/blackfin Files generic to Analog Devices Blackfin architecture
/cpu CPU specific files
/lib Architecture specific library files
- /i386 Files generic to i386 architecture
+ /x86 Files generic to x86 architecture
/cpu CPU specific files
/lib Architecture specific library files
/m68k Files generic to m68k architecture
CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
CONFIG_SYS_8272ADS - MPC8272ADS
+- Marvell Family Member
+ CONFIG_SYS_MVFS - define it if you want to enable
+ multiple fs option at one time
+ for marvell soc family
+
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
+ CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
- CONFIG_CMD_SHA1 print sha1 memory digest
+ CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
+ CONFIG_SH_ETHER
+ Support for Renesas on-chip Ethernet controller
+
+ CONFIG_SH_ETHER_USE_PORT
+ Define the number of ports to be used
+
+ CONFIG_SH_ETHER_PHY_ADDR
+ Define the ETH PHY's address
+
+ CONFIG_SH_ETHER_CACHE_WRITEBACK
+ If this option is set, the driver enables cache flush.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
or CONFIG_VIDEO_SED13806_16BPP
+ CONFIG_FSL_DIU_FB
+ Enable the Freescale DIU video driver. Reference boards for
+ SOCs that have a DIU should define this macro to enable DIU
+ support, and should also define these other macros:
+
+ CONFIG_SYS_DIU_ADDR
+ CONFIG_VIDEO
+ CONFIG_CMD_BMP
+ CONFIG_CFB_CONSOLE
+ CONFIG_VIDEO_SW_CURSOR
+ CONFIG_VGA_AS_SINGLE_DEVICE
+ CONFIG_VIDEO_LOGO
+ CONFIG_VIDEO_BMP_LOGO
+
+ The DIU driver will look for the 'monitor' environment variable,
+ and if defined, enable the DIU as a console during boot. This
+ variable should be set to one of these values:
+
+ '0' Output video to the DVI connector
+ '1' Output video to the LVDS connector
+ '2' Output video to the Dual-Link LVDS connector
+
- Keyboard Support:
CONFIG_KEYBOARD
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
+ CONFIG_SH_SPI
+
+ Enables the driver for SPI controller on SuperH. Currently
+ only SH7757 is supported.
+
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
+- Standalone program support:
+ CONFIG_STANDALONE_LOAD_ADDR
+
+ This option allows to define board specific values
+ for the address where standalone program gets loaded,
+ thus overwriting the architecutre dependent default
+ settings.
+
Legacy uImage format:
Arg Where When