/*
- * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
#include <common.h>
#include <i2c.h>
-
+#include <hwconfig.h>
+#include <asm/mmu.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
-static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
+
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+extern fixed_ddr_parm_t fixed_ddr_parm_0[];
+#if (CONFIG_NUM_DDR_CONTROLLERS == 2)
+extern fixed_ddr_parm_t fixed_ddr_parm_1[];
+#endif
+
+phys_size_t fixed_sdram(void)
{
- int ret;
+ int i;
+ char buf[32];
+ fsl_ddr_cfg_regs_t ddr_cfg_regs;
+ phys_size_t ddr_size;
+ unsigned int lawbar1_target_id;
+ ulong ddr_freq, ddr_freq_mhz;
+
+ ddr_freq = get_ddr_freq(0);
+ ddr_freq_mhz = ddr_freq / 1000000;
- ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
- if (ret) {
- debug("DDR: failed to read SPD from address %u\n", i2c_address);
- memset(spd, 0, sizeof(ddr3_spd_eeprom_t));
+ printf("Configuring DDR for %s MT/s data rate\n",
+ strmhz(buf, ddr_freq));
+
+ for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
+ if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
+ (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
+ memcpy(&ddr_cfg_regs,
+ fixed_ddr_parm_0[i].ddr_settings,
+ sizeof(ddr_cfg_regs));
+ break;
+ }
}
-}
-unsigned int fsl_ddr_get_mem_data_rate(void)
-{
- return get_ddr_freq(0);
-}
+ if (fixed_ddr_parm_0[i].max_freq == 0)
+ panic("Unsupported DDR data rate %s MT/s data rate\n",
+ strmhz(buf, ddr_freq));
-void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
- unsigned int ctrl_num)
-{
- unsigned int i;
- unsigned int i2c_address = 0;
+ ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+ ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
+ fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
- for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
- if (ctrl_num == 0 && i == 0)
- i2c_address = SPD_EEPROM_ADDRESS1;
- else if (ctrl_num == 1 && i == 0)
- i2c_address = SPD_EEPROM_ADDRESS2;
+#if (CONFIG_NUM_DDR_CONTROLLERS == 2)
+ memcpy(&ddr_cfg_regs,
+ fixed_ddr_parm_1[i].ddr_settings,
+ sizeof(ddr_cfg_regs));
+ ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
+ fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 1);
+#endif
- get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+ /*
+ * setup laws for DDR. If not interleaving, presuming half memory on
+ * DDR1 and the other half on DDR2
+ */
+ if (fixed_ddr_parm_0[i].ddr_settings->cs[0].config & 0x20000000) {
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+ ddr_size,
+ LAW_TRGT_IF_DDR_INTRLV) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ }
+ } else {
+#if (CONFIG_NUM_DDR_CONTROLLERS == 2)
+ /* We require both controllers have identical DIMMs */
+ lawbar1_target_id = LAW_TRGT_IF_DDR_1;
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+ ddr_size / 2,
+ lawbar1_target_id) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ }
+ lawbar1_target_id = LAW_TRGT_IF_DDR_2;
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE + ddr_size / 2,
+ ddr_size / 2,
+ lawbar1_target_id) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ }
+#else
+ lawbar1_target_id = LAW_TRGT_IF_DDR_1;
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+ ddr_size,
+ lawbar1_target_id) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ }
+#endif
}
+ return ddr_size;
}
-typedef struct {
- u32 datarate_mhz_low;
- u32 datarate_mhz_high;
+struct board_specific_parameters {
u32 n_ranks;
+ u32 datarate_mhz_high;
u32 clk_adjust;
+ u32 wrlvl_start;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
-} board_specific_parameters_t;
+};
-/* ranges for parameters:
- * wr_data_delay = 0-6
- * clk adjust = 0-8
- * cpo 2-0x1E (30)
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
*/
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| clk| wrlvl | cpo |wrdata|2T
+ * ranks| mhz|adjst| start | |delay |
+ */
+ {4, 850, 4, 6, 0xff, 2, 0},
+ {4, 950, 5, 7, 0xff, 2, 0},
+ {4, 1050, 5, 8, 0xff, 2, 0},
+ {4, 1250, 5, 10, 0xff, 2, 0},
+ {4, 1350, 5, 11, 0xff, 2, 0},
+ {4, 1666, 5, 12, 0xff, 2, 0},
+ {2, 850, 5, 6, 0xff, 2, 0},
+ {2, 1050, 5, 7, 0xff, 2, 0},
+ {2, 1250, 4, 6, 0xff, 2, 0},
+ {2, 1350, 5, 7, 0xff, 2, 0},
+ {2, 1666, 5, 8, 0xff, 2, 0},
+ {1, 1250, 4, 6, 0xff, 2, 0},
+ {1, 1335, 4, 7, 0xff, 2, 0},
+ {1, 1666, 4, 8, 0xff, 2, 0},
+ {}
+};
+/*
+ * The two slots have slightly different timing. The center values are good
+ * for both slots. We use identical speed tables for them. In future use, if
+ * DIMMs have fewer center values that require two separated tables, copy the
+ * udimm0 table to udimm1 and make changes to clk_adjust and wrlvl_start.
+ */
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+ udimm0,
+};
-/* XXX: these values need to be checked for all interleaving modes. */
-/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
- * seem reliable, but errors will appear when memory intensive
- * program is run. */
-/* XXX: Single rank at 800 MHz is OK. */
-const board_specific_parameters_t board_specific_parameters[][20] = {
- {
- /* memory controller 0 */
- /* lo| hi| num| clk| cpo|wrdata|2T */
- /* mhz| mhz|ranks|adjst| | delay| */
- { 0, 333, 2, 6, 7, 3, 0},
- {334, 400, 2, 6, 9, 3, 0},
- {401, 549, 2, 6, 11, 3, 0},
- {550, 680, 2, 1, 10, 5, 0},
- {681, 850, 2, 1, 12, 5, 0},
- {851, 1050, 2, 1, 12, 5, 0},
- {1051, 1250, 2, 1, 15, 4, 0},
- {1251, 1350, 2, 1, 15, 4, 0},
- { 0, 333, 1, 6, 7, 3, 0},
- {334, 400, 1, 6, 9, 3, 0},
- {401, 549, 1, 6, 11, 3, 0},
- {550, 680, 1, 1, 10, 5, 0},
- {681, 850, 1, 1, 12, 5, 0}
- },
-
- {
- /* memory controller 1 */
- /* lo| hi| num| clk| cpo|wrdata|2T */
- /* mhz| mhz|ranks|adjst| | delay| */
- { 0, 333, 2, 6, 7, 3, 0},
- {334, 400, 2, 6, 9, 3, 0},
- {401, 549, 2, 6, 11, 3, 0},
- {550, 680, 2, 1, 11, 6, 0},
- {681, 850, 2, 1, 13, 6, 0},
- {851, 1050, 2, 1, 13, 6, 0},
- {1051, 1250, 2, 1, 15, 4, 0},
- {1251, 1350, 2, 1, 15, 4, 0},
- { 0, 333, 1, 6, 7, 3, 0},
- {334, 400, 1, 6, 9, 3, 0},
- {401, 549, 1, 6, 11, 3, 0},
- {550, 680, 1, 1, 11, 6, 0},
- {681, 850, 1, 1, 13, 6, 0}
- }
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| clk| wrlvl | cpo |wrdata|2T
+ * ranks| mhz|adjst| start | |delay |
+ */
+ {4, 850, 4, 6, 0xff, 2, 0},
+ {4, 950, 5, 7, 0xff, 2, 0},
+ {4, 1050, 5, 8, 0xff, 2, 0},
+ {4, 1250, 5, 10, 0xff, 2, 0},
+ {4, 1350, 5, 11, 0xff, 2, 0},
+ {4, 1666, 5, 12, 0xff, 2, 0},
+ {2, 850, 4, 6, 0xff, 2, 0},
+ {2, 1050, 4, 7, 0xff, 2, 0},
+ {2, 1666, 4, 8, 0xff, 2, 0},
+ {1, 850, 4, 5, 0xff, 2, 0},
+ {1, 950, 4, 7, 0xff, 2, 0},
+ {1, 1666, 4, 8, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The two slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+ rdimm0,
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
- const board_specific_parameters_t *pbsp =
- &(board_specific_parameters[ctrl_num][0]);
- u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
- sizeof(board_specific_parameters[0][0]);
- u32 i;
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
- /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
- * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
- * there are two dimms in the controller, set odt_rd_cfg to 3 and
- * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
- */
- for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
- if (i&1) { /* odd CS */
- popts->cs_local_opts[i].odt_rd_cfg = 0;
- popts->cs_local_opts[i].odt_wr_cfg = 1;
- } else { /* even CS */
- if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
- popts->cs_local_opts[i].odt_rd_cfg = 0;
- popts->cs_local_opts[i].odt_wr_cfg = 1;
- } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
- popts->cs_local_opts[i].odt_rd_cfg = 3;
- popts->cs_local_opts[i].odt_wr_cfg = 3;
- }
- }
+ if (ctrl_num > 1) {
+ printf("Wrong parameter for controller number %d", ctrl_num);
+ return;
}
+ if (!pdimm->n_ranks)
+ return;
+
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[ctrl_num];
+ else
+ pbsp = udimms[ctrl_num];
+
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
- for (i = 0; i < num_params; i++) {
- if (ddr_freq >= pbsp->datarate_mhz_low &&
- ddr_freq <= pbsp->datarate_mhz_high &&
- pdimm->n_ranks == pbsp->n_ranks) {
- popts->cpo_override = 0xff; /* force auto CPO calibration */
- popts->write_data_delay = 2;
- popts->clk_adjust = 5; /* Force value to be 5/8 clock cycle */
- popts->twoT_en = pbsp->force_2T;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->twoT_en = pbsp->force_2T;
+ goto found;
+ }
+ pbsp_highest = pbsp;
}
pbsp++;
}
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found "
+ "for data rate %lu MT/s!\n"
+ "Trying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->twoT_en = pbsp_highest->force_2T;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
* Write leveling override
*/
popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xa;
- popts->wrlvl_start = 0x7;
+ popts->wrlvl_sample = 0xf;
+
/*
* Rtt and Rtt_WR override
*/
- popts->rtt_override = 1;
- popts->rtt_override_value = DDR3_RTT_120_OHM;
- popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
+ popts->rtt_override = 0;
/* Enable ZQ calibration */
popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 60 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....");
+
+ if (fsl_use_spd()) {
+ puts("using SPD\n");
+ dram_size = fsl_ddr_sdram();
+ } else {
+ puts("using fixed parameters\n");
+ dram_size = fixed_sdram();
+ }
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ debug(" DDR: ");
+ return dram_size;
}
projects / platform / kernel / u-boot.git / blobdiff