CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
This value denotes start offset of DSP CCSR space.
+ CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+ Single Source Clock is clocking mode present in some of FSL SoC's.
+ In this mode, a single differential clock is used to supply
+ clocks to the sysclock, ddrclock and usbclock.
+
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Board config to use DDR3. It can be enabled for SoCs with
Freescale DDR3 controllers.
+ CONFIG_SYS_FSL_PBL_PBI
+ It enables addition of RCW (Power on reset configuration) in built image.
+ Please refer doc/README.pblimage for more details
+
+ CONFIG_SYS_FSL_PBL_RCW
+ It adds PBI(pre-boot instructions) commands in u-boot build image.
+ PBI commands can be used to configure SoC before it starts the execution.
+ Please refer doc/README.pblimage for more details
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
as a convenience, when switching between booting from
RAM and NFS.
+- Bootcount:
+ CONFIG_BOOTCOUNT_LIMIT
+ Implements a mechanism for detecting a repeating reboot
+ cycle, see:
+ http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
+
+ CONFIG_BOOTCOUNT_ENV
+ If no softreset save registers are found on the hardware
+ "bootcount" is stored in the environment. To prevent a
+ saveenv on all reboots, the environment variable
+ "upgrade_available" is used. If "upgrade_available" is
+ 0, "bootcount" is always 0, if "upgrade_available" is
+ 1 "bootcount" is incremented in the environment.
+ So the Userspace Applikation must set the "upgrade_available"
+ and "bootcount" variable to 0, if a boot was successfully.
+
- Pre-Boot Commands:
CONFIG_PREBOOT
kernel). Defining CONFIG_STATUS_LED enables this
feature in U-Boot.
+ Additional options:
+
+ CONFIG_GPIO_LED
+ The status LED can be connected to a GPIO pin.
+ In such cases, the gpio_led driver can be used as a
+ status LED backend implementation. Define CONFIG_GPIO_LED
+ to include the gpio_led driver in the U-Boot binary.
+
+ CONFIG_GPIO_LED_INVERTED_TABLE
+ Some GPIO connected LEDs may have inverted polarity in which
+ case the GPIO high value corresponds to LED off state and
+ GPIO low value corresponds to LED on state.
+ In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
+ with a list of GPIO LEDs that have inverted polarity.
+
- CAN Support: CONFIG_CAN_DRIVER
Defining CONFIG_CAN_DRIVER enables CAN driver support
- set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
- set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
+ - drivers/i2c/s3c24x0_i2c.c:
+ - activate this driver with CONFIG_SYS_I2C_S3C24X0
+ - This driver adds i2c buses (11 for Exynos5250, Exynos5420
+ 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
+ with a fix speed from 100000 and the slave addr 0!
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
Define this option to use the Bank addr/Extended addr
support on SPI flashes which has size > 16Mbytes.
+ CONFIG_SF_DUAL_FLASH Dual flash memories
+
+ Define this option to use dual flash support where two flash
+ memories can be connected with a given cs line.
+ currently Xilinx Zynq qspi support these type of connections.
+
- SystemACE Support:
CONFIG_SYSTEMACE
Defines the size and behavior of the NAND that SPL uses
to read U-Boot
+ CONFIG_SPL_NAND_BOOT
+ Add support NAND boot
+
CONFIG_SYS_NAND_U_BOOT_OFFS
Location in NAND to read U-Boot from
NOTE : currently only supported on AM335x platforms.
+- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
+ Enables the RTC32K OSC on AM33xx based plattforms
+
Freescale QE/FMAN Firmware Support:
-----------------------------------
Load Address: 0x00000000
Entry Point: 0x00000000
+The "dumpimage" is a tool to disassemble images built by mkimage. Its "-i"
+option performs the converse operation of the mkimage's second form (the "-d"
+option). Given an image built by mkimage, the dumpimage extracts a "data file"
+from the image:
+
+ tools/dumpimage -i image -p position data_file
+ -i ==> extract from the 'image' a specific 'data_file', \
+ indexed by 'position'
+
Installing a Linux Image:
-------------------------