#endif
void local_bus_init(void);
-void sdram_init(void);
-long int fixed_sdram(void);
int checkboard (void)
{
puts("Board: ADS\n");
#ifdef CONFIG_PCI
- printf(" PCI1: 32 bit, %d MHz (compiled)\n",
+ printf("PCI1: 32 bit, %d MHz (compiled)\n",
CONFIG_SYS_CLK_FREQ / 1000000);
#else
- printf(" PCI1: disabled\n");
+ printf("PCI1: disabled\n");
#endif
/*
return 0;
}
-
-phys_size_t
-initdram(int board_type)
-{
- long dram_size = 0;
-
- puts("Initializing\n");
-
-#if defined(CONFIG_DDR_DLL)
- {
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- uint temp_ddrdll = 0;
-
- /*
- * Work around to stabilize DDR DLL
- */
- temp_ddrdll = gur->ddrdllcr;
- gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
- asm("sync;isync;msync");
- }
-#endif
-
-#ifdef CONFIG_SPD_EEPROM
- dram_size = fsl_ddr_sdram();
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
-
- dram_size *= 0x100000;
-#else
- dram_size = fixed_sdram();
-#endif
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize and enable DDR ECC.
- */
- ddr_enable_ecc(dram_size);
-#endif
-
- /*
- * Initialize SDRAM.
- */
- sdram_init();
-
- puts(" DDR: ");
- return dram_size;
-}
-
-
/*
* Initialize Local Bus
*/
lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
if (lbc_hz < 66) {
- lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000; /* DLL Bypass */
+ lbc->lcrr = CONFIG_SYS_LBC_LCRR | LCRR_DBYP; /* DLL Bypass */
} else if (lbc_hz >= 133) {
- lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */
+ lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */
} else {
/*
lbc->lcrr = 0x10000004;
}
- lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */
+ lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */
udelay(200);
/*
/*
* Initialize SDRAM memory on the Local Bus.
*/
-
-void
-sdram_init(void)
+void lbc_sdram_init(void)
{
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
- puts(" SDRAM: ");
- print_size (CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+ puts("LBC SDRAM: ");
+ print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
+ "\n ");
/*
* Setup SDRAM Base and Option Registers
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
************************************************************************/
-long int fixed_sdram (void)
+phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;