board: tec-ng: Do not make directories in a board Makefile

[platform/kernel/u-boot.git] / README

diff --git a/README b/README
index 1130b4f..176de61 100644 (file)
--- a/README
+++ b/README
@@ -423,6 +423,11 @@ The following options need to be configured:
                CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
                This value denotes start offset of DSP CCSR space.
 
+               CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+               Single Source Clock is clocking mode present in some of FSL SoC's.
+               In this mode, a single differential clock is used to supply
+               clocks to the sysclock, ddrclock and usbclock.
+
 - Generic CPU options:
                CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
@@ -467,6 +472,15 @@ The following options need to be configured:
                Board config to use DDR3. It can be enabled for SoCs with
                Freescale DDR3 controllers.
 
+               CONFIG_SYS_FSL_PBL_PBI
+               It enables addition of RCW (Power on reset configuration) in built image.
+               Please refer doc/README.pblimage for more details
+
+               CONFIG_SYS_FSL_PBL_RCW
+               It adds PBI(pre-boot instructions) commands in u-boot build image.
+               PBI commands can be used to configure SoC before it starts the execution.
+               Please refer doc/README.pblimage for more details
+
 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
@@ -2141,6 +2155,12 @@ CBFS (Coreboot Filesystem) support
                  - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
                  - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
 
+               - drivers/i2c/s3c24x0_i2c.c:
+                 - activate this driver with CONFIG_SYS_I2C_S3C24X0
+                 - This driver adds i2c buses (11 for Exynos5250, Exynos5420
+                   9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
+                   with a fix speed from 100000 and the slave addr 0!
+
                additional defines:
 
                CONFIG_SYS_NUM_I2C_BUSES
@@ -2745,6 +2765,12 @@ CBFS (Coreboot Filesystem) support
                Define this option to use the Bank addr/Extended addr
                support on SPI flashes which has size > 16Mbytes.
 
+               CONFIG_SF_DUAL_FLASH            Dual flash memories
+
+               Define this option to use dual flash support where two flash
+               memories can be connected with a given cs line.
+               currently Xilinx Zynq qspi support these type of connections.
+
 - SystemACE Support:
                CONFIG_SYSTEMACE
 
@@ -3261,6 +3287,9 @@ FIT uImage format:
                Defines the size and behavior of the NAND that SPL uses
                to read U-Boot
 
+               CONFIG_SPL_NAND_BOOT
+               Add support NAND boot
+
                CONFIG_SYS_NAND_U_BOOT_OFFS
                Location in NAND to read U-Boot from
 
@@ -5246,6 +5275,15 @@ when your kernel is intended to use an initial ramdisk:
        Load Address: 0x00000000
        Entry Point:  0x00000000
 
+The "dumpimage" is a tool to disassemble images built by mkimage. Its "-i"
+option performs the converse operation of the mkimage's second form (the "-d"
+option). Given an image built by mkimage, the dumpimage extracts a "data file"
+from the image:
+
+       tools/dumpimage -i image -p position data_file
+         -i ==> extract from the 'image' a specific 'data_file', \
+          indexed by 'position'
+
 
 Installing a Linux Image:
 -------------------------