/blackfin Files generic to Analog Devices Blackfin architecture
/cpu CPU specific files
/lib Architecture specific library files
- /i386 Files generic to i386 architecture
+ /x86 Files generic to x86 architecture
/cpu CPU specific files
/lib Architecture specific library files
/m68k Files generic to m68k architecture
CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
CONFIG_SYS_8272ADS - MPC8272ADS
+- Marvell Family Member
+ CONFIG_SYS_MVFS - define it if you want to enable
+ multiple fs option at one time
+ for marvell soc family
+
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
+ CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
+ CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT partition support
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
+ CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all found images
CONFIG_CMD_IMMAP * IMMR dump support
+ CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
+ CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
- CONFIG_CMD_SHA1 print sha1 memory digest
+ CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
+ CONFIG_SYS_RV3029_TCR - enable trickle charger on
+ RV3029 RTC.
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
CONFIG_PCA953X_INFO - enable pca953x info command
+ The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
+ chip-ngpio pairs that tell the PCA953X driver the number of
+ pins supported by a particular chip.
+
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
+ CONFIG_FTGMAC100
+ Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
+
+ CONFIG_FTGMAC100_EGIGA
+ Define this to use GE link update with gigabit PHY.
+ Define this if FTGMAC100 is connected to gigabit PHY.
+ If your system has 10/100 PHY only, it might not occur
+ wrong behavior. Because PHY usually return timeout or
+ useless data when polling gigabit status and gigabit
+ control registers. This behavior won't affect the
+ correctnessof 10/100 link speed update.
+
CONFIG_SMC911X
Support for SMSC's LAN911x and LAN921x chips
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
+ CONFIG_SH_ETHER
+ Support for Renesas on-chip Ethernet controller
+
+ CONFIG_SH_ETHER_USE_PORT
+ Define the number of ports to be used
+
+ CONFIG_SH_ETHER_PHY_ADDR
+ Define the ETH PHY's address
+
+ CONFIG_SH_ETHER_CACHE_WRITEBACK
+ If this option is set, the driver enables cache flush.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
or CONFIG_VIDEO_SED13806_16BPP
+ CONFIG_FSL_DIU_FB
+ Enable the Freescale DIU video driver. Reference boards for
+ SOCs that have a DIU should define this macro to enable DIU
+ support, and should also define these other macros:
+
+ CONFIG_SYS_DIU_ADDR
+ CONFIG_VIDEO
+ CONFIG_CMD_BMP
+ CONFIG_CFB_CONSOLE
+ CONFIG_VIDEO_SW_CURSOR
+ CONFIG_VGA_AS_SINGLE_DEVICE
+ CONFIG_VIDEO_LOGO
+ CONFIG_VIDEO_BMP_LOGO
+
+ The DIU driver will look for the 'monitor' environment variable,
+ and if defined, enable the DIU as a console during boot. This
+ variable should be set to one of these values:
+
+ '0' Output video to the DVI connector
+ '1' Output video to the LVDS connector
+ '2' Output video to the Dual-Link LVDS connector
+
- Keyboard Support:
CONFIG_KEYBOARD
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
+ CONFIG_SH_SPI
+
+ Enables the driver for SPI controller on SuperH. Currently
+ only SH7757 is supported.
+
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
+- Standalone program support:
+ CONFIG_STANDALONE_LOAD_ADDR
+
+ This option allows to define board specific values
+ for the address where standalone program gets loaded,
+ thus overwriting the architecutre dependent default
+ settings.
+
+- Frame Buffer Address:
+ CONFIG_FB_ADDR
+
+ Define CONFIG_FB_ADDR if you want to use specific address for
+ frame buffer.
+ Then system will reserve the frame buffer address to defined address
+ instead of lcd_setmem (this function grab the memory for frame buffer
+ by panel's size).
+
+ Please see board_init_f function.
+
+ If you want this config option then,
+ please define it at your board config file
+
Legacy uImage format:
Arg Where When
all data for the Linux kernel must be between "bootm_low"
and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+- CONFIG_SYS_BOOT_RAMDISK_HIGH:
+ Enable initrd_high functionality. If defined then the
+ initrd_high feature is enabled and the bootm ramdisk subcommand
+ is enabled.
+
+- CONFIG_SYS_BOOT_GET_CMDLINE:
+ Enables allocating and saving kernel cmdline in space between
+ "bootm_low" and "bootm_low" + BOOTMAPSZ.
+
+- CONFIG_SYS_BOOT_GET_KBD:
+ Enables allocating and saving a kernel copy of the bd_info in
+ space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
+
- CONFIG_SYS_MAX_FLASH_BANKS:
Max number of Flash memory banks
- CONFIG_ENV_MAX_ENTRIES
- Maximum number of entries in the hash table that is used
- internally to store the environment settings. The default
- setting is supposed to be generous and should work in most
- cases. This setting can be used to tune behaviour; see
- lib/hashtable.c for details.
+ Maximum number of entries in the hash table that is used
+ internally to store the environment settings. The default
+ setting is supposed to be generous and should work in most
+ cases. This setting can be used to tune behaviour; see
+ lib/hashtable.c for details.
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
data is located at the end of the available space
- (sometimes written as (CONFIG_SYS_INIT_RAM_END -
+ (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_GBL_DATA_OFFSET) downward.
Disable PCI-Express on systems where it is supported but not
required.
+- CONFIG_SYS_SRIO:
+ Chip has SRIO or not
+
+- CONFIG_SRIO1:
+ Board has SRIO 1 port available
+
+- CONFIG_SRIO2:
+ Board has SRIO 2 port available
+
+- CONFIG_SYS_SRIOn_MEM_VIRT:
+ Virtual Address of SRIO port 'n' memory region
+
+- CONFIG_SYS_SRIOn_MEM_PHYS:
+ Physical Address of SRIO port 'n' memory region
+
+- CONFIG_SYS_SRIOn_MEM_SIZE:
+ Size of SRIO port 'n' memory region
+
- CONFIG_SPD_EEPROM
Get DDR timing information from an I2C EEPROM. Common
with pluggable memory modules such as SODIMMs
globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT
-- CONFIG_SKIP_RELOCATE_UBOOT
+ [ARM only] If this variable is defined, then certain
+ low level initializations (like setting up the memory
+ controller) are omitted and/or U-Boot does not
+ relocate itself into RAM.
- [ARM only] If these variables are defined, then
- certain low level initializations (like setting up
- the memory controller) are omitted and/or U-Boot does
- not relocate itself into RAM.
- Normally these variables MUST NOT be defined. The
- only exception is when U-Boot is loaded (to RAM) by
- some other boot loader or by a debugger which
- performs these initializations itself.
+ Normally this variable MUST NOT be defined. The only
+ exception is when U-Boot is loaded (to RAM) by some
+ other boot loader or by a debugger which performs
+ these initializations itself.
- CONFIG_PRELOADER
-
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_USE_ARCH_MEMCPY
+ CONFIG_USE_ARCH_MEMSET
+ If these options are used a optimized version of memcpy/memset will
+ be used if available. These functions may be faster under some
+ conditions but may increase the binary size.
+
Building the Software:
======================