stdout-path = "serial0:115200n8";
};
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_keys>;
-
- wakeup {
- label = "Wake-Up";
- gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WAKEUP>;
- debounce-interval = <10>;
- wakeup-source;
- };
- };
-
reg_pcie_switch: regulator-pcie-switch {
compatible = "regulator-fixed";
- regulator-name = "pcie_switch";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
+ enable-active-high;
gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "pcie_switch";
startup-delay-us = <100000>;
- enable-active-high;
status = "okay";
};
reg_3v3_sw: regulator-3v3-sw {
compatible = "regulator-fixed";
- regulator-name = "3.3V_SW";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_SW";
};
};
status = "okay";
};
-&hdmi {
- status = "okay";
-};
-
/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
&i2c1 {
status = "okay";
- /*
- * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
- * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
- */
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- reg = <0x4a>;
- interrupt-parent = <&gpio6>;
- interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
- reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
- status = "disabled";
- };
-
pcie-switch@58 {
compatible = "plx,pex8605";
reg = <0x58>;
status = "okay";
};
-&ldb {
- status = "okay";
-};
-
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reset_moci>;
status = "okay";
};
-®_usb_otg_vbus {
+®_usb_host_vbus {
status = "okay";
};
-®_usb_host_vbus {
+®_usb_otg_vbus {
status = "okay";
};
/* MMC1 */
&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
- cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
status = "okay";
};
/* SD1 */
&usdhc2 {
+ cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
- cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
status = "okay";
};
-
-&iomuxc {
- /*
- * Mux the Apalis GPIOs
- */
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
- &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
- &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
- &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
- >;
-};