*/
#include <common.h>
+#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <netdev.h>
int dram_init(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+ gd->ram_size = imx_ddr_size();
return 0;
}
ARRAY_SIZE(feature_pads));
}
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+/* I2C2 - EEPROM */
+static struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
+ .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
+ .gp = IMX_GPIO_NR(2, 30)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
+ .gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
+ .gp = IMX_GPIO_NR(3, 16)
+ }
+};
+
+/* I2C3 - IO expander */
+static struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
+ .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
+ .gp = IMX_GPIO_NR(3, 17)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
+ .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
+ .gp = IMX_GPIO_NR(3, 18)
+ }
+};
+
+static void setup_iomux_i2c(void)
+{
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+}
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0x00C03F3F, &ccm->CCGR0);
+ writel(0x0030FC33, &ccm->CCGR1);
+ writel(0x0FFFC000, &ccm->CCGR2);
+ writel(0x3FF00000, &ccm->CCGR3);
+ writel(0x00FFF300, &ccm->CCGR4);
+ writel(0x0F0000C3, &ccm->CCGR5);
+ writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* enable AXI cache for VDOA/VPU/IPU */
+ writel(0xF00000CF, &iomux->gpr[4]);
+ /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+ writel(0x007F007F, &iomux->gpr[6]);
+ writel(0x007F007F, &iomux->gpr[7]);
+}
+
int board_early_init_f(void)
{
+ ccgr_init();
+ gpr_init();
+
setup_iomux_uart();
setup_iomux_spi();
+ setup_iomux_i2c();
setup_iomux_features();
return 0;
gpio_direction_input(IMX_GPIO_NR(4, 5));
ret = gpio_get_value(IMX_GPIO_NR(4, 5));
} else {
- gpio_direction_input(IMX_GPIO_NR(1, 4));
- ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
+ gpio_direction_input(IMX_GPIO_NR(1, 5));
+ ret = !gpio_get_value(IMX_GPIO_NR(1, 5));
}
return ret;
int board_mmc_init(bd_t *bis)
{
- s32 status = 0;
+ int ret;
u32 index = 0;
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
printf("Warning: you configured more USDHC controllers"
"(%d) then supported by the board (%d)\n",
index + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return status;
+ return -EINVAL;
}
- status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ if (ret)
+ return ret;
}
- return status;
+ return 0;
}
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-/* I2C3 - IO expander */
-static struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
- .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
- .gp = IMX_GPIO_NR(3, 17)
- },
- .sda = {
- .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-
-static iomux_v3_cfg_t const pwm_pad[] = {
- MX6_PAD_SD1_CMD__PWM4_OUT | MUX_PAD_CTRL(OUTPUT_40OHM),
-};
-
static void leds_on(void)
{
/* turn on all possible leds connected via GPIO expander */
bus = fec_get_miibus(base, -1);
if (!bus)
- return 0;
+ return -EINVAL;
/* scan phy 0 and 5 */
phydev = phy_find_by_mask(bus, 0x21, PHY_INTERFACE_MODE_RGMII);
if (!phydev) {
- free(bus);
- return 0;
+ ret = -EINVAL;
+ goto free_bus;
}
/* depending on the phy address we can detect our board version */
printf("using phy at %d\n", phydev->addr);
ret = fec_probe(bis, -1, base, bus, phydev);
- if (ret) {
- printf("FEC MXC: %s:failed\n", __func__);
- free(phydev);
- free(bus);
- }
+ if (ret)
+ goto free_phydev;
+
return 0;
+
+free_phydev:
+ free(phydev);
+free_bus:
+ free(bus);
+ return ret;
}
int board_init(void)
backlight_lcd_off();
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-
leds_on();
- /* enable ecspi3 clocks */
- enable_cspi_clock(1, 2);
-
-#ifdef CONFIG_CMD_SATA
+#ifdef CONFIG_SATA
setup_sata();
#endif