u8 byte;
int i;
const int ir_i2c_addr[] = {0x38, 0x08, 0x09};
-#ifdef CONFIG_DM_I2C
+#if CONFIG_IS_ENABLED(DM_I2C)
struct udevice *dev;
#endif
/* Check all the address */
for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) {
i2caddress = ir_i2c_addr[i];
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
ret = i2c_read(i2caddress,
IR36021_MFR_ID_OFFSET, 1, (void *)&byte,
sizeof(byte));
int i, ret, voltage_read = 0;
u16 vol_mon;
u8 buf[2];
-#ifdef CONFIG_DM_I2C
+#if CONFIG_IS_ENABLED(DM_I2C)
struct udevice *dev;
#endif
for (i = 0; i < NUM_READINGS; i++) {
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
ret = i2c_read(I2C_VOL_MONITOR_ADDR,
I2C_VOL_MONITOR_BUS_V_OFFSET, 1,
(void *)&buf, 2);
int i, ret, voltage_read = 0;
u16 vol_mon;
u8 buf;
-#ifdef CONFIG_DM_I2C
+#if CONFIG_IS_ENABLED(DM_I2C)
struct udevice *dev;
#endif
for (i = 0; i < NUM_READINGS; i++) {
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
ret = i2c_read(i2caddress,
IR36021_LOOP1_VOUT_OFFSET,
1, (void *)&buf, 1);
int ret, vcode = 0;
u8 chan = PWM_CHANNEL0;
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
/* select the PAGE 0 using PMBus commands PAGE for VDD*/
ret = i2c_write(I2C_VOL_MONITOR_ADDR,
PMBUS_CMD_PAGE, 1, &chan, 1);
return ret;
}
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
/*read the output voltage using PMBus command READ_VOUT*/
ret = i2c_read(I2C_VOL_MONITOR_ADDR,
PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2);
vid = DIV_ROUND_UP(vdd - 245, 5);
#endif
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET,
1, (void *)&vid, sizeof(vid));
#else
vdd & 0xFF, (vdd & 0xFF00) >> 8};
/* Write the desired voltage code to the regulator */
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
/* Check write protect state */
ret = i2c_read(I2C_VOL_MONITOR_ADDR,
PMBUS_CMD_WRITE_PROTECT, 1,
}
/* check IR chip work on Intel mode*/
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
ret = i2c_read(i2caddress,
IR36021_INTEL_MODE_OOFSET,
1, (void *)&buf, 1);
}
/* check IR chip work on Intel mode*/
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
ret = i2c_read(i2caddress,
IR36021_INTEL_MODE_OOFSET,
1, (void *)&buf, 1);