In this mode, a single differential clock is used to supply
clocks to the sysclock, ddrclock and usbclock.
- CONFIG_SYS_CPC_REINIT_F
- This CONFIG is defined when the CPC is configured as SRAM at the
- time of U-Boot entry and is required to be re-initialized.
-
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
CONFIG_SYS_FSL_DDR_ADDR
Freescale DDR memory-mapped register base.
- CONFIG_SYS_FSL_DDR_EMU
- Specify emulator support for DDR. Some DDR features such as
- deskew training are not available.
-
CONFIG_SYS_FSL_DDRC_GEN1
Freescale DDR1 controller.
the appropriate value in Hz.
- MMC Support:
- The MMC controller on the Intel PXA is supported. To
- enable this define CONFIG_MMC. The MMC can be
- accessed from the boot prompt by mapping the device
- to physical memory similar to flash. Command line is
- enabled with CONFIG_CMD_MMC. The MMC driver also works with
- the FAT fs. This is enabled with CONFIG_CMD_FAT.
-
CONFIG_SH_MMCIF
Support for Renesas on-chip MMCIF controller
will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
- CONFIG_SYS_SPD_BUS_NUM
-
- If defined, then this indicates the I2C bus number for DDR SPD.
- If not defined, then U-Boot assumes that SPD is on I2C bus 0.
-
CONFIG_SYS_RTC_BUS_NUM
If defined, then this indicates the I2C bus number for the RTC.
overwriting the architecture dependent default
settings.
-- Frame Buffer Address:
- CONFIG_FB_ADDR
-
- Define CONFIG_FB_ADDR if you want to use specific
- address for frame buffer. This is typically the case
- when using a graphics controller has separate video
- memory. U-Boot will then place the frame buffer at
- the given address instead of dynamically reserving it
- in system RAM by calling lcd_setmem(), which grabs
- the memory for the frame buffer depending on the
- configured panel size.
-
- Please see board_init_f function.
-
- Automatic software updates via TFTP server
CONFIG_UPDATE_TFTP
CONFIG_UPDATE_TFTP_CNT_MAX
Non-cached memory is only supported on 32-bit ARM at present.
-- CONFIG_SYS_BOOTM_LEN:
- Normally compressed uImages are limited to an
- uncompressed size of 8 MBytes. If this is not enough,
- you can define CONFIG_SYS_BOOTM_LEN in your board config file
- to adjust this setting to your needs.
-
- CONFIG_SYS_BOOTMAPSZ:
Maximum size of memory mapped by the startup code of
the Linux kernel; all data that must be processed by
CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
then the value in "bootm_size" will be used instead.
-- CONFIG_SYS_BOOT_RAMDISK_HIGH:
- Enable initrd_high functionality. If defined then the
- initrd_high feature is enabled and the bootm ramdisk subcommand
- is enabled.
-
- CONFIG_SYS_BOOT_GET_CMDLINE:
Enables allocating and saving kernel cmdline in space between
"bootm_low" and "bootm_low" + BOOTMAPSZ.
one, specify here. Note that the value must resolve
to something your driver can deal with.
-- CONFIG_SYS_DDR_RAW_TIMING
- Get DDR timing information from other than SPD. Common with
- soldered DDR chips onboard without SPD. DDR raw timing
- parameters are extracted from datasheet and hard-coded into
- header files or board specific files.
-
- CONFIG_FSL_DDR_INTERACTIVE
Enable interactive DDR debugging. See doc/README.fsl-ddr.
- CONFIG_FSL_DDR_BIST
Enable built-in memory test for Freescale DDR controllers.
-- CONFIG_SYS_83XX_DDR_USES_CS0
- Only for 83xx systems. If specified, then DDR should
- be configured using CS0 and CS1 instead of CS2 and CS3.
-
- CONFIG_RMII
Enable RMII mode for all FECs.
Note that this is a global option, we can't