/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
- mtdcr(uic0sr, 0xffffffff); /* clear all */
- mtdcr(uic0er, 0x00000000); /* disable all */
- mtdcr(uic0cr, 0x00000009); /* ATI & UIC1 crit are critical */
- mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */
- mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */
- mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic0sr, 0xffffffff); /* clear all */
-
- mtdcr(uic1sr, 0xffffffff); /* clear all */
- mtdcr(uic1er, 0x00000000); /* disable all */
- mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */
- mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */
- mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic1sr, 0xffffffff); /* clear all */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000009); /* ATI & UIC1 crit are critical */
+ mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
/*--------------------------------------------------------------------
* Setup the GPIO pins
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
#endif /* defined(CONFIG_PCI) */
/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
* pci_master_init
*
************************************************************************/
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-/*************************************************************************
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Bamboo is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
-
/*----------------------------------------------------------------------------+
| is_powerpc440ep_pass1.
+----------------------------------------------------------------------------*/
|
+-------------------------------------------------------------------------*/
/* NVRAM - FPGA */
- mtebc(pb5ap, EBC0_BNAP_NVRAM_FPGA);
- mtebc(pb5cr, EBC0_BNCR_NVRAM_FPGA_CS5);
+ mtebc(PB5AP, EBC0_BNAP_NVRAM_FPGA);
+ mtebc(PB5CR, EBC0_BNCR_NVRAM_FPGA_CS5);
/*-------------------------------------------------------------------------+
|
case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
/* Read Serial Device Strap Register1 in PPC440EP */
- mfsdr(sdr_sdstp1, sdr0_sdstp1);
+ mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
/* Default Strap Settings 5-7 */
/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
/* Read Serial Device Strap Register1 in PPC440EP */
- mfsdr(sdr_sdstp1, sdr0_sdstp1);
+ mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
/*-------------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, EBC0_CFG_EBTC_DRIVEN |
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, EBC0_CFG_EBTC_DRIVEN |
EBC0_CFG_PTD_ENABLED |
EBC0_CFG_RTC_2048PERCLK |
EBC0_CFG_EMPL_LOW |
| Initialize EBC Bank 0-4
+-------------------------------------------------------------------------*/
/* EBC Bank0 */
- mtebc(pb0ap, ebc0_cs0_bnap_value);
- mtebc(pb0cr, ebc0_cs0_bncr_value);
+ mtebc(PB0AP, ebc0_cs0_bnap_value);
+ mtebc(PB0CR, ebc0_cs0_bncr_value);
/* EBC Bank1 */
- mtebc(pb1ap, ebc0_cs1_bnap_value);
- mtebc(pb1cr, ebc0_cs1_bncr_value);
+ mtebc(PB1AP, ebc0_cs1_bnap_value);
+ mtebc(PB1CR, ebc0_cs1_bncr_value);
/* EBC Bank2 */
- mtebc(pb2ap, ebc0_cs2_bnap_value);
- mtebc(pb2cr, ebc0_cs2_bncr_value);
+ mtebc(PB2AP, ebc0_cs2_bnap_value);
+ mtebc(PB2CR, ebc0_cs2_bncr_value);
/* EBC Bank3 */
- mtebc(pb3ap, ebc0_cs3_bnap_value);
- mtebc(pb3cr, ebc0_cs3_bncr_value);
+ mtebc(PB3AP, ebc0_cs3_bnap_value);
+ mtebc(PB3CR, ebc0_cs3_bncr_value);
/* EBC Bank4 */
- mtebc(pb4ap, ebc0_cs4_bnap_value);
- mtebc(pb4cr, ebc0_cs4_bncr_value);
+ mtebc(PB4AP, ebc0_cs4_bnap_value);
+ mtebc(PB4CR, ebc0_cs4_bncr_value);
return;
}
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL;
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE;
- mfsdr(sdr_usb0, sdr0_usb0);
+ mfsdr(SDR0_USB0, sdr0_usb0);
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB20D_DEVSEL;
- mtsdr(sdr_usb0, sdr0_usb0);
+ mtsdr(SDR0_USB0, sdr0_usb0);
usb2_device_selection_in_fpga();
}
/* USB1.1 Device Selection */
if (ppc440ep_core_selection[USB1_DEVICE] == CORE_SELECTED)
{
- mfsdr(sdr_usb0, sdr0_usb0);
+ mfsdr(SDR0_USB0, sdr0_usb0);
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB11D_DEVSEL;
- mtsdr(sdr_usb0, sdr0_usb0);
+ mtsdr(SDR0_USB0, sdr0_usb0);
}
/* USB1.1 Host Selection */
if (ppc440ep_core_selection[USB1_HOST] == CORE_SELECTED)
{
- mfsdr(sdr_usb0, sdr0_usb0);
+ mfsdr(SDR0_USB0, sdr0_usb0);
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_LEEN_MASK;
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_LEEN_ENABLE;
- mtsdr(sdr_usb0, sdr0_usb0);
+ mtsdr(SDR0_USB0, sdr0_usb0);
}
/* NAND Flash Selection */
update_ndfc_ios(gpio_tab);
#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
- mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL |
+ mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
SDR0_CUST0_NDFC_ENABLE |
SDR0_CUST0_NDFC_BW_8_BIT |
SDR0_CUST0_NDFC_ARE_MASK |
SDR0_CUST0_CHIPSELGAT_EN1 |
SDR0_CUST0_CHIPSELGAT_EN2);
#else
- mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL |
+ mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
SDR0_CUST0_NDFC_ENABLE |
SDR0_CUST0_NDFC_BW_8_BIT |
SDR0_CUST0_NDFC_ARE_MASK |
else
{
/* Set Mux on EMAC */
- mtsdr(sdr_cust0, SDR0_CUST0_MUX_EMAC_SEL);
+ mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_EMAC_SEL);
}
/* MII Selection */
if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED)
{
update_zii_ios(gpio_tab);
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_MII);
}
if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED)
{
update_zii_ios(gpio_tab);
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_RMII);
}
if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED)
{
update_zii_ios(gpio_tab);
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_SMII);
}
/* Packet Reject Function Enable */
if (ppc440ep_core_selection[PACKET_REJ_FUNC_EN] == CORE_SELECTED)
{
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_PKT_REJ_MASK) | SDR0_MFR_PKT_REJ_EN;;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
}
/* Perform effective access to hardware */
- mtsdr(sdr_pfc1, sdr0_pfc1);
+ mtsdr(SDR0_PFC1, sdr0_pfc1);
set_chip_gpio_configuration(GPIO0, gpio_tab);
set_chip_gpio_configuration(GPIO1, gpio_tab);
projects / kernel / u-boot.git / blobdiff