+// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <debug_uart.h>
+#include <init.h>
+#include <net.h>
+#include <vsprintf.h>
+#include <asm/global_data.h>
#include <linux/sizes.h>
#include <asm/arch/at91sam9263.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/hardware.h>
#include <lcd.h>
#include <atmel_lcdc.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
-#include <atmel_mci.h>
+#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
}
#endif
-#ifdef CONFIG_MACB
-static void at91sam9263ek_macb_hw_init(void)
-{
- at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC);
-
- /*
- * Disable pull-up on:
- * RXDV (PC25) => PHY normal mode (not Test mode)
- * ERX0 (PE25) => PHY ADDR0
- * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(1 << 25, &pio->pioc.pudr);
- writel((1 << 25) | (1 <<26), &pio->pioe.pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(1 << 25, &pio->pioc.puer);
- writel((1 << 25) | (1 <<26), &pio->pioe.puer);
-
- at91_macb_hw_init();
-}
-#endif
-
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 240,
#include <version.h>
#ifdef CONFIG_MTD_NOR_FLASH
-extern flash_info_t flash_info[];
+#include <flash.h>
#endif
void lcd_show_board_info(void)
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += nand_info[i]->size;
+ nand_size += get_nand_dev_by_index(i)->size;
#ifdef CONFIG_MTD_NOR_FLASH
flash_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
#endif /* CONFIG_LCD_INFO */
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI1);
+ at91_seriald_hw_init();
}
#endif
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOCDE);
-
- at91_seriald_hw_init();
return 0;
}
+#endif
int board_init(void)
{
#ifdef CONFIG_CMD_NAND
at91sam9263ek_nand_hw_init();
#endif
-#ifdef CONFIG_HAS_DATAFLASH
- at91_set_pio_output(AT91_PIO_PORTE, 20, 1); /* select spi0 clock */
- at91_spi0_hw_init(1 << 0);
-#endif
-#ifdef CONFIG_MACB
- at91sam9263ek_macb_hw_init();
-#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
{
}
#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00);
-#endif
- return rc;
-}