/at91 Files specific to Atmel AT91RM9200 CPU
/imx Files specific to Freescale MC9328 i.MX CPUs
/s3c24x0 Files specific to Samsung S3C24X0 CPUs
- /arm925t Files specific to ARM 925 CPUs
/arm926ejs Files specific to ARM 926 CPUs
/arm1136 Files specific to ARM 1136 CPUs
/ixp Files specific to Intel XScale IXP CPUs
the "silent" environment variable. See
doc/README.silent for more information.
+ CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
+ is 0x00.
+ CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
+ is 0xa0.
+
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CONFIG_CMD_ELF * bootelf, bootvx
CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
CONFIG_CMD_ENV_FLAGS * display details about env flags
+ CONFIG_CMD_ENV_EXISTS * check existence of env variable
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_EXT2 * ext2 command support
CONFIG_CMD_EXT4 * ext4 command support
- Regular expression support:
CONFIG_REGEX
- If this variable is defined, U-Boot is linked against
- the SLRE (Super Light Regular Expression) library,
- which adds regex support to some commands, as for
- example "env grep" and "setexpr".
+ If this variable is defined, U-Boot is linked against
+ the SLRE (Super Light Regular Expression) library,
+ which adds regex support to some commands, as for
+ example "env grep" and "setexpr".
- Device tree:
CONFIG_OF_CONTROL
- GPIO Support:
CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
- CONFIG_PCA953X_INFO - enable pca953x info command
The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
chip-ngpio pairs that tell the PCA953X driver the number of
devices.
CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
- The environment variable 'scsidevs' is set to the number of
- SCSI devices found during the last scan.
+ The environment variable 'scsidevs' is set to the number of
+ SCSI devices found during the last scan.
- NETWORK Support (PCI):
CONFIG_E1000
for your device
- CONFIG_USBD_PRODUCTID 0xFFFF
+ Some USB device drivers may need to check USB cable attachment.
+ In this case you can enable following config in BoardName.h:
+ CONFIG_USB_CABLE_CHECK
+ This enables function definition:
+ - usb_cable_connected() in include/usb.h
+ Implementation of this function is board-specific.
+
- ULPI Layer Support:
The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
the generic ULPI layer. The generic layer accesses the ULPI PHY
kernel). Defining CONFIG_STATUS_LED enables this
feature in U-Boot.
+ Additional options:
+
+ CONFIG_GPIO_LED
+ The status LED can be connected to a GPIO pin.
+ In such cases, the gpio_led driver can be used as a
+ status LED backend implementation. Define CONFIG_GPIO_LED
+ to include the gpio_led driver in the U-Boot binary.
+
+ CONFIG_GPIO_LED_INVERTED_TABLE
+ Some GPIO connected LEDs may have inverted polarity in which
+ case the GPIO high value corresponds to LED off state and
+ GPIO low value corresponds to LED on state.
+ In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
+ with a list of GPIO LEDs that have inverted polarity.
+
- CAN Support: CONFIG_CAN_DRIVER
Defining CONFIG_CAN_DRIVER enables CAN driver support
offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
bus.
- - If your board supports a second fsl i2c bus, define
+ - If your board supports a second fsl i2c bus, define
CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
CONFIG_SYS_FSL_I2C2_SPEED for the speed and
CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
second bus.
- drivers/i2c/tegra_i2c.c:
- - activate this driver with CONFIG_SYS_I2C_TEGRA
- - This driver adds 4 i2c buses with a fix speed from
- 100000 and the slave addr 0!
+ - activate this driver with CONFIG_SYS_I2C_TEGRA
+ - This driver adds 4 i2c buses with a fix speed from
+ 100000 and the slave addr 0!
- drivers/i2c/ppc4xx_i2c.c
- activate this driver with CONFIG_SYS_I2C_PPC4XX
- CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0
- CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1
+ - drivers/i2c/i2c_mxc.c
+ - activate this driver with CONFIG_SYS_I2C_MXC
+ - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
+ - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
+ - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
+ - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
+ - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
+ - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
+ If thoses defines are not set, default value is 100000
+ for speed, and 0 for slave.
+
+ - drivers/i2c/rcar_i2c.c:
+ - activate this driver with CONFIG_SYS_I2C_RCAR
+ - This driver adds 4 i2c buses
+
+ - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
+ - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
+ - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
+ - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
+ - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
+ - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
+ - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
+ - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
+ - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
+
+ - drivers/i2c/sh_i2c.c:
+ - activate this driver with CONFIG_SYS_I2C_SH
+ - This driver adds from 2 to 5 i2c buses
+
+ - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
+ - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
+ - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
+ - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
+ - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
+ - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
+ - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
+ - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
+ - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
+ - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
+ - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
+ - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
+ - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses
+
+ - drivers/i2c/omap24xx_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_OMAP24XX
+ - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
+ - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
+ - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
+ - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
+ - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
+ - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
+ - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
+ - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
+ - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
+ - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
+
+ - drivers/i2c/zynq_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_ZYNQ
+ - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
+ - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
CONFIG_TPL_PAD_TO
Image offset to which the TPL should be padded before appending
the TPL payload. By default, this is defined as
- CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
- CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
- payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
+ CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
+ CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
+ payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
Modem Support:
--------------