PBI commands can be used to configure SoC before it starts the execution.
Please refer doc/README.pblimage for more details
+ CONFIG_SYS_FSL_DDR_BE
+ Defines the DDR controller register space as Big Endian
+
+ CONFIG_SYS_FSL_DDR_LE
+ Defines the DDR controller register space as Little Endian
+
+ CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
+ Physical address from the view of DDR controllers. It is the
+ same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
+ it could be different for ARM SoCs.
+
+ CONFIG_SYS_FSL_DDR_INTLV_256B
+ DDR controller interleaving on 256-byte. This is a special
+ interleaving mode, handled by Dickens for Freescale layerscape
+ SoCs with ARM core.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_ARM_ERRATA_742230
CONFIG_ARM_ERRATA_743622
CONFIG_ARM_ERRATA_751472
+ CONFIG_ARM_ERRATA_794072
+ CONFIG_ARM_ERRATA_761320
If set, the workarounds for these ARM errata are applied early
during U-Boot startup. Note that these options force the
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT command support
- CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_FUSE * Device fuse support
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_MFSL * Microblaze FSL support
CONFIG_CMD_XIMG Load part of Multi Image
-
+ CONFIG_CMD_UUID * Generate random UUID or GUID string
EXAMPLE: If you want all functions except of network
support you can write:
this to the maximum filesize (in bytes) for the buffer.
Default is 4 MiB if undefined.
+ DFU_DEFAULT_POLL_TIMEOUT
+ Poll timeout [ms], is the timeout a device can send to the
+ host. The host must wait for this timeout before sending
+ a subsequent DFU_GET_STATUS request to the device.
+
+ DFU_MANIFEST_POLL_TIMEOUT
+ Poll timeout [ms], which the device sends to the host when
+ entering dfuMANIFEST state. Host waits this timeout, before
+ sending again an USB request to the device.
+
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
CONFIG_JFFS2_NAND_DEV
The signing part is build into mkimage regardless of this
option.
+- bootcount support:
+ CONFIG_BOOTCOUNT_LIMIT
+
+ This enables the bootcounter support, see:
+ http://www.denx.de/wiki/DULG/UBootBootCountLimit
+
+ CONFIG_AT91SAM9XE
+ enable special bootcounter support on at91sam9xe based boards.
+ CONFIG_BLACKFIN
+ enable special bootcounter support on blackfin based boards.
+ CONFIG_SOC_DA8XX
+ enable special bootcounter support on da850 based boards.
+ CONFIG_BOOTCOUNT_RAM
+ enable support for the bootcounter in RAM
+ CONFIG_BOOTCOUNT_I2C
+ enable support for the bootcounter on an i2c (like RTC) device.
+ CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
+ CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
+ the bootcounter.
+ CONFIG_BOOTCOUNT_ALEN = address len
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
supports MMC, NAND and YMODEM loading of U-Boot and NAND
NAND loading of the Linux Kernel.
+ CONFIG_SPL_OS_BOOT
+ Enable booting directly to an OS from SPL.
+ See also: doc/README.falcon
+
CONFIG_SPL_DISPLAY_PRINT
For ARM, enable an optional function to print more information
about the running system.
Support for NAND boot using simple NAND drivers that
expose the cmd_ctrl() interface.
+ CONFIG_SPL_MTD_SUPPORT
+ Support for the MTD subsystem within SPL. Useful for
+ environment on NAND support within SPL.
+
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
Set for the SPL on PPC mpc8xxx targets, support for
drivers/ddr/fsl/libddr.o in SPL binary.
Configuration Settings:
-----------------------
+- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+ Optionally it can be defined to support 64-bit memory commands.
+
- CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
undefine this when you're short of memory.
- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
Enables the RTC32K OSC on AM33xx based plattforms
+- CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
+ Option to disable subpage write in NAND driver
+ driver that uses this:
+ drivers/mtd/nand/davinci_nand.c
+
Freescale QE/FMAN Firmware Support:
-----------------------------------