#include <common.h>
#include <asm/arch/at91cap9.h>
#include <asm/arch/at91cap9_matrix.h>
-#include <asm/arch/at91sam926x_mc.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
+#include <netdev.h>
#define MP_BLOCK_3_BASE 0xFDF00000
* Miscelaneous platform dependent initialisations
*/
-static void at91cap9_serial_hw_init(void)
+static void at91cap9_slowclock_hw_init(void)
{
-#ifdef CONFIG_USART0
- at91_set_A_periph(AT91_PIN_PA22, 1); /* TXD0 */
- at91_set_A_periph(AT91_PIN_PA23, 0); /* RXD0 */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US0);
-#endif
-
-#ifdef CONFIG_USART1
- at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */
- at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US1);
-#endif
-
-#ifdef CONFIG_USART2
- at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */
- at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US2);
-#endif
-
-#ifdef CONFIG_USART3 /* DBGU */
- at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */
- at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_SYS);
-#endif
+ /*
+ * On AT91CAP9 revC CPUs, the slow clock can be based on an
+ * internal impreciseRC oscillator or an external 32kHz oscillator.
+ * Switch to the latter.
+ */
+#define ARCH_ID_AT91CAP9_REVB 0x399
+#define ARCH_ID_AT91CAP9_REVC 0x601
+ if (at91_sys_read(AT91_PMC_VER) == ARCH_ID_AT91CAP9_REVC) {
+ unsigned i, tmp = at91_sys_read(AT91_SCKCR);
+ if ((tmp & AT91CAP9_SCKCR_OSCSEL) == AT91CAP9_SCKCR_OSCSEL_RC) {
+ extern void timer_init(void);
+ timer_init();
+ tmp |= AT91CAP9_SCKCR_OSC32EN;
+ at91_sys_write(AT91_SCKCR, tmp);
+ for (i = 0; i < 1200; i++)
+ udelay(1000);
+ tmp |= AT91CAP9_SCKCR_OSCSEL_32;
+ at91_sys_write(AT91_SCKCR, tmp);
+ udelay(200);
+ tmp &= ~AT91CAP9_SCKCR_RCEN;
+ at91_sys_write(AT91_SCKCR, tmp);
+ }
+ }
}
static void at91cap9_nor_hw_init(void)
at91_sys_write(AT91_SMC_MODE(3),
AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
AT91_SMC_EXNWMODE_DISABLE |
- AT91_SMC_DBW_8 | AT91_SMC_TDF_(1));
+#ifdef CONFIG_SYS_NAND_DBW_16
+ AT91_SMC_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+ AT91_SMC_DBW_8 |
+#endif
+ AT91_SMC_TDF_(1));
at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_PIOABCD);
}
#endif
-#ifdef CONFIG_HAS_DATAFLASH
-static void at91cap9_spi_hw_init(void)
-{
- at91_set_B_periph(AT91_PIN_PA5, 0); /* SPI0_NPCS0 */
-
- at91_set_B_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */
- at91_set_B_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */
- at91_set_B_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */
-
- /* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_SPI0);
-}
-#endif
-
#ifdef CONFIG_MACB
static void at91cap9_macb_hw_init(void)
{
/* Need to reset PHY -> 500ms reset */
at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- AT91_RSTC_ERSTL | (0x0D << 8) |
+ (AT91_RSTC_ERSTL & (0x0D << 8)) |
AT91_RSTC_URSTEN);
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
/* Wait for end hardware reset */
while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
+ /* Restore NRST value */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (AT91_RSTC_ERSTL & (0x0 << 8)) |
+ AT91_RSTC_URSTEN);
+
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PB22) |
pin_to_mask(AT91_PIN_PB25) |
pin_to_mask(AT91_PIN_PB26),
pin_to_controller(AT91_PIN_PA0) + PIO_PUER);
- at91_set_A_periph(AT91_PIN_PB21, 0); /* ETXCK_EREFCK */
- at91_set_A_periph(AT91_PIN_PB22, 0); /* ERXDV */
- at91_set_A_periph(AT91_PIN_PB25, 0); /* ERX0 */
- at91_set_A_periph(AT91_PIN_PB26, 0); /* ERX1 */
- at91_set_A_periph(AT91_PIN_PB27, 0); /* ERXER */
- at91_set_A_periph(AT91_PIN_PB28, 0); /* ETXEN */
- at91_set_A_periph(AT91_PIN_PB23, 0); /* ETX0 */
- at91_set_A_periph(AT91_PIN_PB24, 0); /* ETX1 */
- at91_set_A_periph(AT91_PIN_PB30, 0); /* EMDIO */
- at91_set_A_periph(AT91_PIN_PB29, 0); /* EMDC */
-
-#ifndef CONFIG_RMII
- at91_set_B_periph(AT91_PIN_PC25, 0); /* ECRS */
- at91_set_B_periph(AT91_PIN_PC26, 0); /* ECOL */
- at91_set_B_periph(AT91_PIN_PC22, 0); /* ERX2 */
- at91_set_B_periph(AT91_PIN_PC23, 0); /* ERX3 */
- at91_set_B_periph(AT91_PIN_PC27, 0); /* ERXCK */
- at91_set_B_periph(AT91_PIN_PC20, 0); /* ETX2 */
- at91_set_B_periph(AT91_PIN_PC21, 0); /* ETX3 */
- at91_set_B_periph(AT91_PIN_PC24, 0); /* ETXER */
-#endif
+ at91_macb_hw_init();
+
/* Unlock EMAC, 3 0 2 1 sequence */
#define MP_MAC_KEY0 0x5969cb2a
#define MP_MAC_KEY1 0xb4a1872e
}
#endif
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_clk: 4965000,
+ vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
+ ATMEL_LCDC_INVFRAME_INVERTED,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 5,
+ vl_left_margin: 1,
+ vl_right_margin:33,
+ vl_vsync_len: 1,
+ vl_upper_margin:1,
+ vl_lower_margin:0,
+ mmio: AT91CAP9_LCDC_BASE,
+};
+
+void lcd_enable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PC0, 0); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PC0, 1); /* power down */
+}
+
+static void at91cap9_lcd_hw_init(void)
+{
+ at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
+ at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
+ at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
+ at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
+ at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
+ at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
+ at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
+ at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
+ at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
+ at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
+ at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
+ at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
+ at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
+ at91_set_A_periph(AT91_PIN_PC17, 0); /* LCDD13 */
+ at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
+ at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
+ at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
+ at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
+ at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
+ at91_set_A_periph(AT91_PIN_PC25, 0); /* LCDD21 */
+ at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
+ at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
+
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_LCDC);
+
+ gd->fb_base = 0;
+}
+
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+
+void lcd_show_board_info(void)
+{
+ ulong dram_size, nand_size;
+ int i;
+ char temp[32];
+
+ lcd_printf ("%s\n", U_BOOT_VERSION);
+ lcd_printf ("(C) 2008 ATMEL Corp\n");
+ lcd_printf ("at91support@atmel.com\n");
+ lcd_printf ("%s CPU at %s MHz\n",
+ AT91_CPU_NAME,
+ strmhz(temp, AT91_CPU_CLOCK));
+
+ dram_size = 0;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ dram_size += gd->bd->bi_dram[i].size;
+ nand_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+ nand_size += nand_info[i].size;
+ lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
+ dram_size >> 20,
+ nand_size >> 20 );
+}
+#endif /* CONFIG_LCD_INFO */
+#endif
+
int board_init(void)
{
/* Enable Ctrlc */
/* adress of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- at91cap9_serial_hw_init();
+ at91_serial_hw_init();
+ at91cap9_slowclock_hw_init();
at91cap9_nor_hw_init();
#ifdef CONFIG_CMD_NAND
at91cap9_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
- at91cap9_spi_hw_init();
+ at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
at91cap9_macb_hw_init();
#ifdef CONFIG_USB_OHCI_NEW
at91cap9_uhp_hw_init();
#endif
-
+#ifdef CONFIG_LCD
+ at91cap9_lcd_hw_init();
+#endif
return 0;
}
#endif
}
#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)AT91CAP9_BASE_EMAC, 0x00);
+#endif
+ return rc;
+}
projects / platform / kernel / u-boot.git / blobdiff