/arch Architecture specific files
/arc Files generic to ARC architecture
/arm Files generic to ARM architecture
- /avr32 Files generic to AVR32 architecture
/m68k Files generic to m68k architecture
/microblaze Files generic to microblaze architecture
/mips Files generic to MIPS architecture
- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
-- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
- Define exactly one, e.g. CONFIG_ATSTK1002
-
- Marvell Family Member
CONFIG_SYS_MVFS - define it if you want to enable
multiple fs option at one time
for marvell soc family
-- 8xx CPU Options: (if using an MPC8xx CPU)
- CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
- get_gclk_freq() cannot work
- e.g. if there is no 32KHz
- reference PIT/RTC clock
- CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
- or XTAL/EXTAL)
-
-- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
- CONFIG_SYS_8xx_CPUCLK_MIN
- CONFIG_SYS_8xx_CPUCLK_MAX
- CONFIG_8xx_CPUCLK_DEFAULT
- See doc/README.MPC866
-
- CONFIG_SYS_MEASURE_CPUCLK
-
- Define this to measure the actual CPU clock instead
- of relying on the correctness of the configured
- values. Mostly useful for board bringup to make sure
- the PLL is locked at the intended frequency. Note
- that this requires a (stable) reference clock (32 kHz
- RTC clock or CONFIG_SYS_8XX_XIN)
-
- CONFIG_SYS_DELAYED_ICACHE
-
- Define this option if you want to enable the
- ICache only when Code runs from RAM.
-
- 85xx CPU Options:
CONFIG_SYS_PPC64
* Adds the "fdt" command
* The bootm command automatically updates the fdt
- OF_CPU - The proper name of the cpus node (only required for
- MPC512X and MPC5xxx based boards).
- OF_SOC - The proper name of the soc node (only required for
- MPC512X and MPC5xxx based boards).
OF_TBCLK - The timebase frequency.
OF_STDOUT_PATH - The path to the console device
Define this variable to enable hw flow control in serial driver.
Current user of this option is drivers/serial/nsl16550.c driver
-- Console Interface:
- Depending on board, define exactly one serial port
- (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
- CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
- console by defining CONFIG_8xx_CONS_NONE
-
- Note: if CONFIG_8xx_CONS_NONE is defined, the serial
- port routines must be defined elsewhere
- (i.e. serial_init(), serial_getc(), ...)
-
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CONFIG_SYS_BAUDRATE_TABLE, see below.
- CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
-
-- Console Rx buffer length
- With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
- the maximum receive buffer length for the SMC.
- This option is actual only for 82xx and 8xx possible.
- If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
- must be defined, to setup the maximum idle timeout for
- the SMC.
- Autoboot Command:
CONFIG_BOOTCOMMAND
CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
- CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
- CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
- CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
- CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
- CONFIG_CMD_EEPROM * EEPROM read/write support
- CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
CONFIG_CMD_ELF * bootelf, bootvx
- CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
- CONFIG_CMD_ENV_FLAGS * display details about env flags
CONFIG_CMD_ENV_EXISTS * check existence of env variable
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_EXT2 * ext2 command support
that work for multiple fs types
CONFIG_CMD_FS_UUID * Look up a filesystem UUID
CONFIG_CMD_SAVEENV saveenv
- CONFIG_CMD_FDC * Floppy Disk Support
- CONFIG_CMD_FAT * FAT command support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
- CONFIG_CMD_FUSE * Device fuse support
- CONFIG_CMD_GETTIME * Get time since boot
CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_GREPENV * search environment
- CONFIG_CMD_HASH * calculate hash / digest
CONFIG_CMD_I2C * I2C serial bus support
- CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all images found in NOR flash
CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
- CONFIG_CMD_IMMAP * IMMR dump support
- CONFIG_CMD_IOTRACE * I/O tracing for debugging
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
- CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
- CONFIG_CMD_JFFS2 * JFFS2 Support
- CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
(169.254.*.*)
CONFIG_CMD_MISC Misc functions like sleep etc
CONFIG_CMD_MMC * MMC memory mapped support
CONFIG_CMD_MII * MII utility commands
- CONFIG_CMD_MTDPARTS * MTD partition support
CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
CONFIG_CMD_NFS NFS support
CONFIG_CMD_RUN run command in env variable
CONFIG_CMD_SANDBOX * sb command to access sandbox features
CONFIG_CMD_SAVES * save S record dump
- CONFIG_SCSI * SCSI Support
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
- CONFIG_CMD_SETGETDCR Support for DCR Register access
- (4xx only)
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
- CONFIG_CMD_SHA1SUM * print sha1 memory digest
- (requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
Note: Don't enable the "icache" and "dcache" commands
(configuration option CONFIG_CMD_CACHE) unless you know
what you (and your U-Boot users) are doing. Data
- cache cannot be enabled on systems like the 8xx or
- 8260 (where accesses to the IMMR region must be
+ cache cannot be enabled on systems like the
+ 8xx (where accesses to the IMMR region must be
uncached), and it cannot be disabled on all other
systems where we (mis-) use the data cache to hold an
initial stack and some data.
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
support for the SoC. There must be support in the SoC
- specific code for a watchdog. For the 8xx and 8260
+ specific code for a watchdog. For the 8xx
CPUs, the SIU Watchdog feature is enabled in the SYPCR
register. When supported for a specific SoC is
available, then no further board specific code should
has to be selected, too. Define exactly one of the
following options:
- CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
- CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
+ CONFIG_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
CONFIG_SYS_RV3029_TCR - enable trickle charger on
RV3029 RTC.
- Partition Labels (disklabels) Supported:
Zero or more of the following:
CONFIG_MAC_PARTITION Apple's MacOS partition table.
- CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
- Intel architecture, USB sticks, etc.
CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
bootloader. Note 2TB partition limit; see
disk/part_efi.c
CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
- If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
+ If IDE or SCSI support is enabled (CONFIG_IDE or
CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
Default is 32bit.
- SCSI Support:
- At the moment only there is only support for the
- SYM53C8XX SCSI controller; define
- CONFIG_SCSI_SYM53C8XX to enable it.
-
CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
maximum numbers of LUNs, SCSI ID's and target
devices.
- CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
The environment variable 'scsidevs' is set to the number of
SCSI devices found during the last scan.
- USB Support:
At the moment only the UHCI host controller is
- supported (PIP405, MIP405, MPC5200); define
+ supported (PIP405, MIP405); define
CONFIG_USB_UHCI to enable it.
define CONFIG_USB_KEYBOARD to enable the USB Keyboard
and define CONFIG_USB_STORAGE to enable the USB
Note:
Supported are USB Keyboards and USB Floppy drives
(TEAC FD-05PUB).
- MPC5200 USB requires additional defines:
- CONFIG_USB_CLOCK
- for 528 MHz Clock: 0x0001bbbb
- CONFIG_PSC3_USB
- for USB on PSC3
- CONFIG_USB_CONFIG
- for differential drivers: 0x00001000
- for single ended drivers: 0x00005000
- for differential drivers on PSC3: 0x00000100
- for single ended drivers on PSC3: 0x00004100
- CONFIG_SYS_USB_EVENT_POLL
- May be defined to allow interrupt polling
- instead of using asynchronous interrupts
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
Define this if you want stdin, stdout &/or stderr to
be set to usbtty.
- mpc8xx:
- CONFIG_SYS_USB_EXTC_CLK 0xBLAH
- Derive USB clock from external clock "blah"
- - CONFIG_SYS_USB_EXTC_CLK 0x02
-
If you have a USB-IF assigned VendorID then you may wish to
define your own vendor specific values either in BoardName.h
or directly in usbd_vendor_info.h. If you don't define
CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
Define these for a default partition on a NOR device
-- FAT(File Allocation Table) filesystem write function support:
- CONFIG_FAT_WRITE
-
- Define this to enable support for saving memory data as a
- file in FAT formatted partition.
-
- This will also enable the command "fatwrite" enabling the
- user to write files to FAT.
-
-- FAT(File Allocation Table) filesystem cluster size:
- CONFIG_FS_FAT_MAX_CLUSTSIZE
-
- Define the max cluster size for fat operations else
- a default value of 65536 will be defined.
-
- Keyboard Support:
See Kconfig help for available keyboard drivers.
the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
be at least 4MB.
- CONFIG_LZMA
-
- If this option is set, support for lzma compressed
- images is included.
-
- Note: The LZMA algorithm adds between 2 and 4KB of code and it
- requires an amount of dynamic memory that is given by the
- formula:
-
- (1846 + 768 << (lc + lp)) * sizeof(uint16)
-
- Where lc and lp stand for, respectively, Literal context bits
- and Literal pos bits.
-
- This value is upper-bounded by 14MB in the worst case. Anyway,
- for a ~4MB large kernel image, we have lc=3 and lp=0 for a
- total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
- a very small buffer.
-
- Use the lzmainfo tool to determinate the lc and lp values and
- then calculate the amount of needed dynamic memory (ensuring
- the appropriate CONFIG_SYS_MALLOC_LEN value).
-
- CONFIG_LZO
-
- If this option is set, support for LZO compressed images
- is included.
-
- MII/PHY support:
CONFIG_PHY_ADDR
In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
with a list of GPIO LEDs that have inverted polarity.
-- CAN Support: CONFIG_CAN_DRIVER
-
- Defining CONFIG_CAN_DRIVER enables CAN driver support
- on those systems that support this (optional)
- feature, like the TQM8xxL modules.
-
- I2C Support: CONFIG_SYS_I2C
This enable the NEW i2c subsystem, and will allow you to use
eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
- I2C_PORT
-
- (Only for MPC8260 CPU). The I/O port to use (the code
- assumes both bits are on the same port). Valid values
- are 0..3 for ports A..D.
-
I2C_ACTIVE
The code necessary to make the I2C data line active
If defined, then this indicates the I2C bus number for the RTC.
If not defined, then U-Boot assumes that RTC is on I2C bus 0.
- CONFIG_SYS_DTT_BUS_NUM
-
- If defined, then this indicates the I2C bus number for the DTT.
- If not defined, then U-Boot assumes that DTT is on I2C bus 0.
-
- CONFIG_SYS_I2C_DTT_ADDR:
-
- If defined, specifies the I2C address of the DTT device.
- If not defined, then U-Boot uses predefined value for
- specified DTT device.
-
CONFIG_SOFT_I2C_READ_REPEATED_START
defining this will force the i2c_read() function in
Specify the number of FPGA devices to support.
- CONFIG_CMD_FPGA_LOADMK
-
- Enable support for fpga loadmk command
-
- CONFIG_CMD_FPGA_LOADP
-
- Enable support for fpga loadp command - load partial bitstream
-
- CONFIG_CMD_FPGA_LOADBP
-
- Enable support for fpga loadbp command - load partial bitstream
- (Xilinx only)
-
CONFIG_SYS_FPGA_PROG_FEEDBACK
Enable printing of hash marks during FPGA configuration.
following board configurations are known to be
"pRAM-clean":
- IVMS8, IVML24, SPD8xx, TQM8xxL,
+ IVMS8, IVML24, SPD8xx,
HERMES, IP860, RPXlite, LWMON,
- FLAGADM, TQM8260
+ FLAGADM
- Access to physical memory region (> 4GB)
Some basic support is provided for operations on memory not
Define this option to include a destructive SPI flash
test ('sf test').
- CONFIG_SF_DUAL_FLASH Dual flash memories
-
- Define this option to use dual flash support where two flash
- memories can be connected with a given cs line.
- Currently Xilinx Zynq qspi supports these type of connections.
-
- SystemACE Support:
CONFIG_SYSTEMACE
A better solution is to properly configure the firewall,
but sometimes that is not allowed.
-- Hashing support:
- CONFIG_CMD_HASH
-
- This enables a generic 'hash' command which can produce
- hashes / digests from a few algorithms (e.g. SHA1, SHA256).
-
- CONFIG_HASH_VERIFY
-
- Enable the hash verify command (hash -v). This adds to code
- size a little.
-
- Note: There is also a sha1sum command, which should perhaps
- be deprecated in favour of 'hash sha1'.
-
-- Freescale i.MX specific commands:
- CONFIG_CMD_HDMIDETECT
- This enables 'hdmidet' command which returns true if an
- HDMI monitor is detected. This command is i.MX 6 specific.
-
- bootcount support:
CONFIG_BOOTCOUNT_LIMIT
kernel. Needed for UBI support.
- UBI support
- CONFIG_CMD_UBI
-
- Adds commands for interacting with MTD partitions formatted
- with the UBI flash translation layer
-
- Requires also defining CONFIG_RBTREE
-
CONFIG_UBI_SILENCE_MSG
Make the verbose messages from UBI stop printing. This leaves
default: 0
- UBIFS support
- CONFIG_CMD_UBIFS
-
- Adds commands for interacting with UBI volumes formatted as
- UBIFS. UBIFS is read-only in u-boot.
-
- Requires UBI support as well as CONFIG_LZO
-
CONFIG_UBIFS_SILENCE_MSG
Make the verbose messages from UBIFS stop printing. This leaves
Builds up envcrc with the target environment so that external utils
may easily extract it and embed it in final U-Boot images.
-- CONFIG_ENV_IS_IN_FLASH:
-
- Define this if the environment is in flash memory.
-
- a) The environment occupies one whole flash sector, which is
- "embedded" in the text segment with the U-Boot code. This
- happens usually with "bottom boot sector" or "top boot
- sector" type flash chips, which have several smaller
- sectors at the start or the end. For instance, such a
- layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
- such a case you would place the environment in one of the
- 4 kB sectors - with U-Boot code before and after it. With
- "top boot sector" type flash chips, you would put the
- environment in one of the last sectors, leaving a gap
- between U-Boot and the environment.
-
- - CONFIG_ENV_OFFSET:
-
- Offset of environment data (variable area) to the
- beginning of flash memory; for instance, with bottom boot
- type flash chips the second sector can be used: the offset
- for this sector is given here.
-
- CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
-
- - CONFIG_ENV_ADDR:
-
- This is just another way to specify the start address of
- the flash sector containing the environment (instead of
- CONFIG_ENV_OFFSET).
-
- - CONFIG_ENV_SECT_SIZE:
-
- Size of the sector containing the environment.
-
-
- b) Sometimes flash chips have few, equal sized, BIG sectors.
- In such a case you don't want to spend a whole sector for
- the environment.
-
- - CONFIG_ENV_SIZE:
-
- If you use this in combination with CONFIG_ENV_IS_IN_FLASH
- and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
- of this flash sector for the environment. This saves
- memory for the RAM copy of the environment.
-
- It may also save flash memory if you decide to use this
- when your environment is "embedded" within U-Boot code,
- since then the remainder of the flash sector could be used
- for U-Boot code. It should be pointed out that this is
- STRONGLY DISCOURAGED from a robustness point of view:
- updating the environment in flash makes it always
- necessary to erase the WHOLE sector. If something goes
- wrong before the contents has been restored from a copy in
- RAM, your target system will be dead.
-
- - CONFIG_ENV_ADDR_REDUND
- CONFIG_ENV_SIZE_REDUND
-
- These settings describe a second storage area used to hold
- a redundant copy of the environment data, so that there is
- a valid backup copy in case there is a power failure during
- a "saveenv" operation.
-
-BE CAREFUL! Any changes to the flash layout, and some changes to the
-source code will make it necessary to adapt <board>/u-boot.lds*
-accordingly!
-
-
-- CONFIG_ENV_IS_IN_NVRAM:
-
- Define this if you have some non-volatile memory device
- (NVRAM, battery buffered SRAM) which you want to use for the
- environment.
-
- - CONFIG_ENV_ADDR:
- - CONFIG_ENV_SIZE:
-
- These two #defines are used to determine the memory area you
- want to use for environment. It is assumed that this memory
- can just be read and written to, without any special
- provision.
-
BE CAREFUL! The first access to the environment happens quite early
in U-Boot initialization (when we try to get the setting of for the
console baudrate). You *MUST* have mapped your NVRAM area then, or
keep settings there always unmodified except somebody uses "saveenv"
to save the current settings.
-
-- CONFIG_ENV_IS_IN_EEPROM:
-
- Use this if you have an EEPROM or similar serial access
- device and a driver for it.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the
- environment area within the total memory of your EEPROM.
-
- - CONFIG_SYS_I2C_EEPROM_ADDR:
- If defined, specified the chip address of the EEPROM device.
- The default address is zero.
-
- - CONFIG_SYS_I2C_EEPROM_BUS:
- If defined, specified the i2c bus of the EEPROM device.
-
- - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
- If defined, the number of bits used to address bytes in a
- single page in the EEPROM device. A 64 byte page, for example
- would require six bits.
-
- - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
- If defined, the number of milliseconds to delay between
- page writes. The default is zero milliseconds.
-
- - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
- The length in bytes of the EEPROM memory array address. Note
- that this is NOT the chip address length!
-
- - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
- EEPROM chips that implement "address overflow" are ones
- like Catalyst 24WC04/08/16 which has 9/10/11 bits of
- address and the extra bits end up in the "chip address" bit
- slots. This makes a 24WC08 (1Kbyte) chip look like four 256
- byte chips.
-
- Note that we consider the length of the address field to
- still be one byte because the extra address bits are hidden
- in the chip address.
-
- - CONFIG_SYS_EEPROM_SIZE:
- The size in bytes of the EEPROM device.
-
- - CONFIG_ENV_EEPROM_IS_ON_I2C
- define this, if you have I2C and SPI activated, and your
- EEPROM, which holds the environment, is on the I2C bus.
-
- - CONFIG_I2C_ENV_EEPROM_BUS
- if you have an Environment on an EEPROM reached over
- I2C muxes, you can define here, how to reach this
- EEPROM. For example:
-
- #define CONFIG_I2C_ENV_EEPROM_BUS 1
-
- EEPROM which holds the environment, is reached over
- a pca9547 i2c mux with address 0x70, channel 3.
-
-- CONFIG_ENV_IS_IN_DATAFLASH:
-
- Define this if you have a DataFlash memory device which you
- want to use for the environment.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_ADDR:
- - CONFIG_ENV_SIZE:
-
- These three #defines specify the offset and size of the
- environment area within the total memory of your DataFlash placed
- at the specified address.
-
-- CONFIG_ENV_IS_IN_SPI_FLASH:
-
- Define this if you have a SPI Flash memory device which you
- want to use for the environment.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the
- environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
- aligned to an erase sector boundary.
-
- - CONFIG_ENV_SECT_SIZE:
-
- Define the SPI flash's sector size.
-
- - CONFIG_ENV_OFFSET_REDUND (optional):
-
- This setting describes a second storage area of CONFIG_ENV_SIZE
- size used to hold a redundant copy of the environment data, so
- that there is a valid backup copy in case there is a power failure
- during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
- aligned to an erase sector boundary.
-
- - CONFIG_ENV_SPI_BUS (optional):
- - CONFIG_ENV_SPI_CS (optional):
-
- Define the SPI bus and chip select. If not defined they will be 0.
-
- - CONFIG_ENV_SPI_MAX_HZ (optional):
-
- Define the SPI max work clock. If not defined then use 1MHz.
-
- - CONFIG_ENV_SPI_MODE (optional):
-
- Define the SPI work mode. If not defined then use SPI_MODE_3.
-
-- CONFIG_ENV_IS_IN_REMOTE:
-
- Define this if you have a remote memory space which you
- want to use for the local device's environment.
-
- - CONFIG_ENV_ADDR:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the address and size of the
- environment area within the remote memory space. The
- local device can get the environment from remote memory
- space by SRIO or PCIE links.
-
BE CAREFUL! For some special cases, the local device can not use
"saveenv" command. For example, the local device will get the
environment stored in a remote NOR flash by SRIO or PCIE link,
but it can not erase, write this NOR flash by SRIO or PCIE interface.
-- CONFIG_ENV_IS_IN_NAND:
-
- Define this if you have a NAND device which you want to use
- for the environment.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the environment
- area within the first NAND device. CONFIG_ENV_OFFSET must be
- aligned to an erase block boundary.
-
- - CONFIG_ENV_OFFSET_REDUND (optional):
-
- This setting describes a second storage area of CONFIG_ENV_SIZE
- size used to hold a redundant copy of the environment data, so
- that there is a valid backup copy in case there is a power failure
- during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
- aligned to an erase block boundary.
-
- - CONFIG_ENV_RANGE (optional):
-
- Specifies the length of the region in which the environment
- can be written. This should be a multiple of the NAND device's
- block size. Specifying a range with more erase blocks than
- are needed to hold CONFIG_ENV_SIZE allows bad blocks within
- the range to be avoided.
-
- - CONFIG_ENV_OFFSET_OOB (optional):
-
- Enables support for dynamically retrieving the offset of the
- environment from block zero's out-of-band data. The
- "nand env.oob" command can be used to record this offset.
- Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
- using CONFIG_ENV_OFFSET_OOB.
-
- CONFIG_NAND_ENV_DST
Defines address in RAM to which the nand_spl code should copy the
environment. If redundant environment is used, it will be copied to
CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
-- CONFIG_ENV_IS_IN_UBI:
-
- Define this if you have an UBI volume that you want to use for the
- environment. This has the benefit of wear-leveling the environment
- accesses, which is important on NAND.
-
- - CONFIG_ENV_UBI_PART:
-
- Define this to a string that is the mtd partition containing the UBI.
-
- - CONFIG_ENV_UBI_VOLUME:
-
- Define this to the name of the volume that you want to store the
- environment in.
-
- - CONFIG_ENV_UBI_VOLUME_REDUND:
-
- Define this to the name of another volume to store a second copy of
- the environment in. This will enable redundant environments in UBI.
- It is assumed that both volumes are in the same MTD partition.
-
- - CONFIG_UBI_SILENCE_MSG
- - CONFIG_UBIFS_SILENCE_MSG
-
- You will probably want to define these to avoid a really noisy system
- when storing the env in UBI.
-
-- CONFIG_ENV_IS_IN_FAT:
- Define this if you want to use the FAT file system for the environment.
-
- - FAT_ENV_INTERFACE:
-
- Define this to a string that is the name of the block device.
-
- - FAT_ENV_DEVICE_AND_PART:
-
- Define this to a string to specify the partition of the device. It can
- be as following:
-
- "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
- - "D:P": device D partition P. Error occurs if device D has no
- partition table.
- - "D:0": device D.
- - "D" or "D:": device D partition 1 if device D has partition
- table, or the whole device D if has no partition
- table.
- - "D:auto": first partition in device D with bootable flag set.
- If none, first valid partition in device D. If no
- partition table then means device D.
-
- - FAT_ENV_FILE:
-
- It's a string of the FAT file name. This file use to store the
- environment.
-
- - CONFIG_FAT_WRITE:
- This should be defined. Otherwise it cannot save the environment file.
-
-- CONFIG_ENV_IS_IN_MMC:
-
- Define this if you have an MMC device which you want to use for the
- environment.
-
- - CONFIG_SYS_MMC_ENV_DEV:
-
- Specifies which MMC device the environment is stored in.
-
- - CONFIG_SYS_MMC_ENV_PART (optional):
-
- Specifies which MMC partition the environment is stored in. If not
- set, defaults to partition 0, the user area. Common values might be
- 1 (first MMC boot partition), 2 (second MMC boot partition).
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the environment
- area within the specified MMC device.
-
- If offset is positive (the usual case), it is treated as relative to
- the start of the MMC partition. If offset is negative, it is treated
- as relative to the end of the MMC partition. This can be useful if
- your board may be fitted with different MMC devices, which have
- different sizes for the MMC partitions, and you always want the
- environment placed at the very end of the partition, to leave the
- maximum possible space before it, to store other data.
-
- These two values are in units of bytes, but must be aligned to an
- MMC sector boundary.
-
- - CONFIG_ENV_OFFSET_REDUND (optional):
-
- Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
- hold a redundant copy of the environment data. This provides a
- valid backup copy in case the other copy is corrupted, e.g. due
- to a power failure during a "saveenv" operation.
-
- This value may also be positive or negative; this is handled in the
- same way as CONFIG_ENV_OFFSET.
-
- This value is also in units of bytes, but must also be aligned to
- an MMC sector boundary.
-
- - CONFIG_ENV_SIZE_REDUND (optional):
-
- This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
- set. If this value is set, it must be set to the same value as
- CONFIG_ENV_SIZE.
-
-- CONFIG_SYS_SPI_INIT_OFFSET
-
- Defines offset to the initial SPI buffer area in DPRAM. The
- area is used at an early stage (ROM part) if the environment
- is configured to reside in the SPI EEPROM: We need a 520 byte
- scratch DPRAM area. It is used between the two initialization
- calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
- to be a good choice since it makes it far enough from the
- start of the data area as well as from the stack pointer.
-
Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
created; also, when using EEPROM you will have to use getenv_f()
- CONFIG_SYS_CACHELINE_SIZE:
Cache Line Size of the CPU.
-- CONFIG_SYS_DEFAULT_IMMR:
- Default address of the IMMR after system reset.
-
- Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
- and RPXsuper) to be able to adjust the position of
- the IMMR register after a reset.
-
- CONFIG_SYS_CCSRBAR_DEFAULT:
Default (power-on reset) physical address of CCSR on Freescale
PowerPC SOCs.
Virtual address of CCSR. On a 32-bit build, this is typically
the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
- CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
- for cross-platform code that uses that macro instead.
-
- CONFIG_SYS_CCSRBAR_PHYS:
Physical address of CCSR. CCSR can be relocated to a new
physical address, if desired. In this case, this macro should
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
- doing! (11-4) [MPC8xx/82xx systems only]
+ doing! (11-4) [MPC8xx systems only]
- CONFIG_SYS_INIT_RAM_ADDR:
sequences.
U-Boot uses the following memory types:
- - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
- - MPC824X: data cache
- - PPC4xx: data cache
+ - MPC8xx: IMMR (internal memory of the CPU)
- CONFIG_SYS_GBL_DATA_OFFSET:
point to an otherwise UNUSED address space between
the top of RAM and the start of the PCI space.
-- CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
-
-- CONFIG_SYS_SYPCR: System Protection Control (11-9)
-
-- CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
-
-- CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
-
-- CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
-
- CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
- CONFIG_SYS_OR_TIMING_SDRAM:
- CONFIG_SYS_MAMR_PTA:
periodic timer for refresh
-- CONFIG_SYS_DER: Debug Event Register (37-47)
-
- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
-- CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
- CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
- Machine Mode Register and Memory Periodic Timer
- Prescaler definitions (SDRAM timing)
-
-- CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
- enable I2C microcode relocation patch (MPC8xx);
- define relocation offset in DPRAM [DSP2]
-
-- CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
- enable SMC microcode relocation patch (MPC8xx);
- define relocation offset in DPRAM [SMC1]
-
-- CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
- enable SPI microcode relocation patch (MPC8xx);
- define relocation offset in DPRAM [SCC4]
-
-- CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
- Offset of the bootmode word in DPRAM used by post
- (Power On Self Tests). This definition overrides
- #define'd default value in commproc.h resp.
- cpm_8260.h.
-
-- CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
- CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
- CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
- CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
- CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
- CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
- CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
- CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
- Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
-
-- CONFIG_PCI_DISABLE_PCIE:
- Disable PCI-Express on systems where it is supported but not
- required.
-
- CONFIG_PCI_ENUM_ONLY
Only scan through and get the devices on the buses.
Don't do any setup work, presumably because someone or
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
-- CONFIG_ETHER_ON_FEC[12]
- Define to enable FEC[12] on a 8xx series processor.
-
-- CONFIG_FEC[12]_PHY
- Define to the hardcoded PHY address which corresponds
- to the given FEC; i. e.
- #define CONFIG_FEC1_PHY 4
- means that the PHY with address 4 is connected to FEC1
-
- When set to -1, means to probe for first available.
-
-- CONFIG_FEC[12]_PHY_NORXERR
- The PHY does not have a RXERR line (RMII only).
- (so program the FEC to ignore it).
-
- CONFIG_RMII
Enable RMII mode for all FECs.
Note that this is a global option, we can't
LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
INTEGRITY).
-* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
+* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
- Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
+ Currently supported: ARM, Intel x86, MIPS, NDS32, Nios II, PowerPC).
* Compression Type (uncompressed, gzip, bzip2)
* Load Address
* Entry Point
To be able to re-map memory U-Boot then jumps to its link address.
To be able to implement the initialization code in C, a (small!)
initial stack is set up in the internal Dual Ported RAM (in case CPUs
-which provide such a feature like MPC8xx or MPC8260), or in a locked
-part of the data cache. After that, U-Boot initializes the CPU core,
-the caches and the SIU.
+which provide such a feature like), or in a locked part of the data
+cache. After that, U-Boot initializes the CPU core, the caches and
+the SIU.
Next, all (potentially) available memory banks are mapped using a
preliminary mapping. For example, we put them on 512 MB boundaries