Fix loading freeze when netconsole is active

[platform/kernel/u-boot.git] / README

diff --git a/README b/README
index 301d1a9..ccd47fa 100644 (file)
--- a/README
+++ b/README
@@ -35,7 +35,7 @@ Makefile have been tested to some extent and can be considered
 "working". In fact, many of them are used in production systems.
 
 In case of problems see the CHANGELOG and CREDITS files to find out
-who contributed the specific port. The MAINTAINERS file lists board
+who contributed the specific port. The boards.cfg file lists board
 maintainers.
 
 Note: There is no CHANGELOG file in the actual U-Boot source tree;
@@ -1680,6 +1680,10 @@ CBFS (Coreboot Filesystem) support
                to compress the specified memory at its best effort.
 
 - Compression support:
+               CONFIG_GZIP
+
+               Enabled by default to support gzip compressed images.
+
                CONFIG_BZIP2
 
                If this option is set, support for bzip2 compressed
@@ -1713,6 +1717,11 @@ CBFS (Coreboot Filesystem) support
                then calculate the amount of needed dynamic memory (ensuring
                the appropriate CONFIG_SYS_MALLOC_LEN value).
 
+               CONFIG_LZO
+
+               If this option is set, support for LZO compressed images
+               is included.
+
 - MII/PHY support:
                CONFIG_PHY_ADDR
 
@@ -3094,6 +3103,10 @@ FIT uImage format:
                Set for the SPL on PPC mpc8xxx targets, support for
                arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
 
+               CONFIG_SPL_COMMON_INIT_DDR
+               Set for common ddr init with serial presence detect in
+               SPL binary.
+
                CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
                CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
                CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
@@ -3163,6 +3176,17 @@ FIT uImage format:
                option to re-enable it. This will affect the output of the
                bootm command when booting a FIT image.
 
+- TPL framework
+               CONFIG_TPL
+               Enable building of TPL globally.
+
+               CONFIG_TPL_PAD_TO
+               Image offset to which the TPL should be padded before appending
+               the TPL payload. By default, this is defined as
+                CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
+                CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
+                payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
+
 Modem Support:
 --------------
 
@@ -4200,6 +4224,11 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
+- CONFIG_TPL_BUILD
+               Modifies the behaviour of start.S  when compiling a loader
+               that is executed after the SPL and before the actual U-Boot.
+               It is loaded by the SPL.
+
 - CONFIG_SYS_MPC85XX_NO_RESETVEC
                Only for 85xx systems. If this variable is specified, the section
                .resetvec is not kept and the section .bootpg is placed in the
@@ -5804,8 +5833,8 @@ it:
 
 * For major contributions, your entry to the CREDITS file
 
-* When you add support for a new board, don't forget to add this
-  board to the MAINTAINERS file, too.
+* When you add support for a new board, don't forget to add a
+  maintainer e-mail address to the boards.cfg file, too.
 
 * If your patch adds new configuration options, don't forget to
   document these in the README file.