0
};
-static u32 gpmc_nand_config[GPMC_MAX_REG] = {
- SMNAND_GPMC_CONFIG1,
- SMNAND_GPMC_CONFIG2,
- SMNAND_GPMC_CONFIG3,
- SMNAND_GPMC_CONFIG4,
- SMNAND_GPMC_CONFIG5,
- SMNAND_GPMC_CONFIG6,
- 0,
-};
-
#ifdef CONFIG_LCD
#ifdef CONFIG_CMD_NAND
static int splash_load_from_nand(u32 bmp_load_addr)
}
#endif /* CONFIG_CMD_NAND */
+#ifdef CONFIG_SPL_BUILD
+/*
+ * Routine: get_board_mem_timings
+ * Description: If we use SPL then there is no x-loader nor config header
+ * so we have to setup the DDR timings ourself on both banks.
+ */
+void get_board_mem_timings(struct board_sdrc_timings *timings)
+{
+ timings->mr = MICRON_V_MR_165;
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20); /* raswidth 14 needed */
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+}
+#endif
+
int splash_screen_prepare(void)
{
char *env_splashimage_value;
{
gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
- enable_gpmc_cs_config(gpmc_nand_config, &gpmc_cfg->cs[0],
- CONFIG_SYS_NAND_BASE, GPMC_SIZE_16M);
-
/* board id for Linux */
if (get_cpu_family() == CPU_OMAP34XX)
gd->bd->bi_arch_number = MACH_TYPE_CM_T35;
MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)); /*OFF_MODE*/
MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)); /*CLKOUT1*/
MUX_VAL(CP(SYS_CLKOUT2), (IDIS | PTU | DIS | M4)); /*green LED*/
- MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)); /*JTAG_nTRST*/
+ MUX_VAL(CP(JTAG_NTRST), (IEN | PTD | DIS | M0)); /*JTAG_NTRST*/
MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)); /*JTAG_TCK*/
MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)); /*JTAG_TMS*/
MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)); /*JTAG_TDI*/
cm_t3730_set_muxconf();
}
-#ifdef CONFIG_GENERIC_MMC
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+#define SB_T35_WP_GPIO 59
+
int board_mmc_getcd(struct mmc *mmc)
{
u8 val;
int board_mmc_init(bd_t *bis)
{
- return omap_mmc_init(0, 0, 0, -1, 59);
+ return omap_mmc_init(0, 0, 0, -1, SB_T35_WP_GPIO);
}
#endif