Kconfig: Remove CONFIG_CLOCKS_IN_MHZ

[platform/kernel/u-boot.git] / README

diff --git a/README b/README
index 2e8ad3b..020918a 100644 (file)
--- a/README
+++ b/README
@@ -559,19 +559,6 @@ The following options need to be configured:
                such as ARM architectural timer initialization.
 
 - Linux Kernel Interface:
-               CONFIG_CLOCKS_IN_MHZ
-
-               U-Boot stores all clock information in Hz
-               internally. For binary compatibility with older Linux
-               kernels (which expect the clocks passed in the
-               bd_info data to be in MHz) the environment variable
-               "clocks_in_mhz" can be defined so that U-Boot
-               converts clock data to MHZ before passing it to the
-               Linux kernel.
-               When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
-               "clocks_in_mhz=1" is automatically included in the
-               default environment.
-
                CONFIG_MEMSIZE_IN_BYTES         [relevant for MIPS only]
 
                When transferring memsize parameter to Linux, some versions
@@ -670,11 +657,6 @@ The following options need to be configured:
                Define this variable to enable hw flow control in serial driver.
                Current user of this option is drivers/serial/nsl16550.c driver
 
-- Console Baudrate:
-               CONFIG_BAUDRATE - in bps
-               Select one of the baudrates listed in
-               CONFIG_SYS_BAUDRATE_TABLE, see below.
-
 - Autoboot Command:
                CONFIG_BOOTCOMMAND
                Only needed when CONFIG_BOOTDELAY is enabled;
@@ -889,11 +871,6 @@ The following options need to be configured:
                Allow generic access to the SPI bus on the Intel 8257x, for
                example with the "sspi" command.
 
-               CONFIG_EEPRO100
-               Support for Intel 82557/82559/82559ER chips.
-               Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
-               write routine for first time initialisation.
-
                CONFIG_TULIP
                Support for Digital 2114x chips.
 
@@ -1330,21 +1307,6 @@ The following options need to be configured:
                can be displayed via the splashscreen support or the
                bmp command.
 
-- Compression support:
-               CONFIG_GZIP
-
-               Enabled by default to support gzip compressed images.
-
-               CONFIG_BZIP2
-
-               If this option is set, support for bzip2 compressed
-               images is included. If not, only uncompressed and gzip
-               compressed images are supported.
-
-               NOTE: the bzip2 algorithm requires a lot of RAM, so
-               the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
-               be at least 4MB.
-
 - MII/PHY support:
                CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
@@ -1567,14 +1529,6 @@ The following options need to be configured:
 
                This enable the NEW i2c subsystem, and will allow you to use
                i2c commands at the u-boot command line (as long as you set
-               CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
-               based realtime clock chips or other i2c devices. See
-               common/cmd_i2c.c for a description of the command line
-               interface.
-
-               ported i2c driver to the new framework:
-               - drivers/i2c/soft_i2c.c:
-                 - activate first bus with CONFIG_SYS_I2C_SOFT define
                    CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
                    for defining speed and slave address
                  - activate second bus with I2C_SOFT_DECLARATIONS2 define
@@ -2473,14 +2427,6 @@ Configuration Settings:
 - CONFIG_SYS_BAUDRATE_TABLE:
                List of legal baudrate settings for this board.
 
-- CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
-               Begin and End addresses of the area used by the
-               simple memory test.
-
-- CONFIG_SYS_MEMTEST_SCRATCH:
-               Scratch address used by the alternate memory test
-               You only need to set this if address zero isn't writeable
-
 - CONFIG_SYS_MEM_RESERVE_SECURE
                Only implemented for ARMv8 for now.
                If defined, the size of CONFIG_SYS_MEM_RESERVE_SECURE memory
@@ -2737,10 +2683,6 @@ Configuration Settings:
        regular expression. This allows multiple variables to define the same
        flags without explicitly listing them for each variable.
 
-- CONFIG_ENV_ACCESS_IGNORE_FORCE
-       If defined, don't allow the -f switch to env set override variable
-       access flags.
-
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations: