samsung: tizen_amlogic: increase ramdisk size from 8M to 32M

[platform/kernel/u-boot.git] / README

diff --git a/README b/README
index 7ab7e37..b23fcc1 100644 (file)
--- a/README
+++ b/README
@@ -266,7 +266,7 @@ board_init_f():
                version as needed.
        - preloader_console_init() can be called here in extremis
        - should set up SDRAM, and anything needed to make the UART work
-       - these is no need to clear BSS, it will be done by crt0.S
+       - there is no need to clear BSS, it will be done by crt0.S
        - for specific scenarios on certain architectures an early BSS *can*
          be made available (via CONFIG_SPL_EARLY_BSS by moving the clearing
          of BSS prior to entering board_init_f()) but doing so is discouraged.
@@ -1250,48 +1250,6 @@ The following options need to be configured:
                Enables an 'i2c edid' command which can read EDID
                information over I2C from an attached LCD display.
 
-- Splash Screen Support: CONFIG_SPLASH_SCREEN
-
-               If this option is set, the environment is checked for
-               a variable "splashimage". If found, the usual display
-               of logo, copyright and system information on the LCD
-               is suppressed and the BMP image at the address
-               specified in "splashimage" is loaded instead. The
-               console is redirected to the "nulldev", too. This
-               allows for a "silent" boot where a splash screen is
-               loaded very quickly after power-on.
-
-               CONFIG_SPLASHIMAGE_GUARD
-
-               If this option is set, then U-Boot will prevent the environment
-               variable "splashimage" from being set to a problematic address
-               (see doc/README.displaying-bmps).
-               This option is useful for targets where, due to alignment
-               restrictions, an improperly aligned BMP image will cause a data
-               abort. If you think you will not have problems with unaligned
-               accesses (for example because your toolchain prevents them)
-               there is no need to set this option.
-
-               CONFIG_SPLASH_SCREEN_ALIGN
-
-               If this option is set the splash image can be freely positioned
-               on the screen. Environment variable "splashpos" specifies the
-               position as "x,y". If a positive number is given it is used as
-               number of pixel from left/top. If a negative number is given it
-               is used as number of pixel from right/bottom. You can also
-               specify 'm' for centering the image.
-
-               Example:
-               setenv splashpos m,m
-                       => image at center of screen
-
-               setenv splashpos 30,20
-                       => image at x = 30 and y = 20
-
-               setenv splashpos -10,m
-                       => vertically centered image
-                          at x = dspWidth - bmpWidth - 9
-
 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
 
                If this option is set, additionally to standard BMP
@@ -1401,7 +1359,6 @@ The following options need to be configured:
 
                CONFIG_BOOTP_NISDOMAIN
                CONFIG_BOOTP_BOOTFILESIZE
-               CONFIG_BOOTP_SEND_HOSTNAME
                CONFIG_BOOTP_NTPSERVER
                CONFIG_BOOTP_TIMEOFFSET
                CONFIG_BOOTP_VENDOREX
@@ -1416,13 +1373,6 @@ The following options need to be configured:
                to Link-local IP address configuration if the DHCP server
                is not available.
 
-               CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
-               to do a dynamic update of a DNS server. To do this, they
-               need the hostname of the DHCP requester.
-               If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
-               of the "hostname" environment variable is passed as
-               option 12 to the DHCP server.
-
                CONFIG_BOOTP_DHCP_REQUEST_DELAY
 
                A 32bit value in microseconds for a delay between
@@ -2257,10 +2207,6 @@ The following options need to be configured:
                parameters from when MMC is being used in raw mode
                (for falcon mode)
 
-               CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
-               Partition on the MMC to load U-Boot from when the MMC is being
-               used in fs mode
-
                CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from filesystem
 
@@ -2281,24 +2227,10 @@ The following options need to be configured:
                CONFIG_SPL_SKIP_RELOCATE
                Avoid SPL relocation
 
-               CONFIG_SPL_NAND_BASE
-               Include nand_base.c in the SPL.  Requires
-               CONFIG_SPL_NAND_DRIVERS.
-
-               CONFIG_SPL_NAND_DRIVERS
-               SPL uses normal NAND drivers, not minimal drivers.
-
                CONFIG_SPL_NAND_IDENT
                SPL uses the chip ID list to identify the NAND flash.
                Requires CONFIG_SPL_NAND_BASE.
 
-               CONFIG_SPL_NAND_ECC
-               Include standard software ECC in the SPL
-
-               CONFIG_SPL_NAND_SIMPLE
-               Support for NAND boot using simple NAND drivers that
-               expose the cmd_ctrl() interface.
-
                CONFIG_SPL_UBI
                Support for a lightweight UBI (fastmap) scanner and
                loader
@@ -3470,6 +3402,11 @@ List of environment variables (most likely not complete):
                  downloads succeed with high packet loss rates, or with
                  unreliable TFTP servers or client hardware.
 
+  tftpwindowsize       - if this is set, the value is used for TFTP's
+                 window size as described by RFC 7440.
+                 This means the count of blocks we can receive before
+                 sending ack to server.
+
   vlan         - When set to a value < 4095 the traffic over
                  Ethernet is encapsulated/received over 802.1q
                  VLAN tagged frames.