extern void __ft_board_setup(void *blob, bd_t *bd);
ulong flash_get_size(ulong base, int banknum);
+static inline u32 get_async_pci_freq(void)
+{
+ if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) &
+ CONFIG_SYS_BCSR5_PCI66EN)
+ return 66666666;
+ else
+ return 33333333;
+}
+
int board_early_init_f(void)
{
u32 sdr0_cust0;
mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
mtdcr(UIC2SR, 0xffffffff); /* clear all */
+ /* Check and reconfigure the PCI sync clock if necessary */
+ ppc4xx_pci_sync_clock_config(get_async_pci_freq());
+
/* 50MHz tmrclk */
out_8((u8 *) CONFIG_SYS_BCSR_BASE + 0x04, 0x00);
{
char *s = getenv("serial#");
u8 rev;
- u8 val;
+ u32 clock = get_async_pci_freq();
#ifdef CONFIG_440EPX
printf("Board: Sequoia - AMCC PPC440EPx Evaluation Board");
#endif
rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0));
- val = in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) & CONFIG_SYS_BCSR5_PCI66EN;
- printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
+ printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000);
if (s != NULL) {
puts(", serial# ");
}
putc('\n');
+ /*
+ * Reconfiguration of the PCI sync clock is already done,
+ * now check again if everything is in range:
+ */
+ if (ppc4xx_pci_sync_clock_config(clock)) {
+ printf("ERROR: PCI clocking incorrect (async=%d "
+ "sync=%ld)!\n", clock, get_PCI_freq());
+ }
+
return (0);
}
}
#endif /* defined(CONFIG_PCI) */
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-/*
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- */
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Cactus is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
-
#if defined(CONFIG_POST)
/*
* Returns 1 if keys pressed to start the power-on long-running tests