Define this option if you want to enable the
ICache only when Code runs from RAM.
+- 85xx CPU Options:
+ CONFIG_SYS_FSL_TBCLK_DIV
+
+ Defines the core time base clock divider ratio compared to the
+ system clock. On most PQ3 devices this is 8, on newer QorIQ
+ devices it can be 16 or 32. The ratio varies from SoC to Soc.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_GO * the 'go' command (exec code)
+ CONFIG_CMD_GREPENV * search environment
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
+ CONFIG_SYS_RV3029_TCR - enable trickle charger on
+ RV3029 RTC.
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
CONFIG_VIDEO_LOGO
CONFIG_VIDEO_BMP_LOGO
- The DIU driver will look for the 'monitor' environment variable,
- and if defined, enable the DIU as a console during boot. This
- variable should be set to one of these values:
-
- '0' Output video to the DVI connector
- '1' Output video to the LVDS connector
- '2' Output video to the Dual-Link LVDS connector
+ The DIU driver will look for the 'video-mode' environment
+ variable, and if defined, enable the DIU as a console during
+ boot. See the documentation file README.video for a
+ description of this variable.
- Keyboard Support:
CONFIG_KEYBOARD
thus overwriting the architecutre dependent default
settings.
+- Frame Buffer Address:
+ CONFIG_FB_ADDR
+
+ Define CONFIG_FB_ADDR if you want to use specific address for
+ frame buffer.
+ Then system will reserve the frame buffer address to defined address
+ instead of lcd_setmem (this function grab the memory for frame buffer
+ by panel's size).
+
+ Please see board_init_f function.
+
+ If you want this config option then,
+ please define it at your board config file
+
Legacy uImage format:
Arg Where When
used) must be put below this limit, unless "bootm_low"
enviroment variable is defined and non-zero. In such case
all data for the Linux kernel must be between "bootm_low"
- and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+ and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
+ variable "bootm_mapsize" will override the value of
+ CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
+ then the value in "bootm_size" will be used instead.
- CONFIG_SYS_BOOT_RAMDISK_HIGH:
Enable initrd_high functionality. If defined then the
source code. It is used to make hardware dependant
initializations.
+- CONFIG_IDE_AHB:
+ Most IDE controllers were designed to be connected with PCI
+ interface. Only few of them were designed for AHB interface.
+ When software is doing ATA command and data transfer to
+ IDE devices through IDE-AHB controller, some additional
+ registers accessing to these kind of IDE-AHB controller
+ is requierd.
+
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
doing! (11-4) [MPC8xx/82xx systems only]
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_USE_ARCH_MEMCPY
+ CONFIG_USE_ARCH_MEMSET
+ If these options are used a optimized version of memcpy/memset will
+ be used if available. These functions may be faster under some
+ conditions but may increase the binary size.
+
Building the Software:
======================
for use by the bootm command. See also "bootm_size"
environment variable. Address defined by "bootm_low" is
also the base of the initial memory mapping for the Linux
- kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
+ kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
+ bootm_mapsize.
+
+ bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
+ This variable is given as a hexadecimal number and it
+ defines the size of the memory region starting at base
+ address bootm_low that is accessible by the Linux kernel
+ during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
+ as the default value if it is defined, and bootm_size is
+ used otherwise.
bootm_size - Memory range available for image processing in the bootm
command can be restricted. This variable is given as