such as ARM architectural timer initialization.
- Linux Kernel Interface:
- CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
-
- When transferring memsize parameter to Linux, some versions
- expect it to be in bytes, others in MB.
- Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
-
CONFIG_OF_LIBFDT
New kernel versions are expecting firmware settings to be
Support for generic parallel port TPM devices. Only one device
per system is supported at this time.
- CONFIG_TPM_TIS_BASE_ADDRESS
- Base address where the generic TPM device is mapped
- to. Contemporary x86 systems usually map it at
- 0xfed40000.
-
CONFIG_TPM
Define this to enable the TPM support library which provides
functional interfaces to some TPM commands.
Some PHY like Intel LXT971A need extra delay after
command issued before MII status register can be read
-- IP address:
- CONFIG_IPADDR
-
- Define a default value for the IP address to use for
- the default Ethernet interface, in case this is not
- determined through e.g. bootp.
- (Environment variable "ipaddr")
-
-- Server IP address:
- CONFIG_SERVERIP
-
- Defines a default value for the IP address of a TFTP
- server to contact when using the "tftboot" command.
- (Environment variable "serverip")
-
-- Gateway IP address:
- CONFIG_GATEWAYIP
-
- Defines a default value for the IP address of the
- default router where packets to other networks are
- sent to.
- (Environment variable "gatewayip")
-
-- Subnet mask:
- CONFIG_NETMASK
-
- Defines a default value for the subnet mask (or
- routing prefix) which is used to determine if an IP
- address belongs to the local subnet or needs to be
- forwarded through a router.
- (Environment variable "netmask")
-
- BOOTP Recovery Mode:
CONFIG_BOOTP_RANDOM_DELAY
CFG_SYS_I2C_NOPROBES
This option specifies a list of I2C devices that will be skipped
- when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
- is set, specify a list of bus-device pairs. Otherwise, specify
- a 1D array of device addresses
+ when the 'i2c probe' command is issued.
e.g.
- #undef CONFIG_I2C_MULTI_BUS
#define CFG_SYS_I2C_NOPROBES {0x50,0x68}
will skip addresses 0x50 and 0x68 on a board with one I2C bus
- #define CONFIG_I2C_MULTI_BUS
- #define CFG_SYS_I2C_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
-
- will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
-
CFG_SYS_RTC_BUS_NUM
If defined, then this indicates the I2C bus number for the RTC.
- CONFIG_SYS_FLASH_USE_BUFFER_WRITE
Use buffered writes to flash.
-- CONFIG_FLASH_SPANSION_S29WS_N
- s29ws-n MirrorBit flash has non-standard addresses for buffered
- write commands.
-
-- CONFIG_FLASH_SHOW_PROGRESS
- If defined (must be an integer), print out countdown
- digits and dots. Recommended value: 45 (9..1) for 80
- column displays, 15 (3..1) for 40 column displays.
-
-- CONFIG_FLASH_VERIFY
- If defined, the content of the flash (destination) is compared
- against the source after the write operation. An error message
- will be printed when the contents are not identical.
- Please note that this option is useless in nearly all cases,
- since such flash programming errors usually are detected earlier
- while unprotecting/erasing/programming. Please only enable
- this option if you really know what you are doing.
-
- CONFIG_ENV_FLAGS_LIST_DEFAULT
- CONFIG_ENV_FLAGS_LIST_STATIC
Enable validation of the values given to environment variables when