+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2016 Andreas Färber
* Copyright (c) 2016 BayLibre, Inc.
* Author: Kevin Hilman <khilman@kernel.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This library is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This library is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
aliases {
serial0 = &uart_AO;
+ ethernet0 = ðmac;
};
chosen {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
+
+ usb_otg_pwr: regulator-usb-pwrs {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB_OTG_PWR";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ /*
+ * signal name from schematics: PWREN
+ */
+ gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ blue {
+ label = "c2:blue:alive";
+ gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+
+ p5v0: regulator-p5v0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "P5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ hdmi_p5v0: regulator-hdmi_p5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "HDMI_P5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /* AP2331SA-7 */
+ vin-supply = <&p5v0>;
+ };
+
+ tflash_vdd: regulator-tflash_vdd {
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ /*
+ * signal name from schematics: TFLASH_VDD_EN
+ */
+ gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ /* U16 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ /*
+ * signal name from schematics: TF_3V3N_1V8_EN
+ */
+ gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+ /* U12/U13 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
+ };
+
+ vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ /* U18 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
+ };
+
+ vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vddio_ao1v8: regulator-vddio-ao1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ /* U17 RT9179GB */
+ vin-supply = <&p5v0>;
+ };
+
+ vddio_ao3v3: regulator-vddio-ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ /* U11 MP2161GJ-C499 */
+ vin-supply = <&p5v0>;
+ };
+
+ ddr3_1v5: regulator-ddr3_1v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "DDR3_1V5";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ /* U15 MP2161GJ-C499 */
+ vin-supply = <&p5v0>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ status = "okay";
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rgmii_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rgmii";
+
+ amlogic,tx-delay-ns = <2>;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ eth_phy0: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_15 */
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&gpio_ao {
+ /*
+ * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&hdmi_p5v0>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&i2c_A {
+ status = "okay";
+ pinctrl-0 = <&i2c_a_pins>;
+ pinctrl-names = "default";
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+ linux,rc-map-name = "rc-odroid";
+};
+
+&gpio_ao {
+ gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
+ "USB HUB nRESET", "USB OTG Power En",
+ "J7 Header Pin2", "IR In", "J7 Header Pin4",
+ "J7 Header Pin6", "J7 Header Pin5", "J7 Header Pin7",
+ "HDMI CEC", "SYS LED",
+ /* GPIO_TEST_N */
+ "";
+};
+
+&gpio {
+ gpio-line-names = /* Bank GPIOZ */
+ "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+ "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+ "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+ "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+ "Eth PHY nRESET", "Eth PHY Intc",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL", "",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+ "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+ "eMMC Reset", "eMMC CMD",
+ "", "", "", "", "", "", "",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "PWM D", "PWM B",
+ /* Bank GPIOY */
+ "Revision Bit0", "Revision Bit1", "",
+ "J2 Header Pin35", "", "", "", "J2 Header Pin36",
+ "J2 Header Pin31", "", "", "", "TF VDD En",
+ "J2 Header Pin32", "J2 Header Pin26", "", "",
+ /* Bank GPIOX */
+ "J2 Header Pin29", "J2 Header Pin24",
+ "J2 Header Pin23", "J2 Header Pin22",
+ "J2 Header Pin21", "J2 Header Pin18",
+ "J2 Header Pin33", "J2 Header Pin19",
+ "J2 Header Pin16", "J2 Header Pin15",
+ "J2 Header Pin12", "J2 Header Pin13",
+ "J2 Header Pin8", "J2 Header Pin10",
+ "", "", "", "", "",
+ "J2 Header Pin11", "", "J2 Header Pin7", "",
+ /* Bank GPIOCLK */
+ "", "", "", "";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vcc1v8>;
+};
+
+&scpi_clocks {
+ status = "disabled";
+};
+
+/* SD */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-ddr50;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc3v3>;
+ vqmmc-supply = <&vcc1v8>;
};
&uart_AO {
status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "disabled";
+ phy-supply = <&usb_otg_pwr>;
+};
+
+&usb1_phy {
+ status = "okay";
+ phy-supply = <&usb_otg_pwr>;
+};
+
+&usb0 {
+ status = "disabled";
+};
+
+&usb1 {
+ status = "okay";
};
projects / platform / kernel / u-boot.git / blobdiff