select PHYS_64BIT
select SYS_CACHE_SHIFT_6
-if ARM64
config POSITION_INDEPENDENT
bool "Generate position-independent pre-relocation code"
+ depends on ARM64 || CPU_V7A
help
U-Boot expects to be linked to a specific hard-coded address, and to
be loaded to and run from that address. This option lifts that
config INIT_SP_RELATIVE
bool "Specify the early stack pointer relative to the .bss section"
+ depends on ARM64
default n if ARCH_QEMU
default y if POSITION_INDEPENDENT
help
config SYS_INIT_SP_BSS_OFFSET
int "Early stack offset from the .bss base address"
+ depends on ARM64
depends on INIT_SP_RELATIVE
default 524288
help
do not overlap any appended DTB.
config LINUX_KERNEL_IMAGE_HEADER
+ depends on ARM64
bool
help
Place a Linux kernel image header at the start of the U-Boot binary.
image header reports the amount of memory (BSS and similar) that
U-Boot needs to use, but which isn't part of the binary.
-if LINUX_KERNEL_IMAGE_HEADER
config LNX_KRNL_IMG_TEXT_OFFSET_BASE
+ depends on LINUX_KERNEL_IMAGE_HEADER
hex
help
The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the
TEXT_OFFSET value written to the Linux kernel image header.
-endif
-endif
+
+config GICV2
+ bool
+
+config GICV3
+ bool
config GIC_V3_ITS
bool "ARM GICV3 ITS"
select REGMAP
select SYSCON
+ select IRQ
help
ARM GICV3 Interrupt translation service (ITS).
Basic support for programming locality specific peripheral
config HAS_THUMB2
bool
+config GPIO_EXTRA_HEADER
+ bool
+
# Used for compatibility with asm files copied from the kernel
config ARM_ASM_UNIFIED
bool
config SYS_ICACHE_OFF
bool "Do not enable icache"
- default n
help
Do not enable instruction cache in U-Boot.
config SYS_DCACHE_OFF
bool "Do not enable dcache"
- default n
help
Do not enable data cache in U-Boot.
default 4 if CPU_SA1100
default 8 if ARM64
-config SYS_CACHE_SHIFT_5
- bool
-
-config SYS_CACHE_SHIFT_6
- bool
-
-config SYS_CACHE_SHIFT_7
- bool
-
-config SYS_CACHELINE_SIZE
- int
- default 128 if SYS_CACHE_SHIFT_7
- default 64 if SYS_CACHE_SHIFT_6
- default 32 if SYS_CACHE_SHIFT_5
-
choice
prompt "Select the ARM data write cache policy"
default SYS_ARM_CACHE_WRITETHROUGH if TARGET_BCMCYGNUS || \
- TARGET_BCMNSP || CPU_PXA || RZA1
+ CPU_PXA || RZA1
default SYS_ARM_CACHE_WRITEBACK
config SYS_ARM_CACHE_WRITEBACK
config ARM_CORTEX_CPU_IS_UP
bool
- default n
config USE_ARCH_MEMCPY
bool "Use an assembly optimized implementation of memcpy"
config ARCH_AT91
bool "Atmel AT91"
+ select GPIO_EXTRA_HEADER
select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB
select SPL_SEPARATE_BSS if SPL
-config TARGET_EDB93XX
- bool "Support edb93xx"
- select CPU_ARM920T
- select PL010_SERIAL
-
config TARGET_ASPENITE
bool "Support aspenite"
select CPU_ARM926EJS
-
-config TARGET_GPLUGD
- bool "Support gplugd"
- select CPU_ARM926EJS
+ select GPIO_EXTRA_HEADER
config ARCH_DAVINCI
bool "TI DaVinci"
select CPU_ARM926EJS
+ select GPIO_EXTRA_HEADER
select SPL_DM_SPI if SPL
imply CMD_SAVES
help
select ARCH_MISC_INIT
select BOARD_EARLY_INIT_F
select CPU_ARM926EJS
+ select GPIO_EXTRA_HEADER
config ARCH_MVEBU
bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
select DM_SERIAL
select DM_SPI
select DM_SPI_FLASH
+ select GPIO_EXTRA_HEADER
select SPL_DM_SPI if SPL
select SPL_DM_SPI_FLASH if SPL
select OF_CONTROL
config ARCH_ORION5X
bool "Marvell Orion"
select CPU_ARM926EJS
-
-config TARGET_SPEAR300
- bool "Support spear300"
- select BOARD_EARLY_INIT_F
- select CPU_ARM926EJS
- select PL011_SERIAL
- imply CMD_SAVES
-
-config TARGET_SPEAR310
- bool "Support spear310"
- select BOARD_EARLY_INIT_F
- select CPU_ARM926EJS
- select PL011_SERIAL
- imply CMD_SAVES
-
-config TARGET_SPEAR320
- bool "Support spear320"
- select BOARD_EARLY_INIT_F
- select CPU_ARM926EJS
- select PL011_SERIAL
- imply CMD_SAVES
-
-config TARGET_SPEAR600
- bool "Support spear600"
- select BOARD_EARLY_INIT_F
- select CPU_ARM926EJS
- select PL011_SERIAL
- imply CMD_SAVES
+ select GPIO_EXTRA_HEADER
config TARGET_STV0991
bool "Support stv0991"
select DM_SERIAL
select DM_SPI
select DM_SPI_FLASH
+ select GPIO_EXTRA_HEADER
select PL01X_SERIAL
select SPI
select SPI_FLASH
imply CMD_DM
-config TARGET_X600
- bool "Support x600"
- select BOARD_LATE_INIT
- select CPU_ARM926EJS
- select PL011_SERIAL
- select SUPPORT_SPL
-
config TARGET_FLEA3
bool "Support flea3"
select CPU_ARM1136
+ select GPIO_EXTRA_HEADER
config ARCH_BCM283X
bool "Broadcom BCM283X family"
select DM
select DM_GPIO
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select PL01X_SERIAL
select SERIAL_SEARCH_ALL
select OF_CONTROL
imply CMD_DM
-config TARGET_VEXPRESS_CA15_TC2
- bool "Support vexpress_ca15_tc2"
- select CPU_V7A
- select CPU_V7_HAS_NONSEC
- select CPU_V7_HAS_VIRT
- select PL011_SERIAL
-
config ARCH_BCMSTB
bool "Broadcom BCM7XXX family"
select CPU_V7A
select DM
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select OF_PRIOR_STAGE
imply CMD_DM
This enables support for Broadcom ARM-based set-top box
chipsets, including the 7445 family of chips.
-config TARGET_VEXPRESS_CA5X2
- bool "Support vexpress_ca5x2"
- select CPU_V7A
- select PL011_SERIAL
-
-config TARGET_VEXPRESS_CA9X4
- bool "Support vexpress_ca9x4"
- select CPU_V7A
- select PL011_SERIAL
-
-config TARGET_BCM23550_W1D
- bool "Support bcm23550_w1d"
- select CPU_V7A
- imply CRC32_VERIFY
- imply FAT_WRITE
-
-config TARGET_BCM28155_AP
- bool "Support bcm28155_ap"
- select CPU_V7A
- imply CRC32_VERIFY
- imply FAT_WRITE
-
config TARGET_BCMCYGNUS
bool "Support bcmcygnus"
select CPU_V7A
+ select GPIO_EXTRA_HEADER
imply BCM_SF2_ETH
imply BCM_SF2_ETH_GMAC
imply CMD_HASH
imply HASH_VERIFY
imply NETDEVICES
-config TARGET_BCMNSP
- bool "Support bcmnsp"
- select CPU_V7A
-
config TARGET_BCMNS2
bool "Support Broadcom Northstar2"
select ARM64
+ select GPIO_EXTRA_HEADER
help
Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit
ARMv8 Cortex-A57 processors targeting a broad range of networking
select DM
select DM_GPIO
select DM_I2C
+ select DM_ETH
select DM_KEYBOARD
select DM_SERIAL
select DM_SPI
select DM_SPI_FLASH
select SPI
+ select GPIO_EXTRA_HEADER
imply SYS_THUMB_BUILD
imply CMD_DM
imply FAT_WRITE
select DM_GPIO
select DM_I2C
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
imply CMD_DM
config ARCH_HIGHBANK
bool "Calxeda Highbank"
select CPU_V7A
- select PL011_SERIAL
+ select PL01X_SERIAL
+ select DM
+ select DM_SERIAL
+ select OF_CONTROL
+ select OF_BOARD
+ select CLK
+ select CLK_CCF
+ select AHCI
+ select DM_ETH
+ select PHYS_64BIT
config ARCH_INTEGRATOR
bool "ARM Ltd. Integrator family"
select DM
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select PL01X_SERIAL
imply CMD_DM
select DM_GPIO
select DM_SERIAL
select DM_RESET
+ select GPIO_EXTRA_HEADER
select MSM_SMEM
select PINCTRL
select CLK
bool "TI Keystone"
select CMD_POWEROFF
select CPU_V7A
+ select DDR_SPD
+ select GPIO_EXTRA_HEADER
select SUPPORT_SPL
select SYS_ARCH_TIMER
select SYS_THUMB_BUILD
config ARCH_OMAP2PLUS
bool "TI OMAP2+"
select CPU_V7A
+ select GPIO_EXTRA_HEADER
select SPL_BOARD_INIT if SPL
select SPL_STACK_R if SPL
select SUPPORT_SPL
config ARCH_MESON
bool "Amlogic Meson"
+ select GPIO_EXTRA_HEADER
imply DISTRO_DEFAULTS
imply DM_RNG
help
config ARCH_MEDIATEK
bool "MediaTek SoCs"
select DM
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select SPL_DM if SPL
select SPL_LIBCOMMON_SUPPORT if SPL
select DM
select DM_GPIO
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select SPL_DM if SPL
select SUPPORT_SPL
imply CMD_DM
bool "NXP i.MX8 platform"
select ARM64
select DM
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select OF_CONTROL
select ENABLE_ARM_SOC_BOOT0_HOOK
config ARCH_IMX8M
bool "NXP i.MX8M platform"
select ARM64
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select SYS_FSL_HAS_SEC if IMX_HAB
select SYS_FSL_SEC_COMPAT_4
select SYS_FSL_SEC_LE
+ select SYS_I2C_MXC
select DM
select SUPPORT_SPL
imply CMD_DM
+config ARCH_IMX8ULP
+ bool "NXP i.MX8ULP platform"
+ select ARM64
+ select DM
+ select MACH_IMX
+ select OF_CONTROL
+ select SUPPORT_SPL
+ select GPIO_EXTRA_HEADER
+ imply CMD_DM
+
config ARCH_IMXRT
bool "NXP i.MXRT platform"
select CPU_V7M
select DM
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select SUPPORT_SPL
imply CMD_DM
config ARCH_MX23
bool "NXP i.MX23 family"
select CPU_ARM926EJS
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select PL011_SERIAL
select SUPPORT_SPL
config ARCH_MX25
bool "NXP MX25"
select CPU_ARM926EJS
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
imply MXC_GPIO
config ARCH_MX28
bool "NXP i.MX28 family"
select CPU_ARM926EJS
+ select GPIO_EXTRA_HEADER
select PL011_SERIAL
+ select MACH_IMX
select SUPPORT_SPL
config ARCH_MX31
bool "NXP i.MX31 family"
select CPU_ARM1136
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
config ARCH_MX7ULP
bool "NXP MX7ULP"
select CPU_V7A
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select SYS_FSL_HAS_SEC if IMX_HAB
select SYS_FSL_SEC_COMPAT_4
select SYS_FSL_SEC_LE
bool "Freescale MX7"
select ARCH_MISC_INIT
select CPU_V7A
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select SYS_FSL_HAS_SEC if IMX_HAB
select SYS_FSL_SEC_COMPAT_4
select SYS_FSL_SEC_LE
config ARCH_MX6
bool "Freescale MX6"
select CPU_V7A
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select SYS_FSL_HAS_SEC
select SYS_FSL_SEC_COMPAT_4
select SYS_FSL_SEC_LE
bool "Freescale MX5"
select BOARD_EARLY_INIT_F
select CPU_V7A
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
imply MXC_GPIO
config ARCH_NEXELL
bool "Nexell S5P4418/S5P6818 SoC"
select ENABLE_ARM_SOC_BOOT0_HOOK
select DM
+ select GPIO_EXTRA_HEADER
config ARCH_OWL
bool "Actions Semi OWL SoCs"
select DM
select DM_ETH
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select OWL_SERIAL
select CLK
select CLK_OWL
bool "Renesas ARM SoCs"
select DM
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
imply BOARD_EARLY_INIT_F
imply CMD_DM
imply FAT_WRITE
imply SYS_THUMB_BUILD
imply ARCH_MISC_INIT if DISPLAY_CPUINFO
-config TARGET_S32V234EVB
- bool "Support s32v234evb"
- select ARM64
- select SYS_FSL_ERRATUM_ESDHC111
-
config ARCH_SNAPDRAGON
bool "Qualcomm Snapdragon SoCs"
select ARM64
select DM
select DM_GPIO
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select MSM_SMEM
select OF_CONTROL
select OF_SEPARATE
select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
select DM
select DM_SERIAL
+ select GICV2
+ select GPIO_EXTRA_HEADER
select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
select OF_CONTROL
select SPL_DM_RESET if DM_RESET
select SPL_NAND_SUPPORT if SPL_NAND_DENALI
select SPL_OF_CONTROL
select SPL_SEPARATE_BSS if TARGET_SOCFPGA_SOC64
- select SPL_SERIAL_SUPPORT
+ select SPL_SERIAL
select SPL_SYSRESET
- select SPL_WATCHDOG_SUPPORT
+ select SPL_WATCHDOG
select SUPPORT_SPL
select SYS_NS16550
select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
imply SPL_DM_SPI
imply SPL_DM_SPI_FLASH
imply SPL_LIBDISK_SUPPORT
- imply SPL_MMC_SUPPORT
+ imply SPL_MMC
imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
imply SPL_SPI_FLASH_SUPPORT
- imply SPL_SPI_SUPPORT
+ imply SPL_SPI
imply L2X0_CACHE
config ARCH_SUNXI
select BINMAN
select CMD_GPIO
select CMD_MMC if MMC
- select CMD_USB if DISTRO_DEFAULTS
+ select CMD_USB if DISTRO_DEFAULTS && USB_HOST
select CLK
select DM
select DM_ETH
select DM_MMC if MMC
select DM_SCSI if SCSI
select DM_SERIAL
- select DM_USB if DISTRO_DEFAULTS
+ select GPIO_EXTRA_HEADER
select OF_BOARD_SETUP
select OF_CONTROL
select OF_SEPARATE
select SYS_NS16550
select SYS_THUMB_BUILD if !ARM64
select USB if DISTRO_DEFAULTS
- select USB_KEYBOARD if DISTRO_DEFAULTS
- select USB_STORAGE if DISTRO_DEFAULTS
+ select USB_KEYBOARD if DISTRO_DEFAULTS && USB_HOST
+ select USB_STORAGE if DISTRO_DEFAULTS && USB_HOST
select SPL_USE_TINY_PRINTF
select USE_PREBOOT
select SYS_RELOC_GD_ENV_ADDR
imply FIT
imply OF_LIBFDT_OVERLAY
imply PRE_CONSOLE_BUFFER
- imply SPL_GPIO_SUPPORT
+ imply SPL_GPIO
imply SPL_LIBCOMMON_SUPPORT
imply SPL_LIBGENERIC_SUPPORT
- imply SPL_MMC_SUPPORT if MMC
- imply SPL_POWER_SUPPORT
- imply SPL_SERIAL_SUPPORT
+ imply SPL_MMC if MMC
+ imply SPL_POWER
+ imply SPL_SERIAL
imply USB_GADGET
config ARCH_U8500
select DM_GPIO
select DM_MMC if MMC
select DM_SERIAL
- select DM_USB if USB
+ select DM_USB_GADGET if DM_USB
select OF_CONTROL
select SYSRESET
select TIMER
+ imply AB8500_USB_PHY
imply ARM_PL180_MMCI
+ imply CLK
+ imply DM_PMIC
imply DM_RTC
+ imply NOMADIK_GPIO
imply NOMADIK_MTU_TIMER
+ imply PHY
imply PL01X_SERIAL
+ imply PMIC_AB8500
imply RTC_PL031
+ imply SYS_THUMB_BUILD
imply SYSRESET_SYSCON
config ARCH_VERSAL
select DM_ETH if NET
select DM_MMC if MMC
select DM_SERIAL
+ select GICV3
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
+ select SOC_DEVICE
imply BOARD_LATE_INIT
imply ENV_VARS_UBOOT_RUNTIME_CONFIG
config ARCH_VF610
bool "Freescale Vybrid"
select CPU_V7A
+ select GPIO_EXTRA_HEADER
+ select MACH_IMX
select SYS_FSL_ERRATUM_ESDHC111
imply CMD_MTDPARTS
imply MTD_RAW_NAND
select DM_SERIAL
select DM_SPI
select DM_SPI_FLASH
- select DM_USB if USB
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select SPI
select SPL_BOARD_INIT if SPL
select DM_ETH if NET
select DM_MMC if MMC
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
imply CMD_DM
imply DM_USB_GADGET
select DM_SERIAL
select DM_SPI if SPI
select DM_SPI_FLASH if DM_SPI
- select DM_USB if USB
select FIRMWARE
+ select GICV2
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select SPL_BOARD_INIT if SPL
select SPL_CLK if SPL
select SPL_SEPARATE_BSS if SPL
select SUPPORT_SPL
select ZYNQMP_IPI
+ select SOC_DEVICE
imply BOARD_LATE_INIT
imply CMD_DM
imply ENV_VARS_UBOOT_RUNTIME_CONFIG
config ARCH_TEGRA
bool "NVIDIA Tegra"
+ select GPIO_EXTRA_HEADER
imply DISTRO_DEFAULTS
imply FAT_WRITE
config TARGET_VEXPRESS64_AEMV8A
bool "Support vexpress_aemv8a"
select ARM64
+ select GPIO_EXTRA_HEADER
select PL01X_SERIAL
config TARGET_VEXPRESS64_BASE_FVP
bool "Support Versatile Express ARMv8a FVP BASE model"
select ARM64
+ select GPIO_EXTRA_HEADER
select PL01X_SERIAL
select SEMIHOSTING
config TARGET_VEXPRESS64_JUNO
bool "Support Versatile Express Juno Development Platform"
select ARM64
+ select GPIO_EXTRA_HEADER
select PL01X_SERIAL
select DM
select OF_CONTROL
select DM_ETH
select BLK
select USB
- select DM_USB
config TARGET_TOTAL_COMPUTE
bool "Support Total Compute Platform"
select ARM64
select ARMV8_MULTIENTRY
select FSL_DDR_SYNC_REFRESH
+ select GPIO_EXTRA_HEADER
help
Support for Freescale LS2080A_EMU platform.
The LS2080A Development System (EMULATOR) is a pre-silicon
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
select SUPPORT_SPL
select FSL_DDR_INTERACTIVE if !SD_BOOT
help
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
select SUPPORT_SPL
imply SCSI
imply SCSI_AHCI
select SUPPORT_SPL
select FSL_DDR_BIST
select FSL_DDR_INTERACTIVE if !SPL
+ select GPIO_EXTRA_HEADER
imply SCSI
imply SCSI_AHCI
help
select ARM64
select ARMV8_MULTIENTRY
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
select SUPPORT_SPL
help
Support for Freescale LS2081ARDB platform.
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
help
Support for NXP LX2160ARDB platform.
The lx2160ardb (LX2160A Reference design board (RDB)
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
help
Support for NXP LX2160AQDS platform.
The lx2160aqds (LX2160A QorIQ Development System (QDS)
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
help
Support for NXP LX2162AQDS platform.
The lx2162aqds support is based on LX2160A Layerscape Architecture processor.
select DM
select DM_GPIO
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select PL01X_SERIAL
select SPECIFY_CONSOLE_INDEX
select ARM64
select DM
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select PL01X_SERIAL
imply CMD_DM
select ARM64
select DM
select DM_SERIAL
- select DM_USB
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select PL01X_SERIAL
imply CMD_DM
select ARM64
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
help
Support for Freescale LS1012AQDS platform.
The LS1012A Development System (QDS) is a high-performance
select ARM64
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
imply SCSI
imply SCSI_AHCI
help
select ARM64
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
imply SCSI
help
Support for Freescale LS1012A2G5RDB platform.
select ARM64
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
imply SCSI
imply SCSI_AHCI
help
select ARCH_LS1012A
select ARM64
select ARCH_SUPPORT_TFABOOT
+ select GPIO_EXTRA_HEADER
help
Support for Freescale LS1012AFRDM platform.
The LS1012A Freedom board (FRDM) is a high-performance
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
help
Support for Freescale LS1028AQDS platform
The LS1028A Development System (QDS) is a high-performance
select ARMV8_MULTIENTRY
select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
+ select GPIO_EXTRA_HEADER
help
Support for Freescale LS1028ARDB platform
The LS1028A Development System (RDB) is a high-performance
select BOARD_LATE_INIT
select SUPPORT_SPL
select FSL_DDR_INTERACTIVE if !SD_BOOT
+ select GPIO_EXTRA_HEADER
help
Support for NXP LS1088ARDB platform.
The LS1088A Reference design board (RDB) is a high-performance
select SYS_FSL_DDR
select FSL_DDR_INTERACTIVE
select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
+ select GPIO_EXTRA_HEADER
select SPI_FLASH_DATAFLASH if FSL_DSPI || FSL_QSPI
imply SCSI
select LS1_DEEP_SLEEP
select SUPPORT_SPL
select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
+ select GPIO_EXTRA_HEADER
imply SCSI
+config TARGET_PG_WCOM_SELI8
+ bool "Support Hitachi-Powergrids SELI8 service unit card"
+ select ARCH_LS1021A
+ select ARCH_SUPPORT_PSCI
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select CPU_V7A
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SYS_FSL_DDR
+ select FSL_DDR_INTERACTIVE
+ select GPIO_EXTRA_HEADER
+ select VENDOR_KM
+ imply SCSI
+ help
+ Support for Hitachi-Powergrids SELI8 service unit card.
+ SELI8 is a QorIQ LS1021a based service unit card used
+ in XMC20 and FOX615 product families.
+
+config TARGET_PG_WCOM_EXPU1
+ bool "Support Hitachi-Powergrids EXPU1 service unit card"
+ select ARCH_LS1021A
+ select ARCH_SUPPORT_PSCI
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select CPU_V7A
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SYS_FSL_DDR
+ select FSL_DDR_INTERACTIVE
+ select VENDOR_KM
+ imply SCSI
+ help
+ Support for Hitachi-Powergrids EXPU1 service unit card.
+ EXPU1 is a QorIQ LS1021a based service unit card used
+ in XMC20 and FOX615 product families.
+
config TARGET_LS1021ATSN
bool "Support ls1021atsn"
select ARCH_LS1021A
select CPU_V7_HAS_VIRT
select LS1_DEEP_SLEEP
select SUPPORT_SPL
+ select GPIO_EXTRA_HEADER
imply SCSI
config TARGET_LS1021AIOT
select CPU_V7_HAS_VIRT
select SUPPORT_SPL
select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
+ select GPIO_EXTRA_HEADER
imply SCSI
help
Support for Freescale LS1021AIOT platform.
select FSL_DDR_INTERACTIVE if !SPL
select FSL_DSPI if !SPL_NO_DSPI
select DM_SPI_FLASH if FSL_DSPI
+ select GPIO_EXTRA_HEADER
imply SCSI
imply SCSI_AHCI
help
select SUPPORT_SPL
select FSL_DSPI if !SPL_NO_DSPI
select DM_SPI_FLASH if FSL_DSPI
+ select GPIO_EXTRA_HEADER
help
Support for Freescale LS1043ARDB platform.
select FSL_DDR_BIST if !SPL
select FSL_DDR_INTERACTIVE if !SPL
select FSL_DDR_INTERACTIVE if !SPL
+ select GPIO_EXTRA_HEADER
imply SCSI
help
Support for Freescale LS1046AQDS platform.
select SUPPORT_SPL
select FSL_DDR_BIST
select FSL_DDR_INTERACTIVE if !SPL
+ select GPIO_EXTRA_HEADER
imply SCSI
help
Support for Freescale LS1046ARDB platform.
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select DM_SPI_FLASH if DM_SPI
+ select GPIO_EXTRA_HEADER
imply SCSI
help
Support for Freescale LS1046AFRWY platform.
select ARMV8_MULTIENTRY
select SUPPORT_SPL
select BINMAN
+ select DM
+ select DM_GPIO
+ select DM_I2C
+ select DM_MMC
+ select DM_SPI_FLASH
+ select DM_ETH
+ select DM_MDIO
+ select DM_PCI
+ select DM_RNG
+ select DM_RTC
+ select DM_SCSI
+ select DM_SERIAL
+ select DM_SPI
+ select GPIO_EXTRA_HEADER
+ select SPL_DM if SPL
+ select SPL_DM_SPI if SPL
+ select SPL_DM_SPI_FLASH if SPL
+ select SPL_DM_I2C if SPL
+ select SPL_DM_MMC if SPL
+ select SPL_DM_SERIAL if SPL
help
Support for Kontron SMARC-sAL28 board.
config TARGET_COLIBRI_PXA270
bool "Support colibri_pxa270"
select CPU_PXA
+ select GPIO_EXTRA_HEADER
config ARCH_UNIPHIER
bool "Socionext UniPhier SoCs"
select DM_MTD
select DM_RESET
select DM_SERIAL
- select DM_USB
select OF_BOARD_SETUP
select OF_CONTROL
select OF_LIBFDT
Support for UniPhier SoC family developed by Socionext Inc.
(formerly, System LSI Business Division of Panasonic Corporation)
+config ARCH_SYNQUACER
+ bool "Socionext SynQuacer SoCs"
+ select ARM64
+ select DM
+ select GIC_V3
+ select PSCI_RESET
+ select SYSRESET
+ select SYSRESET_PSCI
+ select OF_CONTROL
+ help
+ Support for SynQuacer SoC family developed by Socionext Inc.
+ This SoC is used on 96boards EE DeveloperBox.
+
config ARCH_STM32
bool "Support STMicroelectronics STM32 MCU with cortex M"
select CPU_V7M
select DM
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
imply CMD_DM
config ARCH_STI
select DM_GPIO
select DM_RESET
select DM_SERIAL
+ select GPIO_EXTRA_HEADER
select MISC
select OF_CONTROL
select OF_LIBFDT
config ARCH_ROCKCHIP
bool "Support Rockchip SoCs"
select BLK
- select BINMAN if SPL_OPTEE
+ select BINMAN if SPL_OPTEE || (SPL && !ARM64)
select DM
select DM_GPIO
select DM_I2C
select DM_SERIAL
select DM_SPI
select DM_SPI_FLASH
- select DM_USB if USB
select ENABLE_ARM_SOC_BOOT0_HOOK
select OF_CONTROL
select SPI
bool "Support OcteonTX SoCs"
select CLK
select DM
+ select GPIO_EXTRA_HEADER
select ARM64
select OF_CONTROL
select OF_LIVE
bool "Support OcteonTX2 SoCs"
select CLK
select DM
+ select GPIO_EXTRA_HEADER
select ARM64
select OF_CONTROL
select OF_LIVE
config TARGET_THUNDERX_88XX
bool "Support ThunderX 88xx"
select ARM64
+ select GPIO_EXTRA_HEADER
select OF_CONTROL
select PL01X_SERIAL
select SYS_CACHE_SHIFT_7
config TARGET_DURIAN
bool "Support Phytium Durian Platform"
select ARM64
+ select GPIO_EXTRA_HEADER
help
Support for durian platform.
It has 2GB Sdram, uart and pcie.
config TARGET_PRESIDIO_ASIC
bool "Support Cortina Presidio ASIC Platform"
select ARM64
+ select GICV2
config TARGET_XENGUEST_ARM64
bool "Xen guest ARM64"
config TFABOOT
bool "Support for booting from TF-A"
depends on ARCH_SUPPORT_TFABOOT
- default n
help
Some platforms support the setup of secure registers (for instance
for CPU errata handling) or provide secure services like PSCI.
source "arch/arm/mach-imx/imx8m/Kconfig"
+source "arch/arm/mach-imx/imx8ulp/Kconfig"
+
source "arch/arm/mach-imx/imxrt/Kconfig"
source "arch/arm/mach-imx/mxs/Kconfig"
source "board/bosch/guardian/Kconfig"
source "board/CarMediaLab/flea3/Kconfig"
source "board/Marvell/aspenite/Kconfig"
-source "board/Marvell/gplugd/Kconfig"
source "board/Marvell/octeontx/Kconfig"
source "board/Marvell/octeontx2/Kconfig"
-source "board/armltd/vexpress/Kconfig"
source "board/armltd/vexpress64/Kconfig"
source "board/cortina/presidio-asic/Kconfig"
-source "board/broadcom/bcm23550_w1d/Kconfig"
-source "board/broadcom/bcm28155_ap/Kconfig"
source "board/broadcom/bcm963158/Kconfig"
source "board/broadcom/bcm968360bg/Kconfig"
source "board/broadcom/bcm968580xref/Kconfig"
-source "board/broadcom/bcmcygnus/Kconfig"
-source "board/broadcom/bcmnsp/Kconfig"
-source "board/broadcom/bcmns2/Kconfig"
source "board/broadcom/bcmns3/Kconfig"
source "board/cavium/thunderx/Kconfig"
-source "board/cirrus/edb93xx/Kconfig"
source "board/eets/pdu001/Kconfig"
source "board/emulation/qemu-arm/Kconfig"
source "board/freescale/ls2080aqds/Kconfig"
source "board/freescale/ls1012ardb/Kconfig"
source "board/freescale/ls1012afrdm/Kconfig"
source "board/freescale/lx2160a/Kconfig"
-source "board/freescale/s32v234evb/Kconfig"
source "board/grinn/chiliboard/Kconfig"
source "board/hisilicon/hikey/Kconfig"
source "board/hisilicon/hikey960/Kconfig"
source "board/isee/igep003x/Kconfig"
source "board/kontron/sl28/Kconfig"
source "board/myir/mys_6ulx/Kconfig"
-source "board/spear/spear300/Kconfig"
-source "board/spear/spear310/Kconfig"
-source "board/spear/spear320/Kconfig"
-source "board/spear/spear600/Kconfig"
-source "board/spear/x600/Kconfig"
+source "board/seeed/npi_imx6ull/Kconfig"
+source "board/socionext/developerbox/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/tcl/sl50/Kconfig"
source "board/toradex/colibri_pxa270/Kconfig"
source "board/vscom/baltos/Kconfig"
source "board/phytium/durian/Kconfig"
source "board/xen/xenguest_arm64/Kconfig"
+source "board/keymile/Kconfig"
source "arch/arm/Kconfig.debug"