NR(1, 6));
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
- ret = !gpio_get_value(0);
+ ret = !gpio_get_value(IMX_GPIO_NR(1, 0));
else
- ret = !gpio_get_value(6);
+ ret = !gpio_get_value(IMX_GPIO_NR(1, 6));
return ret;
}
u32 index;
s32 status = 0;
+ esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM;
index++) {
switch (index) {
}
#endif
+static struct fb_videomode const claa_wvga = {
+ .name = "CLAA07LC0ACW",
+ .refresh = 57,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 37037,
+ .left_margin = 40,
+ .right_margin = 60,
+ .upper_margin = 10,
+ .lower_margin = 10,
+ .hsync_len = 20,
+ .vsync_len = 10,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED
+};
+
+void lcd_iomux(void)
+{
+ /* DI2_PIN15 */
+ mxc_request_iomux(MX51_PIN_DI_GP4, IOMUX_CONFIG_ALT4);
+
+ /* Pad settings for MX51_PIN_DI2_DISP_CLK */
+ mxc_iomux_set_pad(MX51_PIN_DI2_DISP_CLK, PAD_CTL_HYS_NONE |
+ PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER |
+ PAD_CTL_DRV_MAX | PAD_CTL_SRE_SLOW);
+
+ /* Turn on 3.3V voltage for LCD */
+ mxc_request_iomux(MX51_PIN_CSI2_D12, IOMUX_CONFIG_ALT3);
+ gpio_direction_output(MX51EVK_LCD_3V3, 1);
+
+ /* Turn on 5V voltage for LCD */
+ mxc_request_iomux(MX51_PIN_CSI2_D13, IOMUX_CONFIG_ALT3);
+ gpio_direction_output(MX51EVK_LCD_5V, 1);
+
+ /* Turn on GPIO backlight */
+ mxc_request_iomux(MX51_PIN_DI1_D1_CS, IOMUX_CONFIG_ALT4);
+ mxc_iomux_set_input(MX51_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT,
+ INPUT_CTL_PATH1);
+ gpio_direction_output(MX51EVK_LCD_BACKLIGHT, 1);
+}
+
+void lcd_enable(void)
+{
+ int ret = ipuv3_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565);
+ if (ret)
+ printf("LCD cannot be configured: %d\n", ret);
+}
+
int board_early_init_f(void)
{
setup_iomux_uart();
#ifdef CONFIG_USB_EHCI_MX5
setup_usb_h1();
#endif
+ lcd_iomux();
return 0;
}
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+ lcd_enable();
+
return 0;
}
setup_iomux_spi();
power_init();
#endif
+
return 0;
}
#endif
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
int checkboard(void)
{
puts("Board: MX51EVK\n");