default y if TFABOOT
help
Typically, we use an initial stack pointer address that is calculated
- by taking the statically defined CONFIG_SYS_INIT_RAM_ADDR, adding the
- statically defined CONFIG_SYS_INIT_RAM_SIZE and then subtracting the
+ by taking the statically defined CFG_SYS_INIT_RAM_ADDR, adding the
+ statically defined CFG_SYS_INIT_RAM_SIZE and then subtracting the
build-time constant of GENERATED_GBL_DATA_SIZE. On MIPS a different
but statica calculation is performed. However, some platforms will
take a different approach. Say Y here to define the address statically
config CUSTOM_SYS_INIT_SP_ADDR
hex "Static location for the initial stack pointer"
depends on HAS_CUSTOM_SYS_INIT_SP_ADDR
- default SYS_TEXT_BASE if TFABOOT
+ default TEXT_BASE if TFABOOT
config SYS_MALLOC_F
bool "Enable malloc() pool before relocation"
default 0x4000 if SANDBOX || RISCV || ARCH_APPLE || ROCKCHIP_RK3368 || \
ROCKCHIP_RK3399
default 0x8000 if RCAR_GEN3
- default 0x10000 if ARCH_IMX8 || (ARCH_IMX8M && !IMX8MQ)
+ default 0x10000 if ARCH_IMX8 || ARCH_IMX8M
default 0x2000
help
Before relocation, memory is very limited on many platforms. Still,
default 0x4000000 if SANDBOX
default 0x2000000 if ARCH_ROCKCHIP || ARCH_OMAP2PLUS || ARCH_MESON
default 0x200000 if ARCH_BMIPS || X86
- default 0x120000 if MACH_SUNIV
- default 0x220000 if MACH_SUN8I_V3S
- default 0x4020000 if ARCH_SUNXI
+ default 0x4020000 if SUNXI_MINIMUM_DRAM_MB >= 256
+ default 0x220000 if SUNXI_MINIMUM_DRAM_MB >= 64
+ default 0x120000 if SUNXI_MINIMUM_DRAM_MB >= 32
default 0x400000
help
This defines memory to be allocated for Dynamic allocation
depends on SYS_MALLOC_F && SPL
default 0 if !SPL_FRAMEWORK
default 0x2800 if RCAR_GEN3
+ default 0x2000 if IMX8MQ
default SYS_MALLOC_F_LEN
help
In SPL memory is very limited on many platforms. Still,
particular needs this to operate, so that it can allocate the
initial serial device and any others that are needed.
- It is possible to enable CONFIG_SYS_SPL_MALLOC_START to start a new
+ It is possible to enable CFG_SYS_SPL_MALLOC_START to start a new
malloc() region in SDRAM once it is inited.
config TPL_SYS_MALLOC_F_LEN
string "Build target special images"
default "u-boot-with-spl.sfp" if TARGET_SOCFPGA_ARRIA10
default "u-boot-with-spl.sfp" if TARGET_SOCFPGA_GEN5
- default "u-boot-spl.kwb" if ARCH_MVEBU && SPL
+ default "u-boot-with-spl.kwb" if ARCH_MVEBU && SPL
default "u-boot-elf.srec" if RCAR_GEN3
default "u-boot.itb" if !BINMAN && SPL_LOAD_FIT && (ARCH_ROCKCHIP || \
ARCH_SUNXI || RISCV || ARCH_ZYNQMP)
config STACK_SIZE
hex "Define max stack size that can be used by U-Boot"
- default 0x4000000 if ARCH_VERSAL || ARCH_ZYNQMP
+ default 0x4000000 if ARCH_VERSAL_NET || ARCH_VERSAL || ARCH_ZYNQMP
default 0x200000 if MICROBLAZE
default 0x1000000
help
default 0x10000 if TARGET_TRICORDER
default 0x0
+config SYS_MONITOR_LEN
+ int "Maximum size in bytes reserved for U-Boot in memory"
+ default 1048576 if X86
+ default 0
+ help
+ Size of memory reserved for monitor code, used to determine
+ _at_compile_time_ (!) if the environment is embedded within the
+ U-Boot image, or in a separate flash sector, among other uses where
+ we need to set a maximum size of the U-Boot binary itself that will
+ be loaded.
+
config MP
bool "Support for multiprocessor"
help