#include <common.h>
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#ifdef CONFIG_NEW_NAND_CODE
+#if defined(CONFIG_CMD_NAND)
+#if !defined(CONFIG_NAND_LEGACY)
#include <nand.h>
#include <asm/arch/pxa-regs.h>
+#ifdef CFG_DFC_DEBUG1
+# define DFC_DEBUG1(fmt, args...) printf(fmt, ##args)
+#else
+# define DFC_DEBUG1(fmt, args...)
+#endif
+
+#ifdef CFG_DFC_DEBUG2
+# define DFC_DEBUG2(fmt, args...) printf(fmt, ##args)
+#else
+# define DFC_DEBUG2(fmt, args...)
+#endif
+
+#ifdef CFG_DFC_DEBUG3
+# define DFC_DEBUG3(fmt, args...) printf(fmt, ##args)
+#else
+# define DFC_DEBUG3(fmt, args...)
+#endif
+
+#define MIN(x, y) ((x < y) ? x : y)
+
+/* These really don't belong here, as they are specific to the NAND Model */
+static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
+
+static struct nand_bbt_descr delta_bbt_descr = {
+ .options = 0,
+ .offs = 0,
+ .len = 2,
+ .pattern = scan_ff_pattern
+};
+
+static struct nand_ecclayout delta_oob = {
+ .eccbytes = 6,
+ .eccpos = {2, 3, 4, 5, 6, 7},
+ .oobfree = { {8, 2}, {12, 4} }
+};
+
/*
- * hardware specific access to control-lines
- * function borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c)
+ * not required for Monahans DFC
*/
-static void delta_hwcontrol(struct mtd_info *mtdinfo, int cmd)
+static void dfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
-#if 0
- struct nand_chip *this = mtdinfo->priv;
- ulong base = (ulong) this->IO_ADDR_W;
-
- switch(cmd) {
- case NAND_CTL_SETCLE:
- MACRO_NAND_CTL_SETCLE((unsigned long)base);
- break;
- case NAND_CTL_CLRCLE:
- MACRO_NAND_CTL_CLRCLE((unsigned long)base);
- break;
- case NAND_CTL_SETALE:
- MACRO_NAND_CTL_SETALE((unsigned long)base);
- break;
- case NAND_CTL_CLRALE:
- MACRO_NAND_CTL_CLRALE((unsigned long)base);
- break;
- case NAND_CTL_SETNCE:
- MACRO_NAND_ENABLE_CE((unsigned long)base);
- break;
- case NAND_CTL_CLRNCE:
- MACRO_NAND_DISABLE_CE((unsigned long)base);
- break;
- }
-#endif
+ return;
}
-
+#if 0
/* read device ready pin */
-static int delta_device_ready(struct mtd_info *mtdinfo)
+static int dfc_device_ready(struct mtd_info *mtdinfo)
{
if(NDSR & NDSR_RDY)
return 1;
else
return 0;
-#if 0
- struct nand_chip *this = mtdinfo->priv;
- ulong rb_gpio_pin;
-
- /* use the base addr to find out which chip are we dealing with */
- switch((ulong) this->IO_ADDR_W) {
- case CFG_NAND0_BASE:
- rb_gpio_pin = CFG_NAND0_RDY;
- break;
- case CFG_NAND1_BASE:
- rb_gpio_pin = CFG_NAND1_RDY;
- break;
- default: /* this should never happen */
- return 0;
- break;
+ return 0;
+}
+#endif
+
+/*
+ * Write buf to the DFC Controller Data Buffer
+ */
+static void dfc_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
+{
+ unsigned long bytes_multi = len & 0xfffffffc;
+ unsigned long rest = len & 0x3;
+ unsigned long *long_buf;
+ int i;
+
+ DFC_DEBUG2("dfc_write_buf: writing %d bytes starting with 0x%x.\n", len, *((unsigned long*) buf));
+ if(bytes_multi) {
+ for(i=0; i<bytes_multi; i+=4) {
+ long_buf = (unsigned long*) &buf[i];
+ NDDB = *long_buf;
+ }
+ }
+ if(rest) {
+ printf("dfc_write_buf: ERROR, writing non 4-byte aligned data.\n");
}
+ return;
+}
- if (in32(GPIO0_IR) & rb_gpio_pin)
- return 1;
-#endif
+
+static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len)
+{
+ int i=0, j;
+
+ /* we have to be carefull not to overflow the buffer if len is
+ * not a multiple of 4 */
+ unsigned long bytes_multi = len & 0xfffffffc;
+ unsigned long rest = len & 0x3;
+ unsigned long *long_buf;
+
+ DFC_DEBUG3("dfc_read_buf: reading %d bytes.\n", len);
+ /* if there are any, first copy multiple of 4 bytes */
+ if(bytes_multi) {
+ for(i=0; i<bytes_multi; i+=4) {
+ long_buf = (unsigned long*) &buf[i];
+ *long_buf = NDDB;
+ }
+ }
+
+ /* ...then the rest */
+ if(rest) {
+ unsigned long rest_data = NDDB;
+ for(j=0;j<rest; j++)
+ buf[i+j] = (u_char) ((rest_data>>j) & 0xff);
+ }
+
+ return;
+}
+
+/*
+ * read a word. Not implemented as not used in NAND code.
+ */
+static u16 dfc_read_word(struct mtd_info *mtd)
+{
+ printf("dfc_read_word: UNIMPLEMENTED.\n");
return 0;
}
-static u_char delta_read_byte(struct mtd_info *mtd)
+/* global var, too bad: mk@tbd: move to ->priv pointer */
+static unsigned long read_buf = 0;
+static int bytes_read = -1;
+
+/*
+ * read a byte from NDDB Because we can only read 4 bytes from NDDB at
+ * a time, we buffer the remaining bytes. The buffer is reset when a
+ * new command is sent to the chip.
+ *
+ * WARNING:
+ * This function is currently only used to read status and id
+ * bytes. For these commands always 8 bytes need to be read from
+ * NDDB. So we read and discard these bytes right now. In case this
+ * function is used for anything else in the future, we must check
+ * what was the last command issued and read the appropriate amount of
+ * bytes respectively.
+ */
+static u_char dfc_read_byte(struct mtd_info *mtd)
{
-/* struct nand_chip *this = mtd->priv; */
- unsigned long tmp;
+ unsigned char byte;
+ unsigned long dummy;
- /* wait for read request */
- while(1) {
- if(NDSR & NDSR_RDDREQ) {
- NDSR |= NDSR_RDDREQ;
- break;
- }
+ if(bytes_read < 0) {
+ read_buf = NDDB;
+ dummy = NDDB;
+ bytes_read = 0;
}
+ byte = (unsigned char) (read_buf>>(8 * bytes_read++));
+ if(bytes_read >= 4)
+ bytes_read = -1;
- tmp = NDDB;
- printk("delta_read_byte: 0x%x.\n", tmp);
- return (u_char) tmp;
+ DFC_DEBUG2("dfc_read_byte: byte %u: 0x%x of (0x%x).\n", bytes_read - 1, byte, read_buf);
+ return byte;
}
-/* this is really monahans, not board specific ... */
-static void delta_cmdfunc(struct mtd_info *mtd, unsigned command,
- int column, int page_addr)
+/* calculate delta between OSCR values start and now */
+static unsigned long get_delta(unsigned long start)
{
- /* register struct nand_chip *this = mtd->priv; */
- unsigned long ndcb0=0, ndcb1=0, ndcb2=0;
- uchar command2;
+ unsigned long cur = OSCR;
+
+ if(cur < start) /* OSCR overflowed */
+ return (cur + (start^0xffffffff));
+ else
+ return (cur - start);
+}
- /* Clear NDSR */
- NDSR = 0xFFF;
-
- /* apparently NDCR[NDRUN] needs to be set before writing to NDCBx */
- NDCR |= NDCR_ND_RUN;
+/* delay function, this doesn't belong here */
+static void wait_us(unsigned long us)
+{
+ unsigned long start = OSCR;
+ us *= OSCR_CLK_FREQ;
+
+ while (get_delta(start) < us) {
+ /* do nothing */
+ }
+}
+
+static void dfc_clear_nddb(void)
+{
+ NDCR &= ~NDCR_ND_RUN;
+ wait_us(CFG_NAND_OTHER_TO);
+}
+
+/* wait_event with timeout */
+static unsigned long dfc_wait_event(unsigned long event)
+{
+ unsigned long ndsr, timeout, start = OSCR;
+
+ if(!event)
+ return 0xff000000;
+ else if(event & (NDSR_CS0_CMDD | NDSR_CS0_BBD))
+ timeout = CFG_NAND_PROG_ERASE_TO * OSCR_CLK_FREQ;
+ else
+ timeout = CFG_NAND_OTHER_TO * OSCR_CLK_FREQ;
- /* wait for write command request
- * hmm, might be nice if this could time-out. mk@tbd
- */
while(1) {
- if(NDSR & NDSR_WRCMDREQ) {
- NDSR |= NDSR_WRCMDREQ; /* Ack */
+ ndsr = NDSR;
+ if(ndsr & event) {
+ NDSR |= event;
break;
}
+ if(get_delta(start) > timeout) {
+ DFC_DEBUG1("dfc_wait_event: TIMEOUT waiting for event: 0x%lx.\n", event);
+ return 0xff000000;
+ }
+
+ }
+ return ndsr;
+}
+
+/* we don't always wan't to do this */
+static void dfc_new_cmd(void)
+{
+ int retry = 0;
+ unsigned long status;
+
+ while(retry++ <= CFG_NAND_SENDCMD_RETRY) {
+ /* Clear NDSR */
+ NDSR = 0xFFF;
+
+ /* set NDCR[NDRUN] */
+ if(!(NDCR & NDCR_ND_RUN))
+ NDCR |= NDCR_ND_RUN;
+
+ status = dfc_wait_event(NDSR_WRCMDREQ);
+
+ if(status & NDSR_WRCMDREQ)
+ return;
+
+ DFC_DEBUG2("dfc_new_cmd: FAILED to get WRITECMDREQ, retry: %d.\n", retry);
+ dfc_clear_nddb();
}
+ DFC_DEBUG1("dfc_new_cmd: giving up after %d retries.\n", retry);
+}
- /* if command is a double byte cmd, we set bit double cmd bit 19 */
- command2 = (command>>8) & 0xFF;
- ndcb0 = command | ((command2 ? 1 : 0) << 19);
+/* this function is called after Programm and Erase Operations to
+ * check for success or failure */
+static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this)
+{
+ unsigned long ndsr=0, event=0;
+ int state = this->state;
+
+ if(state == FL_WRITING) {
+ event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
+ } else if(state == FL_ERASING) {
+ event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
+ }
+
+ ndsr = dfc_wait_event(event);
+
+ if((ndsr & NDSR_CS0_BBD) || (ndsr & 0xff000000))
+ return(0x1); /* Status Read error */
+ return 0;
+}
+
+/* cmdfunc send commands to the DFC */
+static void dfc_cmdfunc(struct mtd_info *mtd, unsigned command,
+ int column, int page_addr)
+{
+ /* register struct nand_chip *this = mtd->priv; */
+ unsigned long ndcb0=0, ndcb1=0, ndcb2=0, event=0;
+
+ /* clear the ugly byte read buffer */
+ bytes_read = -1;
+ read_buf = 0;
switch (command) {
+ case NAND_CMD_READ0:
+ DFC_DEBUG3("dfc_cmdfunc: NAND_CMD_READ0, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
+ dfc_new_cmd();
+ ndcb0 = (NAND_CMD_READ0 | (4<<16));
+ column >>= 1; /* adjust for 16 bit bus */
+ ndcb1 = (((column>>1) & 0xff) |
+ ((page_addr<<8) & 0xff00) |
+ ((page_addr<<8) & 0xff0000) |
+ ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
+ event = NDSR_RDDREQ;
+ goto write_cmd;
+ case NAND_CMD_READ1:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READ1 unimplemented!\n");
+ goto end;
+ case NAND_CMD_READOOB:
+ DFC_DEBUG1("dfc_cmdfunc: NAND_CMD_READOOB unimplemented!\n");
+ goto end;
case NAND_CMD_READID:
- printk("delta_cmdfunc: NAND_CMD_READID.\n");
- ndcb0 |= ((3 << 21) | (1 << 16)); /* addr cycles*/
- break;
+ dfc_new_cmd();
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READID.\n");
+ ndcb0 = (NAND_CMD_READID | (3 << 21) | (1 << 16)); /* addr cycles*/
+ event = NDSR_RDDREQ;
+ goto write_cmd;
case NAND_CMD_PAGEPROG:
+ /* sent as a multicommand in NAND_CMD_SEQIN */
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_PAGEPROG empty due to multicmd.\n");
+ goto end;
case NAND_CMD_ERASE1:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE1, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
+ dfc_new_cmd();
+ ndcb0 = (0xd060 | (1<<25) | (2<<21) | (1<<19) | (3<<16));
+ ndcb1 = (page_addr & 0x00ffffff);
+ goto write_cmd;
case NAND_CMD_ERASE2:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE2 empty due to multicmd.\n");
+ goto end;
case NAND_CMD_SEQIN:
+ /* send PAGE_PROG command(0x1080) */
+ dfc_new_cmd();
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
+ ndcb0 = (0x1080 | (1<<25) | (1<<21) | (1<<19) | (4<<16));
+ column >>= 1; /* adjust for 16 bit bus */
+ ndcb1 = (((column>>1) & 0xff) |
+ ((page_addr<<8) & 0xff00) |
+ ((page_addr<<8) & 0xff0000) |
+ ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
+ event = NDSR_WRDREQ;
+ goto write_cmd;
case NAND_CMD_STATUS:
- return;
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_STATUS.\n");
+ dfc_new_cmd();
+ ndcb0 = NAND_CMD_STATUS | (4<<21);
+ event = NDSR_RDDREQ;
+ goto write_cmd;
case NAND_CMD_RESET:
- return;
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_RESET.\n");
+ ndcb0 = NAND_CMD_RESET | (5<<21);
+ event = NDSR_CS0_CMDD;
+ goto write_cmd;
default:
- printk("delta_cmdfunc: error, unkown command issued.\n");
- return;
+ printk("dfc_cmdfunc: error, unsupported command.\n");
+ goto end;
}
+ write_cmd:
NDCB0 = ndcb0;
- NDCB1 = ndcb1;
- NDCB2 = ndcb2;
+ NDCB0 = ndcb1;
+ NDCB0 = ndcb2;
+
+ /* wait_event: */
+ dfc_wait_event(event);
+ end:
+ return;
}
-void delta_dfc_gpio_init()
+static void dfc_gpio_init(void)
{
- printf("Setting up DFC GPIO's.\n");
+ DFC_DEBUG2("Setting up DFC GPIO's.\n");
/* no idea what is done here, see zylonite.c */
GPIO4 = 0x1;
-
+
DF_ALE_WE1 = 0x00000001;
DF_ALE_WE2 = 0x00000001;
DF_nCS0 = 0x00000001;
* - dev_ready: hardwarespecific function for accesing device ready/busy line
* - enable_hwecc?: function to enable (reset) hardware ecc generator. Must
* only be provided if a hardware ECC is available
- * - eccmode: mode of ecc, see defines
+ * - ecc.mode: mode of ecc, see defines
* - chip_delay: chip dependent delay for transfering data from array to
* read regs (tR)
* - options: various chip options. They can partly be set to inform
* Members with a "?" were not set in the merged testing-NAND branch,
* so they are not set here either.
*/
-void board_nand_init(struct nand_chip *nand)
+int board_nand_init(struct nand_chip *nand)
{
unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR;
/* set up GPIO Control Registers */
- delta_dfc_gpio_init();
+ dfc_gpio_init();
/* turn on the NAND Controller Clock (104 MHz @ D0) */
CKENA |= (CKENA_4_NAND | CKENA_9_SMC);
-
- /* NAND Timing Parameters (in ns) */
-#define NAND_TIMING_tCH 10
-#define NAND_TIMING_tCS 0
-#define NAND_TIMING_tWH 20
-#define NAND_TIMING_tWP 40
-#define NAND_TIMING_tRH 20
-#define NAND_TIMING_tRP 40
-#define NAND_TIMING_tR 11123
-#define NAND_TIMING_tWHR 110
-#define NAND_TIMING_tAR 10
-
-/* Maximum values for NAND Interface Timing Registers in DFC clock
- * periods */
-#define DFC_MAX_tCH 7
-#define DFC_MAX_tCS 7
-#define DFC_MAX_tWH 7
-#define DFC_MAX_tWP 7
-#define DFC_MAX_tRH 7
-#define DFC_MAX_tRP 15
-#define DFC_MAX_tR 65535
-#define DFC_MAX_tWHR 15
-#define DFC_MAX_tAR 15
-
-#define DFC_CLOCK 104 /* DFC Clock is 104 MHz */
-#define DFC_CLK_PER_US DFC_CLOCK/1000 /* clock period in ns */
-#define MIN(x, y) ((x < y) ? x : y)
-
- tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US) + 1),
+#undef CFG_TIMING_TIGHT
+#ifndef CFG_TIMING_TIGHT
+ tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US) + 1),
DFC_MAX_tCH);
- tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US) + 1),
+ tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US) + 1),
DFC_MAX_tCS);
tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US) + 1),
DFC_MAX_tWH);
DFC_MAX_tWHR);
tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) + 1),
DFC_MAX_tAR);
-
+#else /* this is the tight timing */
+
+ tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US)),
+ DFC_MAX_tCH);
+ tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US)),
+ DFC_MAX_tCS);
+ tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US)),
+ DFC_MAX_tWH);
+ tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US)),
+ DFC_MAX_tWP);
+ tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US)),
+ DFC_MAX_tRH);
+ tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US)),
+ DFC_MAX_tRP);
+ tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) - tCH - 2),
+ DFC_MAX_tR);
+ tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) - tCH - 2),
+ DFC_MAX_tWHR);
+ tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) - 2),
+ DFC_MAX_tAR);
+#endif /* CFG_TIMING_TIGHT */
+
+
+ DFC_DEBUG2("tCH=%u, tCS=%u, tWH=%u, tWP=%u, tRH=%u, tRP=%u, tR=%u, tWHR=%u, tAR=%u.\n", tCH, tCS, tWH, tWP, tRH, tRP, tR, tWHR, tAR);
/* tRP value is split in the register */
if(tRP & (1 << 4)) {
(tRP_high << 6) |
(tRH << 3) |
(tRP << 0);
-
+
NDTR1CS0 = (tR << 16) |
(tWHR << 4) |
(tAR << 0);
-
-
/* If it doesn't work (unlikely) think about:
* - ecc enable
* - chip select don't care
* - cs don't care, see if we can enable later!
* - row address start position (after second cycle)
* - pages per block = 32
+ * - ND_RDY : clears command buffer
*/
- NDCR = (NDCR_ND_ARB_EN | /* enable bus arbiter */
- NDCR_SPARE_EN | /* use the spare area */
+ /* NDCR_NCSX | /\* Chip select busy don't care *\/ */
+
+ NDCR = (NDCR_SPARE_EN | /* use the spare area */
NDCR_DWIDTH_C | /* 16bit DFC data bus width */
NDCR_DWIDTH_M | /* 16 bit Flash device data bus width */
(2 << 16) | /* read id count = 7 ???? mk@tbd */
- NDCE_RDYM | /* flash device ready ir masked */
- NDCE_CS0_PAGEDM | /* ND_nCSx page done ir masked */
- NDCE_CS1_PAGEDM |
- NDCE_CS0_CMDDM | /* ND_CSx command done ir masked */
- NDCE_CS1_CMDDM |
- NDCE_CS0_BBDM | /* ND_CSx bad block detect ir masked */
- NDCE_CS1_BBDM |
- NDCE_DBERRM | /* double bit error ir masked */
- NDCE_SBERRM | /* single bit error ir masked */
- NDCE_WRDREQM | /* write data request ir masked */
- NDCE_RDDREQM | /* read data request ir masked */
- NDCE_WRCMDREQM); /* write command request ir masked */
-
-
-
- nand->hwcontrol = delta_hwcontrol;
- nand->dev_ready = delta_device_ready;
- nand->eccmode = NAND_ECC_SOFT;
- nand->chip_delay = NAND_DELAY_US;
+ NDCR_ND_ARB_EN | /* enable bus arbiter */
+ NDCR_RDYM | /* flash device ready ir masked */
+ NDCR_CS0_PAGEDM | /* ND_nCSx page done ir masked */
+ NDCR_CS1_PAGEDM |
+ NDCR_CS0_CMDDM | /* ND_CSx command done ir masked */
+ NDCR_CS1_CMDDM |
+ NDCR_CS0_BBDM | /* ND_CSx bad block detect ir masked */
+ NDCR_CS1_BBDM |
+ NDCR_DBERRM | /* double bit error ir masked */
+ NDCR_SBERRM | /* single bit error ir masked */
+ NDCR_WRDREQM | /* write data request ir masked */
+ NDCR_RDDREQM | /* read data request ir masked */
+ NDCR_WRCMDREQM); /* write command request ir masked */
+
+
+ /* wait 10 us due to cmd buffer clear reset */
+ /* wait(10); */
+
+
+ nand->cmd_ctrl = dfc_hwcontrol;
+/* nand->dev_ready = dfc_device_ready; */
+ nand->ecc.mode = NAND_ECC_SOFT;
+ nand->ecc.layout = &delta_oob;
nand->options = NAND_BUSWIDTH_16;
- nand->read_byte = delta_read_byte;
- nand->cmdfunc = delta_cmdfunc;
- /* nand->options = NAND_SAMSUNG_LP_OPTIONS; */
+ nand->waitfunc = dfc_wait;
+ nand->read_byte = dfc_read_byte;
+ nand->read_word = dfc_read_word;
+ nand->read_buf = dfc_read_buf;
+ nand->write_buf = dfc_write_buf;
+
+ nand->cmdfunc = dfc_cmdfunc;
+ nand->badblock_pattern = &delta_bbt_descr;
+ return 0;
}
#else
-#error "U-Boot legacy NAND support not available for delta board."
+ #error "U-Boot legacy NAND support not available for Monahans DFC."
#endif
#endif