#define ERR_NCOR 0x8000 /* Error Not Corrected Indicator */
-/* ******************** TWO-WIRE INTERFACE (TWI) MASKS ***********************/
-/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y); ) */
-#define CLKLOW(x) ((x) & 0xFF) /* Periods Clock Is Held Low */
-#define CLKHI(y) (((y)&0xFF)<<0x8) /* Periods Before New Clock Low */
-
-/* TWI_PRESCALE Masks */
-#define PRESCALE 0x007F /* SCLKs Per Internal Time Reference (10MHz) */
-#define TWI_ENA 0x0080 /* TWI Enable */
-#define SCCB 0x0200 /* SCCB Compatibility Enable */
-
-/* TWI_SLAVE_CTL Masks */
-#define SEN 0x0001 /* Slave Enable */
-#define SADD_LEN 0x0002 /* Slave Address Length */
-#define STDVAL 0x0004 /* Slave Transmit Data Valid */
-#define NAK 0x0008 /* NAK/ACK* Generated At Conclusion Of Transfer */
-#define GEN 0x0010 /* General Call Adrress Matching Enabled */
-
-/* TWI_SLAVE_STAT Masks */
-#define SDIR 0x0001 /* Slave Transfer Direction (Transmit/Receive*) */
-#define GCALL 0x0002 /* General Call Indicator */
-
-/* TWI_MASTER_CTL Masks */
-#define MEN 0x0001 /* Master Mode Enable */
-#define MADD_LEN 0x0002 /* Master Address Length */
-#define MDIR 0x0004 /* Master Transmit Direction (RX/TX*) */
-#define FAST 0x0008 /* Use Fast Mode Timing Specs */
-#define STOP 0x0010 /* Issue Stop Condition */
-#define RSTART 0x0020 /* Repeat Start or Stop* At End Of Transfer */
-#define DCNT 0x3FC0 /* Data Bytes To Transfer */
-#define SDAOVR 0x4000 /* Serial Data Override */
-#define SCLOVR 0x8000 /* Serial Clock Override */
-
-/* TWI_MASTER_STAT Masks */
-#define MPROG 0x0001 /* Master Transfer In Progress */
-#define LOSTARB 0x0002 /* Lost Arbitration Indicator (Xfer Aborted) */
-#define ANAK 0x0004 /* Address Not Acknowledged */
-#define DNAK 0x0008 /* Data Not Acknowledged */
-#define BUFRDERR 0x0010 /* Buffer Read Error */
-#define BUFWRERR 0x0020 /* Buffer Write Error */
-#define SDASEN 0x0040 /* Serial Data Sense */
-#define SCLSEN 0x0080 /* Serial Clock Sense */
-#define BUSBUSY 0x0100 /* Bus Busy Indicator */
-
-/* TWI_INT_SRC and TWI_INT_ENABLE Masks */
-#define SINIT 0x0001 /* Slave Transfer Initiated */
-#define SCOMP 0x0002 /* Slave Transfer Complete */
-#define SERR 0x0004 /* Slave Transfer Error */
-#define SOVF 0x0008 /* Slave Overflow */
-#define MCOMP 0x0010 /* Master Transfer Complete */
-#define MERR 0x0020 /* Master Transfer Error */
-#define XMTSERV 0x0040 /* Transmit FIFO Service */
-#define RCVSERV 0x0080 /* Receive FIFO Service */
-
-/* TWI_FIFO_CTRL Masks */
-#define XMTFLUSH 0x0001 /* Transmit Buffer Flush */
-#define RCVFLUSH 0x0002 /* Receive Buffer Flush */
-#define XMTINTLEN 0x0004 /* Transmit Buffer Interrupt Length */
-#define RCVINTLEN 0x0008 /* Receive Buffer Interrupt Length */
-
-/* TWI_FIFO_STAT Masks */
-#define XMTSTAT 0x0003 /* Transmit FIFO Status */
-#define XMT_EMPTY 0x0000 /* Transmit FIFO Empty */
-#define XMT_HALF 0x0001 /* Transmit FIFO Has 1 Byte To Write */
-#define XMT_FULL 0x0003 /* Transmit FIFO Full (2 Bytes To Write) */
-
-#define RCVSTAT 0x000C /* Receive FIFO Status */
-#define RCV_EMPTY 0x0000 /* Receive FIFO Empty */
-#define RCV_HALF 0x0004 /* Receive FIFO Has 1 Byte To Read */
-#define RCV_FULL 0x000C /* Receive FIFO Full (2 Bytes To Read) */
-
-
/* ******************* PIN CONTROL REGISTER MASKS ************************/
/* PORT_MUX Masks */
#define PJSE 0x0001 /* Port J SPI/SPORT Enable */
projects / profile / ivi / kernel-adaptation-intel-automotive.git / blobdiff