* OTHER DEALINGS IN THE SOFTWARE.
*/
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+/* The Orange Pi Plus is an extended version of the Orange Pi 2 */
+#include "sun8i-h3-orangepi-2.dts"
/ {
- model = "Xunlong Orange Pi Plus";
+ model = "Xunlong Orange Pi Plus / Plus 2";
compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
aliases {
- serial0 = &uart0;
+ ethernet0 = &emac;
};
- chosen {
- stdout-path = "serial0:115200n8";
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&usb3_vbus_pin_a>;
regulator-name = "usb3-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
};
-&ehci1 {
- status = "okay";
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
};
&ehci3 {
status = "okay";
};
-&pio {
- usb3_vbus_pin_a: usb3_vbus_pin@0 {
- allwinner,pins = "PG11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
};
};
-&mmc0 {
+&mmc2 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
status = "okay";
};
-®_usb1_vbus {
- gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
- status = "okay";
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ drive-strength = <40>;
+ /* eMMC is missing pull-ups */
+ bias-pull-up;
};
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+&r_i2c {
status = "okay";
-};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG13";
+ reg_vdd_cpux: regulator@65 {
+ compatible = "silergy,sy8106a";
+ reg = <0x65>;
+ regulator-name = "vdd-cpux";
+ silergy,fixed-microvolt = <1200000>;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <200>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
};
&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
usb3_vbus-supply = <®_usb3_vbus>;
- status = "okay";
};