#include <common.h>
#include <i2c.h>
-#include <netdev.h>
-#include <miiphy.h>
#include <serial.h>
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
sunxi_gpio_set_cfgpin(SUNXI_GPH(20), SUN6I_GPH_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(21), SUN6I_GPH_UART0);
sunxi_gpio_set_pull(SUNXI_GPH(21), SUNXI_GPIO_PULL_UP);
+#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
+ sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
+ sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
+ sunxi_gpio_set_pull(SUNXI_GPH(13), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I)
sunxi_gpio_set_cfgpin(SUNXI_GPG(3), SUN5I_GPG_UART1);
sunxi_gpio_set_cfgpin(SUNXI_GPG(4), SUN5I_GPG_UART1);
sunxi_gpio_set_pull(SUNXI_GPG(4), SUNXI_GPIO_PULL_UP);
+#elif CONFIG_CONS_INDEX == 3 && defined(CONFIG_MACH_SUN8I)
+ sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_GPB_UART2);
+ sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_GPB_UART2);
+ sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPL(2), SUN8I_GPL_R_UART);
sunxi_gpio_set_cfgpin(SUNXI_GPL(3), SUN8I_GPL_R_UART);
void s_init(void)
{
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
+#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_A23
/* Magic (undocmented) value taken from boot0, without this DRAM
* access gets messed up (seems cache related) */
setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
#endif
-#if !defined CONFIG_SPL_BUILD && (defined CONFIG_MACH_SUN7I || \
- defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I)
+#if defined CONFIG_MACH_SUN6I || \
+ defined CONFIG_MACH_SUN7I || \
+ defined CONFIG_MACH_SUN8I
/* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
asm volatile(
"mrc p15, 0, r0, c1, c0, 1\n"
#ifdef CONFIG_SPL_BUILD
/* The sunxi internal brom will try to loader external bootloader
* from mmc0, nand flash, mmc2.
- * Unfortunately we can't check how SPL was loaded so assume
- * it's always the first SD/MMC controller
+ *
+ * Unfortunately we can't check how SPL was loaded so assume it's
+ * always the first SD/MMC controller, unless it was explicitly
+ * stated that SPL is on nand flash.
*/
u32 spl_boot_device(void)
{
-#ifdef CONFIG_SPL_FEL
+#if defined(CONFIG_SPL_NAND_SUPPORT)
/*
- * This is the legacy compile time configuration for a special FEL
- * enabled build. It has many restrictions and can only boot over USB.
+ * This is compile time configuration informing SPL, that it
+ * was loaded from nand flash.
*/
- return BOOT_DEVICE_BOARD;
+ return BOOT_DEVICE_NAND;
#else
/*
* When booting from the SD card, the "eGON.BT0" signature is expected
void reset_cpu(ulong addr)
{
-#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I)
+#ifdef CONFIG_SUNXI_GEN_SUN4I
static const struct sunxi_wdog *wdog =
&((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
/* sun5i sometimes gets stuck without this */
writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
}
-#else /* CONFIG_MACH_SUN6I || CONFIG_MACH_SUN8I || .. */
+#endif
+#ifdef CONFIG_SUNXI_GEN_SUN6I
static const struct sunxi_wdog *wdog =
((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
__maybe_unused int rc;
#ifdef CONFIG_MACPWR
+ gpio_request(CONFIG_MACPWR, "macpwr");
gpio_direction_output(CONFIG_MACPWR, 1);
mdelay(200);
#endif
-#ifdef CONFIG_SUNXI_EMAC
- rc = sunxi_emac_initialize(bis);
- if (rc < 0) {
- printf("sunxi: failed to initialize emac\n");
- return rc;
- }
-#endif
-
#ifdef CONFIG_SUNXI_GMAC
rc = sunxi_gmac_initialize(bis);
if (rc < 0) {