+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2004, 2007-2012 Freescale Semiconductor, Inc.
* Copyright (C) 2003 Motorola,Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/* U-Boot Startup Code for Motorola 85xx PowerPC based Embedded Boards
#include <asm-offsets.h>
#include <config.h>
#include <mpc85xx.h>
-#include <version.h>
+#include <system-constants.h>
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#define LAW_EN 0x80000000
#if defined(CONFIG_NAND_SPL) || \
- (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL))
+ (defined(CONFIG_SPL_BUILD) && CONFIG_IS_ENABLED(INIT_MINIMAL))
#define MINIMAL_SPL
#endif
#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT) && \
- !defined(CONFIG_SECURE_BOOT) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+ !defined(CONFIG_NXP_ESBC) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define NOR_BOOT
#endif
GOT_ENTRY(_FIXUP_TABLE_)
#ifndef MINIMAL_SPL
- GOT_ENTRY(_start)
GOT_ENTRY(_start_of_vectors)
GOT_ENTRY(_end_of_vectors)
GOT_ENTRY(transfer_to_handler)
GOT_ENTRY(__bss_start)
END_GOT
+#ifdef CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+
+/* Maximal size of the image */
+#ifdef CONFIG_SPL_BUILD
+#define MAX_IMAGE_SIZE (CONFIG_SPL_MAX_SIZE - (CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA * 512))
+#else
+#define MAX_IMAGE_SIZE CONFIG_SYS_L2_SIZE
+#endif
+
+#if defined(CONFIG_SPL_BUILD) && CONFIG_SPL_MAX_SIZE < CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA * 512
+#error "CONFIG_SPL_MAX_SIZE is too small for CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA"
+#endif
+
+#if MAX_IMAGE_SIZE > CONFIG_SYS_L2_SIZE
+#error "Image is too big"
+#endif
+
+#define DIV_ROUND_UP(a, b) (((a) + (b) - 1) / (b))
+#define ALIGN(x, a) (DIV_ROUND_UP(x, a) * (a))
+
+/* Definitions from C header file asm/immap_85xx.h */
+
+#define CFG_SYS_MPC85xx_L2_OFFSET 0x20000
+
+#define MPC85xx_L2CTL 0x000
+#define MPC85xx_L2CTL_L2E 0x80000000
+#define MPC85xx_L2CTL_L2SRAM_ENTIRE 0x00010000
+
+#define MPC85xx_L2SRBAR0 0x100
+
+#define MPC85xx_L2ERRDIS 0xe44
+#define MPC85xx_L2ERRDIS_MBECC 0x00000008
+#define MPC85xx_L2ERRDIS_SBECC 0x00000004
+
+/* Definitions from C header file fsl_esdhc.h */
+
+#define ESDHCCTL 0x0002e40c
+#define ESDHCCTL_SNOOP 0x00000040
+
+/*
+ * QorIQ pre-PBL eSDHC boot sector:
+ * Instruct BootROM to configure L2 SRAM and eSDHC then load image
+ * from SD card into L2 SRAM and finally jump to image entry point.
+ */
+ .section .bootsect, "a"
+ .globl bootsect
+
+bootsect:
+ .org 0x40 /* BOOT signature */
+ .ascii "BOOT"
+
+ .org 0x48 /* Number of bytes to be copied, must be multiple of block size (512) */
+ .long ALIGN(MAX_IMAGE_SIZE, 512)
+
+ .org 0x50 /* Source address from the beginning of boot sector in byte address format, must be multiple of block size (512) */
+ .long (CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_START + CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA) * 512
+
+ .org 0x58 /* Target address in the system's local memory address space */
+ .long CONFIG_SYS_MONITOR_BASE
+
+ .org 0x60 /* Execution starting address */
+ .long _start
+
+ .org 0x68 /* Number of configuration data pairs */
+ .long DIV_ROUND_UP(.Lconf_pair_end - .Lconf_pair_start, 8)
+
+ .org 0x80 /* Start of configuration */
+ .Lconf_pair_start:
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + CFG_SYS_MPC85xx_L2_OFFSET + MPC85xx_L2SRBAR0 /* Address: L2 memory-mapped SRAM base addr 0 */
+ .long CONFIG_SYS_INIT_L2_ADDR
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + CFG_SYS_MPC85xx_L2_OFFSET + MPC85xx_L2ERRDIS /* Address: L2 cache error disable */
+ .long MPC85xx_L2ERRDIS_MBECC | MPC85xx_L2ERRDIS_SBECC
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + CFG_SYS_MPC85xx_L2_OFFSET + MPC85xx_L2CTL /* Address: L2 configuration 0 */
+ .long MPC85xx_L2CTL_L2E | MPC85xx_L2CTL_L2SRAM_ENTIRE
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + ESDHCCTL /* Address: eSDHC DMA control */
+ .long ESDHCCTL_SNOOP
+
+ .long 0x40000001 /* Command: Delay in 8 CCB clocks */
+ .long 256
+
+ .long 0x80000001 /* End of configuration */
+ .Lconf_pair_end:
+
+ .org 0x1b8 /* Reserved for MBR/DBR */
+ .org 0x200 /* End of boot sector */
+
+#endif
+#endif
+
/*
* e500 Startup -- after reset only the last 4KB of the effective
* address space is mapped in the MMU L2 TLB1 Entry0. The .bootpg
*/
.section .bootpg,"ax"
- .globl _start_e500
+ .globl _start
-_start_e500:
+_start:
/* Enable debug exception */
li r1,MSR_DE
- mtmsr r1
+ mtmsr r1
/*
* If we got an ePAPR device tree pointer passed in as r3, we need that
#endif
-#if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_E500MC) && \
+#if defined(CONFIG_NXP_ESBC) && defined(CONFIG_E500MC) && \
!defined(CONFIG_E6500)
/* ISBC uses L2 as stack.
* Disable L2 cache here so that u-boot can enable it later
/* Interrupt vectors do not fit in minimal SPL. */
#if !defined(MINIMAL_SPL)
/* Setup interrupt vectors */
- lis r1,CONFIG_SYS_MONITOR_BASE@h
+ lis r1,CONFIG_VAL(SYS_MONITOR_BASE)@h
mtspr IVPR,r1
li r4,CriticalInput@l
mtspr DBCR0,r0
#endif
-#ifdef CONFIG_ARCH_MPC8569
-#define CONFIG_SYS_LBC_ADDR (CONFIG_SYS_CCSRBAR_DEFAULT + 0x5000)
-#define CONFIG_SYS_LBCR_ADDR (CONFIG_SYS_LBC_ADDR + 0xd0)
-
- /* MPC8569 Rev.0 silcon needs to set bit 13 of LBCR to allow elBC to
- * use address space which is more than 12bits, and it must be done in
- * the 4K boot page. So we set this bit here.
- */
-
- /* create a temp mapping TLB0[0] for LBCR */
- create_tlb0_entry 0, \
- 0, BOOKE_PAGESZ_4K, \
- CONFIG_SYS_LBC_ADDR, MAS2_I|MAS2_G, \
- CONFIG_SYS_LBC_ADDR, MAS3_SW|MAS3_SR, \
- 0, r6
-
- /* Set LBCR register */
- lis r4,CONFIG_SYS_LBCR_ADDR@h
- ori r4,r4,CONFIG_SYS_LBCR_ADDR@l
-
- lis r5,CONFIG_SYS_LBC_LBCR@h
- ori r5,r5,CONFIG_SYS_LBC_LBCR@l
- stw r5,0(r4)
- isync
-
- /* invalidate this temp TLB */
- lis r4,CONFIG_SYS_LBC_ADDR@h
- ori r4,r4,CONFIG_SYS_LBC_ADDR@l
- tlbivax 0,r4
- isync
-
-#endif /* CONFIG_ARCH_MPC8569 */
-
/*
* Search for the TLB that covers the code we're executing, and shrink it
* so that it covers only this 4K page. That will ensure that any other
blt 1b
#if defined(CONFIG_SYS_PPC_E500_DEBUG_TLB) && !defined(MINIMAL_SPL) && \
- !defined(CONFIG_SECURE_BOOT)
+ !defined(CONFIG_NXP_ESBC)
/*
* TLB entry for debuggging in AS1
* Create temporary TLB entry in AS0 to handle debug exception
*/
create_tlb1_entry CONFIG_SYS_PPC_E500_DEBUG_TLB, \
0, BOOKE_PAGESZ_4M, \
- CONFIG_SYS_MONITOR_BASE & 0xffc00000, MAS2_I|MAS2_G, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xffc00000, MAS2_I|MAS2_G, \
0xffc00000, MAS3_SX|MAS3_SW|MAS3_SR, \
0, r6
*/
create_tlb1_entry CONFIG_SYS_PPC_E500_DEBUG_TLB, \
0, BOOKE_PAGESZ_256K, \
- CONFIG_SYS_MONITOR_BASE & 0xfffc0000, MAS2_I, \
- CONFIG_SYS_MONITOR_BASE & 0xfffc0000, MAS3_SX|MAS3_SW|MAS3_SR, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xfffc0000, MAS2_I, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xfffc0000, MAS3_SX|MAS3_SW|MAS3_SR, \
0, r6
#endif
#endif
/* create a temp mapping in AS=1 to the 4M boot window */
create_tlb1_entry 15, \
1, BOOKE_PAGESZ_4M, \
- CONFIG_SYS_MONITOR_BASE & 0xffc00000, MAS2_I|MAS2_G, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xffc00000, MAS2_I|MAS2_G, \
0xffc00000, MAS3_SX|MAS3_SW|MAS3_SR, \
0, r6
-#elif !defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT)
+#elif !defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_NXP_ESBC)
/* create a temp mapping in AS = 1 for Flash mapping
* created by PBL for ISBC code
*/
create_tlb1_entry 15, \
1, BOOKE_PAGESZ_1M, \
- CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS2_I|MAS2_G, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xfff00000, MAS2_I|MAS2_G, \
CONFIG_SYS_PBI_FLASH_WINDOW & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \
0, r6
* and for targets with CONFIG_SPL like T1, T2, T4, only for
* u-boot-spl i.e. CONFIG_SPL_BUILD
*/
-#elif defined(CONFIG_RAMBOOT_PBL) && defined(CONFIG_SECURE_BOOT) && \
+#elif defined(CONFIG_RAMBOOT_PBL) && defined(CONFIG_NXP_ESBC) && \
(!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
- /* create a temp mapping in AS = 1 for mapping CONFIG_SYS_MONITOR_BASE
+ /* create a temp mapping in AS = 1 for mapping CONFIG_VAL(SYS_MONITOR_BASE)
* to L3 Address configured by PBL for ISBC code
*/
create_tlb1_entry 15, \
1, BOOKE_PAGESZ_1M, \
- CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS2_I|MAS2_G, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xfff00000, MAS2_I|MAS2_G, \
CONFIG_SYS_INIT_L3_ADDR & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \
0, r6
#else
/*
- * create a temp mapping in AS=1 to the 1M CONFIG_SYS_MONITOR_BASE space, the main
- * image has been relocated to CONFIG_SYS_MONITOR_BASE on the second stage.
+ * create a temp mapping in AS=1 to the 1M CONFIG_VAL(SYS_MONITOR_BASE) space, the main
+ * image has been relocated to CONFIG_VAL(SYS_MONITOR_BASE) on the second stage.
*/
create_tlb1_entry 15, \
1, BOOKE_PAGESZ_1M, \
- CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS2_I|MAS2_G, \
- CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xfff00000, MAS2_I|MAS2_G, \
+ CONFIG_VAL(SYS_MONITOR_BASE) & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \
0, r6
#endif
#else
/* Calculate absolute address in FLASH and jump there */
/*--------------------------------------------------------------*/
- lis r3,CONFIG_SYS_MONITOR_BASE@h
- ori r3,r3,CONFIG_SYS_MONITOR_BASE@l
- addi r3,r3,_start_cont - _start
+ lis r3,_start_cont@h
+ ori r3,r3,_start_cont@l
mtlr r3
blr
#endif
.text
- .globl _start
-_start:
- .long 0x27051956 /* U-BOOT Magic Number */
- .globl version_string
-version_string:
- .ascii U_BOOT_VERSION_STRING, "\0"
-
- .align 4
.globl _start_cont
_start_cont:
/* Setup the stack in initial RAM,could be L2-as-SRAM or L1 dcache*/
lis r3,(CONFIG_SYS_INIT_RAM_ADDR)@h
ori r3,r3,((CONFIG_SYS_INIT_SP_OFFSET-16)&~0xf)@l /* Align to 16 */
-#ifdef CONFIG_SYS_MALLOC_F_LEN
-
-#if CONFIG_SYS_MALLOC_F_LEN + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE
-#error "CONFIG_SYS_MALLOC_F_LEN too large to fit into initial RAM."
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
+#if CONFIG_VAL(SYS_MALLOC_F_LEN) + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE
+#error "SYS_MALLOC_F_LEN too large to fit into initial RAM."
#endif
/* Leave 16+ byte for back chain termination and NULL return address */
- subi r3,r3,((CONFIG_SYS_MALLOC_F_LEN+16+15)&~0xf)
+ subi r3,r3,((CONFIG_VAL(SYS_MALLOC_F_LEN)+16+15)&~0xf)
#endif
/* End of RAM */
li r0,0
-1: subi r4,r4,4
- stw r0,0(r4)
- cmplw r4,r3
+1: subi r4,r4,4
+ stw r0,0(r4)
+ cmplw r4,r3
bne 1b
-#ifdef CONFIG_SYS_MALLOC_F_LEN
- lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h
- ori r4,r4,(CONFIG_SYS_GBL_DATA_OFFSET)@l
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
+ lis r4,SYS_INIT_SP_ADDR@h
+ ori r4,r4,SYS_INIT_SP_ADDR@l
addi r3,r3,16 /* Pre-relocation malloc area */
stw r3,GD_MALLOC_BASE(r4)
mr r1,r3 /* Transfer to SP(r1) */
GET_GOT
+ /* Needed for -msingle-pic-base */
+ bl _GLOBAL_OFFSET_TABLE_@local-4
+ mflr r30
/* Pass our potential ePAPR device tree pointer to cpu_init_early_f */
mr r3, r24
blr
/*
- * void relocate_code (addr_sp, gd, addr_moni)
+ * void relocate_code(addr_sp, gd, addr_moni)
*
* This "function" does not return, instead it continues in RAM
* after relocating the monitor code.
GET_GOT
#ifndef CONFIG_SPL_SKIP_RELOCATE
mr r3,r5 /* Destination Address */
- lis r4,CONFIG_SYS_MONITOR_BASE@h /* Source Address */
- ori r4,r4,CONFIG_SYS_MONITOR_BASE@l
+ lis r4,CONFIG_VAL(SYS_MONITOR_BASE)@h /* Source Address */
+ ori r4,r4,CONFIG_VAL(SYS_MONITOR_BASE)@l
lwz r5,GOT(__init_end)
sub r5,r5,r4
li r6,CONFIG_SYS_CACHELINE_SIZE /* Cache Line Size */
/*
* Fix GOT pointer:
*
- * New GOT-PTR = (old GOT-PTR - CONFIG_SYS_MONITOR_BASE) + Destination Address
+ * New GOT-PTR = (old GOT-PTR - CONFIG_VAL(SYS_MONITOR_BASE)) + Destination Address
*
* Offset:
*/
* initialization, now running from RAM.
*/
- addi r0,r10,in_ram - _start
+ addi r0,r10,in_ram - CONFIG_VAL(SYS_MONITOR_BASE)
/*
* As IVPR is going to point RAM address,