/m68k Files generic to m68k architecture
/microblaze Files generic to microblaze architecture
/mips Files generic to MIPS architecture
- /nds32 Files generic to NDS32 architecture
/nios2 Files generic to Altera NIOS2 architecture
/powerpc Files generic to PowerPC architecture
/riscv Files generic to RISC-V architecture
See Freescale App Note 4493 for more information about
this erratum.
- CONFIG_A003399_NOR_WORKAROUND
- Enables a workaround for IFC erratum A003399. It is only
- required during NOR boot.
-
- CONFIG_A008044_WORKAROUND
- Enables a workaround for T1040/T1042 erratum A008044. It is only
- required during NAND boot and valid for Rev 1.0 SoC revision
-
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
This is the value to write into CCSR offset 0x18600
This CONFIG is defined when the CPC is configured as SRAM at the
time of U-Boot entry and is required to be re-initialized.
- CONFIG_DEEP_SLEEP
- Indicates this SoC supports deep sleep feature. If deep sleep is
- supported, core will start to execute uboot when wakes up.
-
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
Number of controllers used for other than main memory.
- CONFIG_SYS_FSL_HAS_DP_DDR
- Defines the SoC has DP-DDR used for DPAA.
-
CONFIG_SYS_FSL_SEC_BE
Defines the SEC controller register space as Big Endian
- Keyboard Support:
See Kconfig help for available keyboard drivers.
-- Video support:
- CONFIG_FSL_DIU_FB
- Enable the Freescale DIU video driver. Reference boards for
- SOCs that have a DIU should define this macro to enable DIU
- support, and should also define these other macros:
-
- CONFIG_SYS_DIU_ADDR
- CONFIG_VIDEO
- CONFIG_CFB_CONSOLE
- CONFIG_VIDEO_SW_CURSOR
- CONFIG_VGA_AS_SINGLE_DEVICE
- CONFIG_VIDEO_BMP_LOGO
-
- The DIU driver will look for the 'video-mode' environment
- variable, and if defined, enable the DIU as a console during
- boot. See the documentation file doc/README.video for a
- description of this variable.
-
- LCD Support: CONFIG_LCD
Define this to enable LCD support (for output to LCD
display); also select one of the supported displays
by defining one of these:
- CONFIG_ATMEL_LCD:
-
- HITACHI TX09D70VM1CCA, 3.5", 240x320.
-
CONFIG_NEC_NL6448AC33:
NEC NL6448AC33-18. Active, color, single scan.
If CONFIG_LCD_ROTATION is not defined, the console will be
initialized with 0degree rotation.
- CONFIG_LCD_BMP_RLE8
-
- Support drawing of RLE8-compressed bitmaps on the LCD.
-
- MII/PHY support:
CONFIG_PHY_CLOCK_FREQ (ppc4xx)
The clock frequency of the MII bus
- CONFIG_PHY_RESET_DELAY
-
- Some PHY like Intel LXT971A need extra delay after
- reset before any MII register access is possible.
- For such PHY, set this option to the usec delay
- required. (minimum 300usec for LXT971A)
-
CONFIG_PHY_CMD_DELAY (ppc4xx)
Some PHY like Intel LXT971A need extra delay after
FLAGADM
- Error Recovery:
- CONFIG_NET_RETRY_COUNT
-
- This variable defines the number of retries for
- network operations like ARP, RARP, TFTP, or BOOTP
- before giving up the operation. If not defined, a
- default value of 5 is used.
-
- CONFIG_ARP_TIMEOUT
-
- Timeout waiting for an ARP reply in milliseconds.
-
- CONFIG_NFS_TIMEOUT
-
- Timeout in milliseconds used in NFS protocol.
- If you encounter "ERROR: Cannot umount" in nfs command,
- try longer timeout such as
- #define CONFIG_NFS_TIMEOUT 10000UL
-
Note:
In the current implementation, the local variables
of the backslashes before semicolons and special
symbols.
-- Command Line Editing and History:
- CONFIG_CMDLINE_PS_SUPPORT
-
- Enable support for changing the command prompt string
- at run-time. Only static string is supported so far.
- The string is obtained from environment variables PS1
- and PS2.
-
- Default Environment:
CONFIG_EXTRA_ENV_SETTINGS
this is instead controlled by the value of
/config/load-environment.
-- TFTP Fixed UDP Port:
- CONFIG_TFTP_PORT
-
- If this is defined, the environment variable tftpsrcp
- is used to supply the TFTP UDP source port value.
- If tftpsrcp isn't defined, the normal pseudo-random port
- number generator is used.
-
- Also, the environment variable tftpdstp is used to supply
- the TFTP UDP destination port value. If tftpdstp isn't
- defined, the normal port 69 is used.
-
- The purpose for tftpsrcp is to allow a TFTP server to
- blindly start the TFTP transfer using the pre-configured
- target IP address and UDP port. This has the effect of
- "punching through" the (Windows XP) firewall, allowing
- the remainder of the TFTP transfer to proceed normally.
- A better solution is to properly configure the firewall,
- but sometimes that is not allowed.
-
CONFIG_STANDALONE_LOAD_ADDR
This option defines a board specific value for the
the RAM base is not zero, or RAM is divided into banks,
this variable needs to be recalcuated to get the address.
-- CONFIG_SYS_MEM_TOP_HIDE:
- If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
- this specified memory area will get subtracted from the top
- (end) of RAM and won't get "touched" at all by U-Boot. By
- fixing up gd->ram_size the Linux kernel should gets passed
- the now "corrected" memory size and won't touch it either.
- This should work for arch/ppc and arch/powerpc. Only Linux
- board ports in arch/powerpc with bootwrapper support that
- recalculate the memory size from the SDRAM controller setup
- will have to get fixed in Linux additionally.
-
- This option can be used as a workaround for the 440EPx/GRx
- CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
- be touched.
-
- WARNING: Please make sure that this value is a multiple of
- the Linux page size (normally 4k). If this is not the case,
- then the end address of the Linux memory will be located at a
- non page size aligned address and this could cause major
- problems.
-
- CONFIG_SYS_LOADS_BAUD_CHANGE:
Enable temporary baudrate change while serial download
- CONFIG_SYS_FLASH_BASE:
Physical start address of Flash memory.
-- CONFIG_SYS_MONITOR_BASE:
- Physical start address of boot monitor code (set by
- make config files to be same as the text base address
- (CONFIG_SYS_TEXT_BASE) used when linking) - same as
- CONFIG_SYS_FLASH_BASE when booting from flash.
-
- CONFIG_SYS_MONITOR_LEN:
Size of memory reserved for monitor code, used to
determine _at_compile_time_ (!) if the environment is
while unprotecting/erasing/programming. Please only enable
this option if you really know what you are doing.
-- CONFIG_SYS_RX_ETH_BUFFER:
- Defines the number of Ethernet receive buffers. On some
- Ethernet controllers it is recommended to set this value
- to 8 or even higher (EEPRO100 or 405 EMAC), since all
- buffers can be full shortly after enabling the interface
- on high Ethernet traffic.
- Defaults to 4 if not defined.
-
- CONFIG_ENV_MAX_ENTRIES
Maximum number of entries in the hash table that is used
the default environment is used; a new CRC is computed as soon as you
use the "saveenv" command to store a valid environment.
-- CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
- Echo the inverted Ethernet link state to the fault LED.
-
- Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
- also needs to be defined.
-
- CONFIG_SYS_FAULT_MII_ADDR:
MII address of the PHY to check for the Ethernet link state.
later, once stdio is running and output goes to the LCD, if
present.
-- CONFIG_BOARD_SIZE_LIMIT:
- Maximum size of the U-Boot image. When defined, the
- build system checks that the actual size does not
- exceed it.
-
Low Level (hardware related) configuration options:
---------------------------------------------------
LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, INTEGRITY).
* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
- IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
- Currently supported: ARM, Intel x86, MIPS, NDS32, Nios II, PowerPC).
+ IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
+ Currently supported: ARM, Intel x86, MIPS, Nios II, PowerPC).
* Compression Type (uncompressed, gzip, bzip2)
* Load Address
* Entry Point
Note: on Nios II, we give "-G0" option to gcc and don't use gp
to access small data sections, so gp is free.
-On NDS32, the following registers are used:
-
- R0-R1: argument/return
- R2-R5: argument
- R15: temporary register for assembler
- R16: trampoline register
- R28: frame pointer (FP)
- R29: global pointer (GP)
- R30: link register (LP)
- R31: stack pointer (SP)
- PC: program counter (PC)
-
- ==> U-Boot will use R10 to hold a pointer to the global data
-
-NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
-or current versions of GCC may "optimize" the code too much.
-
On RISC-V, the following registers are used:
x0: hard-wired zero (zero)
projects / platform / kernel / u-boot.git / blobdiff