+// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (c) 2012 Michael Walle
* Michael Walle <michael@walle.cc>
*
* Based on sheevaplug/sheevaplug.c by
* Marvell Semiconductor <www.marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
*/
#include <common.h>
+#include <bootstage.h>
+#include <command.h>
+#include <env.h>
+#include <env_internal.h>
+#include <init.h>
#include <net.h>
#include <malloc.h>
#include <netdev.h>
#include <miiphy.h>
-#include <asm/arch/kirkwood.h>
+#include <spi.h>
+#include <spi_flash.h>
+#include <asm/arch/soc.h>
#include <asm/arch/cpu.h>
#include <asm/arch/mpp.h>
#include <asm/arch/gpio.h>
-#include <spi_flash.h>
+#include <asm/global_data.h>
+#include <linux/delay.h>
#include "lsxl.h"
* you can do this only with a working network connection. Therefore, a random
* ethernet address is generated if none is set and a DHCP request is sent.
* After a successful DHCP response is received, the network settings are
- * configured and the ncip parameter is set to the serverip. Eg. for a working
- * resuce mode, you should set 'next-server' to the host where the netconsole
- * client is started.
+ * configured and the ncip is unset. Therefore, all netconsole packets are
+ * broadcasted.
* Additionally, the bootsource is set to 'rescue'.
*/
* There are maximum 64 gpios controlled through 2 sets of registers
* the below configuration configures mainly initial LED status
*/
- kw_config_gpio(LSXL_OE_VAL_LOW,
- LSXL_OE_VAL_HIGH,
- LSXL_OE_LOW, LSXL_OE_HIGH);
+ mvebu_config_gpio(LSXL_OE_VAL_LOW,
+ LSXL_OE_VAL_HIGH,
+ LSXL_OE_LOW, LSXL_OE_HIGH);
/*
* Multi-Purpose Pins Functionality configuration
* These strappings are taken from the original vendor uboot port.
*/
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
int board_init(void)
{
/* address of boot parameters */
- gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
set_led(LED_POWER_BLINKING);
static void check_power_switch(void)
{
if (kw_gpio_get_value(GPIO_POWER_SWITCH)) {
- /* turn off HDD and USB power */
+ /* turn off fan, HDD and USB power */
kw_gpio_set_value(GPIO_HDD_POWER, 0);
kw_gpio_set_value(GPIO_USB_VBUS, 0);
+ kw_gpio_set_value(GPIO_FAN_HIGH, 1);
+ kw_gpio_set_value(GPIO_FAN_LOW, 1);
set_led(LED_OFF);
/* loop until released */
/* turn power on again */
kw_gpio_set_value(GPIO_HDD_POWER, 1);
kw_gpio_set_value(GPIO_USB_VBUS, 1);
+ kw_gpio_set_value(GPIO_FAN_HIGH, 0);
+ kw_gpio_set_value(GPIO_FAN_LOW, 0);
set_led(LED_POWER_BLINKING);
}
}
{
uchar enetaddr[6];
- if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
+ if (!eth_env_get_enetaddr("ethaddr", enetaddr)) {
/* signal unset/invalid ethaddr to user */
set_led(LED_INFO_BLINKING);
}
static void rescue_mode(void)
{
- uchar enetaddr[6];
-
printf("Entering rescue mode..\n");
-#ifdef CONFIG_RANDOM_MACADDR
- if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
- eth_random_enetaddr(enetaddr);
- if (eth_setenv_enetaddr("ethaddr", enetaddr)) {
- printf("Failed to set ethernet address\n");
- set_led(LED_ALARM_BLINKING);
- return;
- }
- }
-#endif
- setenv("bootsource", "rescue");
+ env_set("bootsource", "rescue");
}
static void check_push_button(void)
}
#endif
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
+#if CONFIG_IS_ENABLED(BOOTSTAGE)
void show_boot_progress(int progress)
{
if (progress > 0)