[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers

[platform/adaptation/renesas_rcar/renesas_kernel.git] / arch / powerpc / Kconfig.debug

diff --git a/arch/powerpc/Kconfig.debug b/arch/powerpc/Kconfig.debug
index f70e795..464f9b4 100644 (file)
--- a/arch/powerpc/Kconfig.debug
+++ b/arch/powerpc/Kconfig.debug
@@ -20,7 +20,7 @@ config DEBUG_STACK_USAGE
 
 config DEBUG_PAGEALLOC
         bool "Debug page memory allocations"
-        depends on DEBUG_KERNEL && !SOFTWARE_SUSPEND
+        depends on DEBUG_KERNEL && !HIBERNATION
         help
           Unmap pages from the kernel linear mapping after free_pages().
           This results in a large slowdown, but helps to find certain types
@@ -32,7 +32,7 @@ config HCALL_STATS
        depends on PPC_PSERIES && DEBUG_FS
        help
          Adds code to keep track of the number of hypervisor calls made and
-         the amount of time spent in hypervisor callsr.  Wall time spent in
+         the amount of time spent in hypervisor calls.  Wall time spent in
          each call is always calculated, and if available CPU cycles spent
          are also calculated.  A directory named hcall_inst is added at the
          root of the debugfs filesystem.  Within the hcall_inst directory
@@ -124,6 +124,16 @@ config IRQSTACKS
          for handling hard and soft interrupts.  This can help avoid
          overflowing the process kernel stacks.
 
+config VIRQ_DEBUG
+       bool "Expose hardware/virtual IRQ mapping via debugfs"
+       depends on DEBUG_FS && PPC_MERGE
+       help
+         This option will show the mapping relationship between hardware irq
+         numbers and virtual irq numbers. The mapping is exposed via debugfs
+         in the file powerpc/virq_mapping.
+
+         If you don't know what this means you don't need it.
+
 config BDI_SWITCH
        bool "Include BDI-2000 user context switcher"
        depends on DEBUG_KERNEL && PPC32
@@ -134,7 +144,7 @@ config BDI_SWITCH
 
 config BOOTX_TEXT
        bool "Support for early boot text console (BootX or OpenFirmware only)"
-       depends PPC_OF
+       depends PPC_OF && PPC_MULTIPLATFORM
        help
          Say Y here to see progress messages from the boot firmware in text
          mode. Requires either BootX or Open Firmware.
@@ -211,6 +221,15 @@ config PPC_EARLY_DEBUG_44x
          Select this to enable early debugging for IBM 44x chips via the
          inbuilt serial port.
 
+config PPC_EARLY_DEBUG_CPM
+       bool "Early serial debugging for Freescale CPM-based serial ports"
+       depends on SERIAL_CPM
+       select PIN_TLB if PPC_8xx
+       help
+         Select this to enable early debugging for Freescale chips
+         using a CPM-based serial port.  This assumes that the bootwrapper
+         has run, and set up the CPM in a particular way.
+
 endchoice
 
 config PPC_EARLY_DEBUG_44x_PHYSLOW
@@ -223,4 +242,16 @@ config PPC_EARLY_DEBUG_44x_PHYSHIGH
        depends PPC_EARLY_DEBUG_44x
        default "0x1"
 
+config PPC_EARLY_DEBUG_CPM_ADDR
+       hex "CPM UART early debug transmit descriptor address"
+       depends on PPC_EARLY_DEBUG_CPM
+       default "0xfa202008" if PPC_EP88XC
+       default "0xf0000008" if CPM2
+       default "0xff002008" if CPM1
+       help
+         This specifies the address of the transmit descriptor
+         used for early debug output.  Because it is needed before
+         platform probing is done, all platforms selected must
+         share the same address.
+
 endmenu