boards with QUICC Engines require OF_QE to set UCC MAC
addresses
- CONFIG_OF_BOARD_SETUP
-
- Board code has addition modification that it wants to make
- to the flat device tree before handing it off to the kernel
-
CONFIG_OF_SYSTEM_SETUP
Other code has addition modification that it wants to make
Note: If a "bootargs" environment is defined, it will override
the defaults discussed just above.
-- Cache Configuration:
- CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
-
- Cache Configuration for ARM:
CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
controller
example "env grep" and "setexpr".
- Watchdog:
- CONFIG_WATCHDOG
- If this variable is defined, it enables watchdog
- support for the SoC. There must be support in the SoC
- specific code for a watchdog. For the 8xx
- CPUs, the SIU Watchdog feature is enabled in the SYPCR
- register. When supported for a specific SoC is
- available, then no further board specific code should
- be needed to use it.
-
- CONFIG_HW_WATCHDOG
- When using a watchdog circuitry external to the used
- SoC, then define this variable and provide board
- specific code for the "hw_watchdog_reset" function.
-
CONFIG_SYS_WATCHDOG_FREQ
Some platforms automatically call WATCHDOG_RESET()
from the timer interrupt handler every
sending again an USB request to the device.
- Journaling Flash filesystem support:
- CONFIG_JFFS2_NAND
- Define these for a default partition on a NAND device
-
CONFIG_SYS_JFFS2_FIRST_SECTOR,
CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
Define these for a default partition on a NOR device
CONFIG_CFB_CONSOLE
CONFIG_VIDEO_SW_CURSOR
CONFIG_VGA_AS_SINGLE_DEVICE
- CONFIG_VIDEO_LOGO
CONFIG_VIDEO_BMP_LOGO
The DIU driver will look for the 'video-mode' environment
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
- CONFIG_SOFT_SPI
-
- Enables a software (bit-bang) SPI driver rather than
- using hardware support. This is a general purpose
- driver that only requires three general I/O port pins
- (two outputs, one input) to function. If this is
- defined, the board configuration must define several
- SPI configuration items (port pins to use, etc). For
- an example, see include/configs/sacsng.h.
-
CONFIG_SYS_SPI_MXC_WAIT
Timeout for waiting until spi transfer completed.
default: (CONFIG_SYS_HZ/100) /* 10 ms */
Time to wait after FPGA configuration. The default is
200 ms.
-- Configuration Management:
-
- CONFIG_IDENT_STRING
-
- If defined, this string will be added to the U-Boot
- version information (U_BOOT_VERSION)
-
- Vendor Parameter Protection:
U-Boot considers the values of the environment
CONFIG_SPL_INIT_MINIMAL
Arch init code should be built for a very small image
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
- Partition on the MMC to load U-Boot from when the MMC is being
- used in raw mode
-
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
Sector to load kernel uImage from when MMC is being
used in raw mode (for Falcon mode)
* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
- Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
- INTEGRITY).
+ Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, INTEGRITY).
* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
Currently supported: ARM, Intel x86, MIPS, NDS32, Nios II, PowerPC).