CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
This value denotes start offset of DSP CCSR space.
- CONFIG_SYS_FSL_DDR_EMU
- Specify emulator support for DDR. Some DDR features such as
- deskew training are not available.
+ CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+ Single Source Clock is clocking mode present in some of FSL SoC's.
+ In this mode, a single differential clock is used to supply
+ clocks to the sysclock, ddrclock and usbclock.
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Defines the endianess of the CPU. Implementation of those
values is arch specific.
+ CONFIG_SYS_FSL_DDR
+ Freescale DDR driver in use. This type of DDR controller is
+ found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
+ SoCs.
+
+ CONFIG_SYS_FSL_DDR_ADDR
+ Freescale DDR memory-mapped register base.
+
+ CONFIG_SYS_FSL_DDR_EMU
+ Specify emulator support for DDR. Some DDR features such as
+ deskew training are not available.
+
+ CONFIG_SYS_FSL_DDRC_GEN1
+ Freescale DDR1 controller.
+
+ CONFIG_SYS_FSL_DDRC_GEN2
+ Freescale DDR2 controller.
+
+ CONFIG_SYS_FSL_DDRC_GEN3
+ Freescale DDR3 controller.
+
+ CONFIG_SYS_FSL_DDRC_ARM_GEN3
+ Freescale DDR3 controller for ARM-based SoCs.
+
+ CONFIG_SYS_FSL_DDR1
+ Board config to use DDR1. It can be enabled for SoCs with
+ Freescale DDR1 or DDR2 controllers, depending on the board
+ implemetation.
+
+ CONFIG_SYS_FSL_DDR2
+ Board config to use DDR2. It can be eanbeld for SoCs with
+ Freescale DDR2 or DDR3 controllers, depending on the board
+ implementation.
+
+ CONFIG_SYS_FSL_DDR3
+ Board config to use DDR3. It can be enabled for SoCs with
+ Freescale DDR3 controllers.
+
+ CONFIG_SYS_FSL_PBL_PBI
+ It enables addition of RCW (Power on reset configuration) in built image.
+ Please refer doc/README.pblimage for more details
+
+ CONFIG_SYS_FSL_PBL_RCW
+ It adds PBI(pre-boot instructions) commands in u-boot build image.
+ PBI commands can be used to configure SoC before it starts the execution.
+ Please refer doc/README.pblimage for more details
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
kernel). Defining CONFIG_STATUS_LED enables this
feature in U-Boot.
+ Additional options:
+
+ CONFIG_GPIO_LED
+ The status LED can be connected to a GPIO pin.
+ In such cases, the gpio_led driver can be used as a
+ status LED backend implementation. Define CONFIG_GPIO_LED
+ to include the gpio_led driver in the U-Boot binary.
+
+ CONFIG_GPIO_LED_INVERTED_TABLE
+ Some GPIO connected LEDs may have inverted polarity in which
+ case the GPIO high value corresponds to LED off state and
+ GPIO low value corresponds to LED on state.
+ In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
+ with a list of GPIO LEDs that have inverted polarity.
+
- CAN Support: CONFIG_CAN_DRIVER
Defining CONFIG_CAN_DRIVER enables CAN driver support
- CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
- CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
+ - drivers/i2c/sh_i2c.c:
+ - activate this driver with CONFIG_SYS_I2C_SH
+ - This driver adds from 2 to 5 i2c buses
+
+ - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
+ - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
+ - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
+ - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
+ - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
+ - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
+ - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
+ - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
+ - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
+ - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
+ - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
+ - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
+ - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses
+
+ - drivers/i2c/omap24xx_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_OMAP24XX
+ - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
+ - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
+ - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
+ - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
+ - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
+ - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
+ - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
+ - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
+ - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
+ - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
+
+ - drivers/i2c/zynq_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_ZYNQ
+ - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
+ - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
+
+ - drivers/i2c/s3c24x0_i2c.c:
+ - activate this driver with CONFIG_SYS_I2C_S3C24X0
+ - This driver adds i2c buses (11 for Exynos5250, Exynos5420
+ 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
+ with a fix speed from 100000 and the slave addr 0!
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
Define this option to use the Bank addr/Extended addr
support on SPI flashes which has size > 16Mbytes.
+ CONFIG_SF_DUAL_FLASH Dual flash memories
+
+ Define this option to use dual flash support where two flash
+ memories can be connected with a given cs line.
+ currently Xilinx Zynq qspi support these type of connections.
+
- SystemACE Support:
CONFIG_SYSTEMACE
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
Set for the SPL on PPC mpc8xxx targets, support for
- arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+ drivers/ddr/fsl/libddr.o in SPL binary.
CONFIG_SPL_COMMON_INIT_DDR
Set for common ddr init with serial presence detect in
Defines the size and behavior of the NAND that SPL uses
to read U-Boot
+ CONFIG_SPL_NAND_BOOT
+ Add support NAND boot
+
CONFIG_SYS_NAND_U_BOOT_OFFS
Location in NAND to read U-Boot from
NOTE : currently only supported on AM335x platforms.
+- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
+ Enables the RTC32K OSC on AM33xx based plattforms
+
Freescale QE/FMAN Firmware Support:
-----------------------------------
Load Address: 0x00000000
Entry Point: 0x00000000
+The "dumpimage" is a tool to disassemble images built by mkimage. Its "-i"
+option performs the converse operation of the mkimage's second form (the "-d"
+option). Given an image built by mkimage, the dumpimage extracts a "data file"
+from the image:
+
+ tools/dumpimage -i image -p position data_file
+ -i ==> extract from the 'image' a specific 'data_file', \
+ indexed by 'position'
+
Installing a Linux Image:
-------------------------