vbe: Drop the U-Boot prefix from the version

[platform/kernel/u-boot.git] / README

diff --git a/README b/README
index 4ef9e8c..ec1b50c 100644 (file)
--- a/README
+++ b/README
@@ -294,12 +294,6 @@ The following options need to be configured:
                the "64" category of the Power ISA). This is necessary for ePAPR
                compliance, among other possible reasons.
 
-               CONFIG_SYS_FSL_TBCLK_DIV
-
-               Defines the core time base clock divider ratio compared to the
-               system clock.  On most PQ3 devices this is 8, on newer QorIQ
-               devices it can be 16 or 32.  The ratio varies from SoC to Soc.
-
                CONFIG_SYS_FSL_ERRATUM_A004510
 
                Enables a workaround for erratum A004510.  If set,
@@ -421,8 +415,6 @@ The following options need to be configured:
                the defaults discussed just above.
 
 - Cache Configuration for ARM:
-               CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
-                                     controller
                CONFIG_SYS_PL310_BASE - Physical base address of PL310
                                        controller register space
 
@@ -571,20 +563,6 @@ The following options need to be configured:
                        CONFIG_LAN91C96_USE_32_BIT
                        Define this to enable 32 bit addressing
 
-               CONFIG_SMC91111
-               Support for SMSC's LAN91C111 chip
-
-                       CONFIG_SMC91111_BASE
-                       Define this to hold the physical address
-                       of the device (I/O space)
-
-                       CONFIG_SMC_USE_32_BIT
-                       Define this if data bus is 32 bits
-
-                       CONFIG_SMC_USE_IOFUNCS
-                       Define this to use i/o functions instead of macros
-                       (some hardware wont work with macros)
-
                        CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
                        Define this if you have more then 3 PHYs.
 
@@ -792,80 +770,6 @@ The following options need to be configured:
 - Keyboard Support:
                See Kconfig help for available keyboard drivers.
 
-- LCD Support: CONFIG_LCD
-
-               Define this to enable LCD support (for output to LCD
-               display); also select one of the supported displays
-               by defining one of these:
-
-               CONFIG_NEC_NL6448AC33:
-
-                       NEC NL6448AC33-18. Active, color, single scan.
-
-               CONFIG_NEC_NL6448BC20
-
-                       NEC NL6448BC20-08. 6.5", 640x480.
-                       Active, color, single scan.
-
-               CONFIG_NEC_NL6448BC33_54
-
-                       NEC NL6448BC33-54. 10.4", 640x480.
-                       Active, color, single scan.
-
-               CONFIG_SHARP_16x9
-
-                       Sharp 320x240. Active, color, single scan.
-                       It isn't 16x9, and I am not sure what it is.
-
-               CONFIG_SHARP_LQ64D341
-
-                       Sharp LQ64D341 display, 640x480.
-                       Active, color, single scan.
-
-               CONFIG_HLD1045
-
-                       HLD1045 display, 640x480.
-                       Active, color, single scan.
-
-               CONFIG_OPTREX_BW
-
-                       Optrex   CBL50840-2 NF-FW 99 22 M5
-                       or
-                       Hitachi  LMG6912RPFC-00T
-                       or
-                       Hitachi  SP14Q002
-
-                       320x240. Black & white.
-
-               CONFIG_LCD_ALIGNMENT
-
-               Normally the LCD is page-aligned (typically 4KB). If this is
-               defined then the LCD will be aligned to this value instead.
-               For ARM it is sometimes useful to use MMU_SECTION_SIZE
-               here, since it is cheaper to change data cache settings on
-               a per-section basis.
-
-
-               CONFIG_LCD_ROTATION
-
-               Sometimes, for example if the display is mounted in portrait
-               mode or even if it's mounted landscape but rotated by 180degree,
-               we need to rotate our content of the display relative to the
-               framebuffer, so that user can read the messages which are
-               printed out.
-               Once CONFIG_LCD_ROTATION is defined, the lcd_console will be
-               initialized with a given rotation from "vl_rot" out of
-               "vidinfo_t" which is provided by the board specific code.
-               The value for vl_rot is coded as following (matching to
-               fbcon=rotate:<n> linux-kernel commandline):
-               0 = no rotation respectively 0 degree
-               1 = 90 degree rotation
-               2 = 180 degree rotation
-               3 = 270 degree rotation
-
-               If CONFIG_LCD_ROTATION is not defined, the console will be
-               initialized with 0degree rotation.
-
 - MII/PHY support:
                CONFIG_PHY_CLOCK_FREQ (ppc4xx)